Blum  |  SKU: 701171

System Screw 0mm Blum Clip Top Frameless Mounting Plate

$322 Each

Description

  • This Blum mounting plate mounts on the inside wall of the cabinet (not on the face frame).
  • For use with Blum's Half Crank Clip Top hinges where you would use back-to-back screws or system screws.
  • Mounting plates are sized by height. Each mounting plate in combination with the bore distance of the hinge creates the door overlay (for an overlay door) or the reveal (for an inset door or back to back door)
  • For back-to-back door installations, we offer Back-to-Back screws. Back-to-Back installations are where two doors are installed to the same cabinet side panel. It is recommended that the mounting plates for these hinges be installed with Back-to-Back screws (a male/female type screw) so that the screws do not interfere with each other.

Replacements

  • When replacing worn out or broken Blum hinges, it is a good idea to replace all the hinges and mounting plates on your door at the same time.

Warranty

Limited Warranty
Blum, Inc. (Blum) warrants its lift systems, hinges and/or drawer runners,
contained in this product, but not the product itself, against defects in material
and workmanship for as long as the original consumer purchaser owns the
products. This warranty is a warranty of replacement only. Blum specifically
does not warrant removal of the defective hardware nor installation of new
hardware. This warranty does not cover hardware which has been incorrectly
installed, exposed to excessive loads or otherwise used in any manner contrary
to its intended purpose. In the event the defective Blum hardware is obsolete or
has been discontinued, Blum reserves the right to replace the defective
hardware with a current offering. No guarantee of interchangeability is offered.

Other terms and conditions:
ALL WARRANTIES IMPLIED BY STATE LAW, INCLUDING THE IMPLIED
WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR
PURPOSE, ARE EXPRESSLY LIMITED AS SET FORTH ABOVE.

However, some states do not allow limitations on how long an implied warranty lasts, so the above limitation may not apply to you.

WITH THE EXCEPTION OF ANY WARRANTIES IMPLIED BY STATE LAW AS
HEREBY LIMITED, THE FOREGOING EXPRESS LIMITED WARRANTY IS
EXCLUSIVE AND IN LIEU OF ANY OTHER WARRANTIES OF BLUM WITH
RESPECT TO THE REPAIR OR REPLACEMENT OF ANY PROPS OR PARTS.
IN NO EVENT SHALL BLUM BE LIABLE FOR CONSEQUENTIAL OR INCIDENTAL
DAMAGES RESULTING FROM THE USE, INSTALLATION, PERFORMANCE OR
FAILURE OF ITS HARDWARE.

However, some states do allow the exclusion of limitation of incidental or consequential damages, so the above exclusion may not apply to you. This limited warranty gives you specific legal rights, and you may also have other rights which vary from state to state.

Store Policies & Information

Shipping & Delivery
Returns
Contact Us

We have been selling hardware and hinges for over 130 years. When you shop with us, you can count on prompt, personal customer service and reliable support.

Page Code: 701171

  • Manufacturer
    Blum
  • Model Number
    175H910
  • Finish Name
    Nickel
  • Material
    Cast Metal
  • Mounting Hardware Included
    No
  • Mounting Hardware Type
    Blum Back-To-Back Screws
    Two #6 x 5/8" Flat Head Screws

Payment & Security

Payment methods

  • American Express
  • Apple Pay
  • Discover
  • Mastercard
  • PayPal
  • Shop Pay
  • Venmo
  • Visa

Your payment information is processed securely. We do not store credit card details nor have access to your credit card information.

Related Products

A table comparing the facets of 5 products
Facet
Back to Back Screws
Back to Back Screws
View details
Blum 110 Degree Hinge for Back-to-Back Overlay Cabinets - Bundle
View details
Blum 120 Degree Hinge for Back-to-Back Overlay Cabinets - Bundle
View details
Blum 170 Degree Hinge for Back-to-Back Overlay Cabinets - Bundle
View details
Blum Blumotion Hinge for Back-to-Back Overlay Cabinets - Bundle
View details
Price
Price
$178 Each
$603 Per Bundle
$733 Per Bundle
From $1033 Per Bundle
$1111 Per Bundle
Description
DescriptionThis screw is for European hinges used on back to back or twin overlay doors where the hinges are installed back to back... Blum's half cranked clip top hinge for back-to-back doors. Please see the "Reveal & Overlay Information" document below to verify if this bundle... Blum's 120 degree half cranked clip top hinge for back-to-back doors. Please see the "Reveal & Overlay Information" document below to verify if... Blum 170 degree hinge bundle for back-to-back overlay doors on frameless cabinets. Available in self-closing and free swinging functionalities. The hinge and mounting... Please see the "Reveal & Overlay Information" document below to verify if this bundle will work for your application. Blum's half cranked clip...

We Are Here to Help

Get expert assistance with product selection and more.

Frequently Asked Questions

How long does it take to get my hardware once it's been ordered?

The delivery time depends on how far you live from our San Diego warehouse. Generally, your order will reach you in 1 to 5 business days. Shipments do not move on weekends and holidays.

Do you ship merchandise outside the United States?

At this time, we only ship to addresses in the continental United States, Alaska, and Hawaii. For APO/FPO/DPO and Canadian orders, please email info@hardwaresource.com with a list of the SKU numbers and quantities you would like to purchase, along with your complete ship to address. Once we receive this information we will email you a shipping quote. Please note: Canadian shipments have a $50.00 minimum order.

I have a hinge that I am trying to replace but I need help identifying it. Can you help?

Yes! Please click here to visit our Hinge Finder page.

Some of your hinges are sold by the each and some sell by the pair. What is the difference?

When the unit of measure says “pair” that means two hinges. Usually you need one pair of hinges per door. When the unit of measure says “each” that means one hinge. You would usually order 2 “each” hinges per door.

I want to replace my hinges. How do I make sure the screw holes on the new hinge match the screw holes on the old hinge so I do not have to redrill the holes?

Unfortunately, hinge manufacturers have never standardized the location of their screw hole patterns. Every manufacturer puts their screw holes in a slightly different place. This means that when you replace hinges you will almost certainly have to do some filling and redrilling. The exception to this is Architectural door hinges which are built to a standardized template for each size hinge.

What is your return policy?

You can see our complete return policy here: HardwareSource Returns