Blum  |  SKU: 652299

Blum 170 Degree Half Crank Hinge

$690 Each

Fasteners Not Included

Description

  • Blum 170 Degree Self-Closing Half Crank Hinge for inset or small overlay cabinet doors.
  • Note: This is the hinge only, and does not come with mounting plates or hardware. Select a bundle page below for complete units.
  • For frameless inset applications, check out our bundle page here.
  • For back-to-back and small overlay applications, check out our bundle page here.

Available for purchase separately:

  • Plastic Dowels and dowel screws, used on manufactured wood products where wood screws do not hold well found here.
  • Restriction clip. Limits angle of opening to 130 degrees (SKU# 652033).
  • Blum Touch Latch for Self-Closing Doors found here.
  • 35mm Forstner Bit, for new installations (SKU# 204000).
  • Ecodrill, installation jig, for new installations (SKU# 701000).

Warranty

Limited Warranty
Blum, Inc. (Blum) warrants its lift systems, hinges and/or drawer runners,
contained in this product, but not the product itself, against defects in material
and workmanship for as long as the original consumer purchaser owns the
products. This warranty is a warranty of replacement only. Blum specifically
does not warrant removal of the defective hardware nor installation of new
hardware. This warranty does not cover hardware which has been incorrectly
installed, exposed to excessive loads or otherwise used in any manner contrary
to its intended purpose. In the event the defective Blum hardware is obsolete or
has been discontinued, Blum reserves the right to replace the defective
hardware with a current offering. No guarantee of interchangeability is offered.

Other terms and conditions:
ALL WARRANTIES IMPLIED BY STATE LAW, INCLUDING THE IMPLIED
WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR
PURPOSE, ARE EXPRESSLY LIMITED AS SET FORTH ABOVE.

However, some states do not allow limitations on how long an implied warranty lasts, so the above limitation may not apply to you.

WITH THE EXCEPTION OF ANY WARRANTIES IMPLIED BY STATE LAW AS
HEREBY LIMITED, THE FOREGOING EXPRESS LIMITED WARRANTY IS
EXCLUSIVE AND IN LIEU OF ANY OTHER WARRANTIES OF BLUM WITH
RESPECT TO THE REPAIR OR REPLACEMENT OF ANY PROPS OR PARTS.
IN NO EVENT SHALL BLUM BE LIABLE FOR CONSEQUENTIAL OR INCIDENTAL
DAMAGES RESULTING FROM THE USE, INSTALLATION, PERFORMANCE OR
FAILURE OF ITS HARDWARE.

However, some states do allow the exclusion of limitation of incidental or consequential damages, so the above exclusion may not apply to you. This limited warranty gives you specific legal rights, and you may also have other rights which vary from state to state.

Store Policies & Information

Shipping & Delivery
Returns
Contact Us

We have been selling hardware and hinges for over 130 years. When you shop with us, you can count on prompt, personal customer service and reliable support.

Page Code: 652299

  • Manufacturer
    Blum
  • Model Number
    B71T665
  • Finish Name
    Nickel
  • Material
    Steel
  • Self-Closing
    Yes
  • Plate Connection Type
    Clip-On
  • Opening Angle
    170 Degrees
  • Cup Diameter
    35mm
  • Screw Hole Spacing
    45mm (1-3/4")
  • Mounting Hardware Included
    No
  • Mounting Hardware Type
    Two #6 x 5/8" Flat Head Screws (Our SKU 652360)

Payment & Security

Payment methods

  • American Express
  • Apple Pay
  • Discover
  • Mastercard
  • PayPal
  • Shop Pay
  • Venmo
  • Visa

Your payment information is processed securely. We do not store credit card details nor have access to your credit card information.

Related Products

A table comparing the facets of 5 products
Facet
Blum Clip Top Frameless Mounting Plate
View details
Blum 130 Degree Restriction Clip
View details
Blum Cover Plate For 170 Degree Hinges
Blum Cover Plate For 170 Degree Hinges
View details
Soft-Close Clip On Devices for Blum Hinges
View details
#6 x 5/8" European Hinge Screw
View details
Price
Price
From $259 Each
$109 Each
$069 Each
From $269 Each
$006 Each
Description
Description  This Blum mounting plate mounts on the inside wall of the cabinet (not on the face frame). For use with Blum's Clip... Restriction clip reduces the opening angle of a Blum 170 degree hinge to 130 degrees. This is a valuable option if you have... Blum cover caps are designed to cover up the screws on Blum hinges. Gives Blum European hinges a more elegant, finished look. Cover... This Blumotion soft-close device allows cabinet doors to close without slamming. The braking system inside the device creates a perfect closing motion. Works... Specially made for European and Blum hinges. Steel base material. This #6 screw is for most European hinges and mounting plates. The #7...

We Are Here to Help

Get expert assistance with product selection and more.

Frequently Asked Questions

How long does it take to get my hardware once it's been ordered?

The delivery time depends on how far you live from our San Diego warehouse. Generally, your order will reach you in 1 to 5 business days. Shipments do not move on weekends and holidays.

Do you ship merchandise outside the United States?

At this time, we only ship to addresses in the continental United States, Alaska, and Hawaii. For APO/FPO/DPO and Canadian orders, please email info@hardwaresource.com with a list of the SKU numbers and quantities you would like to purchase, along with your complete ship to address. Once we receive this information we will email you a shipping quote. Please note: Canadian shipments have a $50.00 minimum order.

I have a hinge that I am trying to replace but I need help identifying it. Can you help?

Yes! Please click here to visit our Hinge Finder page.

Some of your hinges are sold by the each and some sell by the pair. What is the difference?

When the unit of measure says “pair” that means two hinges. Usually you need one pair of hinges per door. When the unit of measure says “each” that means one hinge. You would usually order 2 “each” hinges per door.

I want to replace my hinges. How do I make sure the screw holes on the new hinge match the screw holes on the old hinge so I do not have to redrill the holes?

Unfortunately, hinge manufacturers have never standardized the location of their screw hole patterns. Every manufacturer puts their screw holes in a slightly different place. This means that when you replace hinges you will almost certainly have to do some filling and redrilling. The exception to this is Architectural door hinges which are built to a standardized template for each size hinge.

What is your return policy?

You can see our complete return policy here: HardwareSource Returns