• Under cabinet cook book holder allows cook book storage underneath your kitchen cabinet. To use cook book simply pull down the front of the holder and your cook book can be viewed at the perfect angle.
• The cook book holder uses a compound action hinge with springs to hold it in both the open and closed position.
• Clear acrylic cook book platform measures 18-1/4" wide by 9-1/4" deep.
• In the open position the bottom of the cook book holder is 11-1/2" from the underside of the cabinet (downward projection).
• In the closed position the bottom of the cook book holder is 3" from the underside of the cabinet.
• To properly install the cook book holder it needs 20.5" of width and 10.5" of depth under the cabinet.
• Mounting screws and installation instructions are included.

Finishes:

• Clear acrylic tray

• Stainless steel pulls for drawers and cabinets.
• Available in sizes ranging from 5" to 56.5" long.
• All sizes have two attachment legs except for the two largest sizes (46" and 54") which have 3 attachment legs.
• The "center-to-center" dimension refers to the distance between the center of the screwholes of the attachment legs.
• The diameter of the pull is approximately 1/2" (actual dimension is 12mm).
• The projection (or height) of the pull is 1.3".
• Made from solid stainless steel.
• Two sets of screws are included. One set is 1-1/8" long. The second set is 1-7/16" long. PLEASE NOTE; screws are made from plated steel.

Finishes:

• Stainless Steel

• These hinges allow the cabinet panel that is found in front of a kitchen sink to tip out 45 degrees.
• This item is the replacement pair of hinges only, if you need the trays and hinges see our Tip-Out Tray Kits

Finishes:

• Zinc chromate plated

• This product consists of 2 trays and 2 pair of hinges and the instructions that allow you to convert the cabinet panel in front of your kitchen sink into a tip-out tray for extra storage.
• Each tray measures 11" long by 3-3/4" high by 2-1/16". deep
• Screws are included.

Finishes:

• Trays are white plastic
• Hinges are zinc chromate plated

• This device may be used for limiting the swing of a cabinet door anywhere from 0 to slightly more than 90 degrees depending on how you elect to install the mounting plates.
• A typical installation would be to mount the right angle swivel plate on the inside surface of the door and to mount the second plate on the underside of a shelf or the underside of the top of the cabinet.
• Available in a "Left Hand" or "Right Hand" model.
• Use a "Right Hand" model if your door is hinged on the right hand side of the cabinet as you are facing the cabinet.
• This device may also be used to support drop down desk tops. If ordering for use as a drop down desk support, order one "Left Hand" and one "Right Hand" model.
• Uses 2 each #4 flat head screws (not included but offered for purchase during checkout).
• PLEASE NOTE: the photos to the left show the product in a vertical position. When used as a cabinet restraint they will be installed in a horizontal positon.

Finishes:

• Nickel

• Restraint chain for cabinet doors will keep your door from opening too far. Keeps doors from hitting other doors, glass panels, TV monitors,etc.
• Overall length is 12".
• The attachment plates measure 1.5" x 1".
• Made from steel base material.
• Matching wood screws are included.

Finishes:

• Brass Plated
• Nickel Plated
• Oil Rubbed Bronze

• Double magnetic catch is used for double door cabinets
• Magnetic catches are used on cabinets with free swinging (non self-closing) hinges
• Measures 3-3/8" long by 1" wide by 1/2" tall
• Steel base material
• Mounting screws are included

Finishes:

• Zinc plated

• Used on cabinets with free swinging (non-self closing) doors
• Catch measures 2" long by 1-1/4" wide by 1/2" tall
• Mounting screws are included
• Plastic and steel base material

Finishes:

• Brown plastic

• Magnetic catches are used on cabinets with free swinging (non self-closing) hinges
• Catch measures 2" long by 1-1/4" wide by 5/8" tall
• Aluminum base material
• Mounting screws are included

Finishes:

• Natural aluminum

• Magnetic touch latch for cabinet doors
• When you push in on cabinet door, door pops out and is released from magnetic hold.
• Includes mounting screws and steel plate for inside of cabinet door.
• Size is approximately 1-3/4" long by 1-3/4" wide by 3/4" projection.

Finishes:

• Brown plastic
• White Plastic

• It is known as a "Secret Gate Latch" but it is actually more of a cabinet latch.
• It is used in banks, offices, restaurants and bars as a latch to secure a hinged countertop.
• Because the button to unlatch it is not obvious it acts as a low security device.
• It can be used on any hinged device where you can reach around and access the button on the latch.
• Made from aluminum with some steel parts.
• Latch is reversible (open device and flip latch over to reverse)
• Gap must be no more than 1/4" for latch to work (latch projects 3/8").
• Latch is 3.5" long and 2" wide. Strike is 3/4" long and 2" wide. Latch is approximately 5/8" thick.
• Oval head wood screws are included.

Finishes:

• Sprayed Aluminum Finish (similiar to polished chrome)

• A flush ring pull allows you to mortise the pull into the door so that it is completely flush with the door surface.
• Available in two sizes; Small and Large.
• The Small size measures 1-3/8" wide by 1-3/4" tall by 7/16" thick (approximate mortise depth).
• The Large size measures 1-15/16" wide by 2-1/2" tall by 1/2" thick (approximate mortise depth).
• Made from solid brass base material.
• Matching wood screws are included.

Finishes:

• Satin Nickel
• Oil Rubbed Bronze
• Polished Brass

• Cabinet knobs made from solid stainless steel with a brushed or satin finish.
• Available in two sizes; small and large.
• Small size measures 1" in diameter, 7/8" tall with a 3/4" diameter base.
• Large size measures 1-3/16" in diameter, by 15/16" tall with a 13/16" diameter base.
• A 1-3/16" long machine screw is included. PLEASE NOTE; the machine screw is made from plated steel, not stainless steel.

Finishes:

• Satin Stainless Steel

• Tee style cabinet pull made from solid stainless steel.
• Pull measures 2" wide by 1-1/2" tall.
• Made from 3/8" and 1/2" diameter material.
• PLEASE NOTE; two different length machine screws are included (1-1/8" and 1-1/2") but they are made from plated steel not solid stainless steel.

Finishes:

• Satin Stainless Steel

• Solid stainless steel finger pull for sliding cabinet doors, pocket doors, etc.
• May be flush mounted.
• Pull measures 2-3/4" tall by 15/16" wide. Plate thickness is 1/8". Fits in a 7/8" deep cutout.
• Wood screws are included.

Finishes:

• Satin Stainless Steel

• Forged iron pull for cabinet doors.
• Pull measures 4-7/8" tall, by 7/8" wide (at mounting plate) by 7/8" projection.
• Made from steel base material.
• Includes matching wood screws.
• This pull is made to match our other forged iron hardware (hinges, etc.).

Finishes:

• Black Forged Iron