• We have a good selection of decorative straps for doors. These decorative straps are used in combination with an appropriate butt hinge. A butt hinge gives you a much higher weight rating for your door than a strap hinge. The decorative strap hinge gives you the look you are after.

Finishes:

• Black Iron
• Hammered Black Iron
• Flat Black Iron

Grilles are installed on the exterior of your door and provide security for your speakeasy opening.

Large pulls for doors which do not require a latch or lock.

• Clavos are a decorative hardware item that is used to dress up doors, cabinets, etc.
• Available in either a round, square or pyramid shape and in various sizes.
• Fits into a 7/32" diameter by 1/2" deep drilled hole.
• Forged iron base material.

Finishes:

• Black

• Clavos are a decorative hardware item that is used to dress up doors, cabinets etc. Clavos may also be used to hide a screwhead.
• These clavos install with a welded on nail. To install predrill a 1/8" or slightly larger hole and gently push the clavos into the wood. It is not advisable to use a hammer to install these clavos.
• Made from steel.
• There are two different diameter sizes available. They both project about 1/2" from the surface after installion.

Finishes:

• Black

• Solid bronze door studs (also known as "Clavos" are a decorative item used to dress up doors or gates.
• They are made from solid bronze and will age like the other bronze items shown on our website.
• These door studs are available in two shapes; round and square. And they are available in two sizes; 1" and 2".
• Door studs install by gently taping into a pre-drilled hole in the door or gate.

Finishes:

• Solid Natural Bronze

• Door holders allow you to open the door to a set position between 85 and 110 degrees
• The door then holds at that set position until you release it
• Not handed, works on left or right hand opening doors
• Designed for installation in virtually all types of doors and frames, including doors with conventional butt hinges, offset pivots, continuous hinges, swing clear hinges, Soss hinges and others.
• Allows for variable mounting positions ranging from 85 degrees to 110 degrees of opening.
• Available in two different types; One for door openings from 27-1/16" to 33" and the other for door openings from 33-1/16" to 39"
• PLEASE NOTE; Overhead door holders are made from steel base material. The Satin Stainless steel model is made from stainless steel but has internal parts made from steel and other non-stainless steel materials.

Finishes:

• Satin Stainless Steel
• Oil Rubbed Bronze
• Polished Brass

• This heavy duty chain door restraint can be installed to restrict the swing of a full size door. For example in a windy area or in an area where the door would hit something if opened too far.
• The chain door restraint is made up of two solid brass end brackets, each attached to a spring. The middle part is a heavy duty solid steel welded chain. The length of chain is covered by a grey vinyl covering.
• Recommended for doors with a maximum width of 36".
• Screws for the end brackets are included.
• The total length of the chain door restraint is 26.5". The end bracket mounting plate measures 1.5" by 1.5

Finishes:

• Oil Rubbed Bronze

• adjustable doorstop installs in door hinge and is held in place by hinge pin
• this hinge pin door stop is adjustable to stop the door at your choice of 5 different points
• solid brass material
• nylon hinge pin bearing (1/4" inside diameter)
• rubber bumpers to protect door and door molding
• size is approximately 3-1/2" x 2-1/4" as shown in the wide open position

Finishes:

• Brass
• Oil Rubbed Bronze
• Satin Nickel

• Installs under top of hinge pin on your door hinge to provide a door stop
• Solid Brass base material
• Adjustable
• Rubber bumpers protect your door and molding around door jamb
• Door stop has a nylon hinge pin bushing (not shown) with 1/4" inside diameter
• The nylon hinge pin bushing can be removed which will provide a 5/16" inside diameter
• Compact design (approximate size is 2-1/4" x 1-3/4")

Finishes:

• Satin Nickel
• Polished Brass
• Oil Rubbed Bronze

• This door stop is great for areas where you need an extra tall door stop (for example on out swinging doors)
• Door stop measures about 6" from the floor to the top of the black rubber bumper
• Base measures 3" in diameter, rubber bumper is about 1" in diameter
• Made of solid brass base material
• Includes all fasteners and masonary anchors needed for installation
• Includes a hook plate to attach to your door to hold the door in the open position

Finishes:

• Polished Brass
• Oil Rubbed Bronze
• Satin Nickel

• Flush magnetic door holder is made up of two parts; a floor plate and a door plate. The door plate has a strong magnet installed on its underside. The Floor plate has a flat steel plate that is hinged on one side.
• As the bottom of the door approaches the floor plate the magnet in the door plate pulls the steel lever up and grabs it to hold the door in place.
• This magnetic door holder allows for a low profile less obtrusive magnetic door holder.
• The floor plate is 2-7/16" in diameter and projects just 3/16".
• The door plate measures 2-1/4' x 3/4" and projects 1".
• For this device to work properly the bottom of your door must be no more than 7/8" from the surface of the floor below it.
• Except for the steel lever plate and the magnet the entire device is made from solid brass.
• Matching wood screws are included.

Finishes:

• Satin Nickel
• Oil Rubbed Bronze
• Lifetime Polished Brass

• These door holders are magnetic and will hold the door in the open position until it is pulled closed
• The small 1-1/4" diameter button attaches to the back of the door with two wood screws (included)
• The 3" tall magnetic holder attaches either to the floor in the vertical position or to the wall in the horizontal position.
• The magnetic holder has a 1-3/4" diameter base
• solid brass base material with some steel parts(necessary to make the magnet work) and internal steel attachment plates
• Screws and plastic masonary anchors are included

Finishes:

• Polished Brass
• Oil Rubbed Bronze
• Satin Nickel
• Antique Brass

• Magnetic door holder will hold the door in the open position until it is pulled closed.
• Features a powerful magnet which has a 30lb pull.
• Door holder is made up of two pieces; a door plate and a magnetic upright.
• The door plate attaches to the back of the door. It is approximately 2" in diameter and projects 3/4".
• The magnetic upright may be attached to either the floor in a vertical position or to the wall in a horizontal position. The magnetic upright measures 3" tall. Its baseplate is 2-1/8" in diameter.
• This product is made from a very strong polycarbonate material. The magnet has a plated steel holder and receiver.
• Mounting screws are included.

Finishes:

• Brown
• Ivory

• Magnetic door holder will hold the door in the open position until it is pulled closed.
• Features a magnet with an 18lb pull.
• Door holder is made of two pieces; a door plate and a magnetic upright.
• The door plate attaches to the back of the door. It measures 1-7/8" by 1-5/8" and projects 7/16".
• The magnetic upright may be attached to either the floor in a vertical position or to the wall in a horizontal position. It measures 2-5/8" tall. Its base plate is approximately 1-3/4" by 2".
• Product is made from plastic. The magnet is held in place by a steel holder and the wall plate has a steel plate to attract the magnet.
• Mounting screws are included.

Finishes:

• Brown
• Ivory

• Spring door holder keeps door in the open position
• Made up of two parts: the spring keeper and the post.
• The post is solid brass. The spring keeper is plated spring steel.
• After installation the door holder allows 2-5/8" clearance between surface of the door and the wall.
• The spring keeper measures about 2" tall by 2-1/8" wide (base) by 3/4" thick.
• The post measures 2" tall.
• Wood screws are included.

Finishes:

• Brass
• Oil Rubbed Bronze
• Satin Nickel

• Security studs are used for exterior doors that open outward. Doors that open outward have their hinge pins on the outside of the building.
• If a potential intruder removes the hinge pins, the security stud protects the door from being removed by locking the leaves of the hinges together.
• To install the security studs, remove two screws from your hinge. These two screws must be aligned back to back when the hinge (or door) is closed.
• Replace one of the screws with a security stud and drill a receiving hole in the other empty screwhole
• When the door closes the security stud will slide into the receiving hole locking the two hinge leaves in place
• Security studs are available to fit a #10 screwhole and a #12 screw hole
• To determine your screw hole size it is best to take a countersunk screw with a known size and place it in the hinge screw hole.
• A #10 countersunk head screw measures 11/32" across the head. A #12 countersunk head screw measures 3/8" across the head.
• The larger studs (SKU 309250 and SKU 309252) are threaded with a 12-24 machine screw thread which matches the thread that is used on metal door frames. Both size studs will work on wood doors and frames.
• They are sold by the pair (two studs)

Finishes:

• Brass plated
• Chrome plated

• Push plates are used for double acting doors which are typically located between the kitchen and dining room
• Available in two sizes; 3-1/2" by 15" and 4" x 16"
• Base material is solid brass except for the Satin Nickel (Satin Stainless) which is made from solid stainless steel.
• Matching wood screws are included
• Material is 3/64" thick

Finishes:

• Polished Brass
• Satin Nickel (Satin Stainless)
• Oil Rubbed Bronze

• Hinge pins are not universal. Each manufacturer makes his hinge pins in a different size that will only fit the hinge that it was made for.
• We carry only two hinge pins and they are made for Stanley residential hinges with a 0.234" hinge pin thickness.
• We carry them in two sizes; one fits a 3-1/2" by 3-1/2" hinge and the other fits a 4" x 4" hinge.
• Steel base material.

Finishes:

• Satin Brass Plated

• Automatic door closer device works by removing your existing hinge pin and replacing it with the "Hinge Pin Door Closer".
• Easy to install.
• Works for most doors that are 30 lbs. or less. For doors that are more than 30 lbs. use a second hinge pin door closer on the door on the bottom hinge.
• Available in brass finish or satin nickel finish.
• Comes with wrench to adjust tension.

Finishes:

• Brass
• Satin Nickel

• Touch latch is invisible from the outside of the door.
• When you use a touch latch no other hardware (knob, pull, latch) is needed on your door giving it a clean look.
• Available in either a regular duty or heavy duty model. The heavy duty model is slightly larger and has much stronger spring action. Use the heavy duty model for solid core or heavy doors.
• How it works; gently push in on the outside surface of the door. The door releases from the latch and pops outward.
• The auxiliary pusher (sold separately) is used where a vacuum condition exists (for example a small closet) or any situation where the door does not open easily.The auxiliary pusher may be used with either the regular duty or heavy duty latch.
• All mounting fasteners, a metal template and full instructions are included.
• The face and internal parts of the latch are made from solid brass and steel. The case is made from plastic.
• The auxiliary pusher is made from solid brass and nylon and the spring is made from steel.

• Adjustable ball catch and strike plate are made to hold full size doors.
• Invisible when the door is closed.
• Made from solid brass. Ball and spring are made from steel.
• Ball catch has two adjustments. The spring tension on the ball is adjustable and the amount of ball showing above the surface of the mounting plate is adjustable.
• Complete with matching wood screws and strike plate.
• PLEASE NOTE: The "Venetian Bronze" finish is a special finish made by Baldwin. To view it click on the link below.

Finishes:

• Polished Brass
• Satin Nickel
• Satin Chrome
• Oil Rubbed Bronze
• Antique Brass
• Venetian Bronze (Baldwin)
• Polished Chrome

• Pocket Door Lock fits 1-3/8" thick door
• Available in Passage type(non-locking) and Privacy type (locking)
• Measures 2-1/2" by 2-3/4"
• Fits a cutout in door measuring 2-1/4" high by 1-3/4" deep
• Split finish model is typically used in bathrooms with the polished chrome side on the bathroom side
• Matching screws are included
• Matching strike is included on privacy type (locking)

Finishes:

• Polished Brass
• Antique Brass
• Polished Chrome
• Satin Chrome
• Polished Nickel
• Satin Nickel
• Oil Rubbed Bronze
• Split Finish Polished Brass/Polished Chrome

• Pocket Door Lock fits doors from 1-3/8" to 1-3/4"
• Available in Passage type (non-locking) and Privacy type (locking)
• Measures 3-1/4" 2-1/4"
• Fits a cutout in door measuring 2-3/4" high by 1-3/4" deep
• Matching screws are included
• Matching strike plate is included in privacy type (locking)

Finishes:

• Polished Brass
• Oil Rubbed Bronze
• Satin Nickel

• Pull for pocket doors remains recessed in edge of door until you push on the tab at the bottom and pull it to the open position.
• Made from solid stainless steel material.
• Mounting plate measures 5-5/8" by 3/4".
• Fits into a cutout that is 5/8" by 4-1/2" by 2-1/4" deep.
• Pull projects about 2" when in the open position.
• Uses #8 flat head screws. Not included but offered for purchase during checkout.

Finishes:

• Satin Stainless Steel

• Tear drop style edge flush mounted edge pull for sliding doors and cabinets.
• Measures 3-3/4" tall by 1-5/16" wide by 9/16" thick.
• Edge pull fits into a cutout which measures 3-1/2" tall by 1-1/32" wide by 1/2" deep.
• Made from solid stainless steel.
• Attaches with one flat head screw which is included.
• In its normal position the pull hangs vertically in the box. Photo shows the pull at a slight angle for effect.

Finishes:

• Satin Stainless