• These shutter strap hinges are for "inset" shutters. Shutters are installed flush with the window frame when in the closed position (covering the window).
• The offset is 1/2" which gives a throw of 1". This allows the shutter to lay flat against the house when in the open position if the siding material extends 1" or less from the window frame.
• Shutter strap size is available in 4 lengths. Shutter strap measures 1-3/4" wide at the widest point. Strap is made from 12 Ga. steel.
• Pintle plate measures 1-1/2" by 3-1/2" by 1/8". Pintle diameter is 3/8".
• Shutter may be lifted off of pintles after installation.
• Hinge and pintle are zinc chromate plated for corrosion resistance and then finished in wrought iron black for a traditional look.
• Matching wood screws are included.
• Sold by the pair. A pair will hang one shutter.

Finishes:

• Wrought Iron Black

• These shutter strap hinges are for "inset" shutters. Shutters are installed flush with the window frame when in the closed position (covering the window).
• The offset is 1-1/2" which gives a throw of 3". This allows the shutter to lay flat against the house when in the open position if the siding material extends 3" or less from the window frame.
• Shutter strap size is available in 4 lengths. Shutter strap measures 1-3/4" wide at the widest point. Strap is made from 12 Ga. steel.
• Pintle plate measures 1-1/2" by 3-1/2" by 1/8". Pintle diameter is 3/8".
• Shutter may be lifted off of pintles after installation.
• Hinge and pintle are zinc chromate plated for corrosion resistance and then finished in wrought iron black for a traditional look.
• Matching wood screws are included.
• Sold by the pair. A pair will hang one shutter.

Finishes:

• Wrought Iron Black

• These shutter strap hinges are for "inset" shutters. Shutters are installed flush with the window frame when in the closed position (covering the window).
• The offset is 2-1/4" which gives a throw of 4-1/2". This allows the shutter to lay flat against the house when in the open position if the siding material extends 4-1/2" or less from the window frame.
• Shutter strap size is available in 4 lengths. Shutter strap measures 1-3/4" wide at the widest point. Strap is made from 12 Ga. steel.
• Pintle plate measures 1-1/2" by 3-1/2" by 1/8". Pintle diameter is 3/8".
• Shutter may be lifted off of pintles after installation.
• Hinge and pintle are zinc chromate plated for corrosion resistance and then finished in wrought iron black for a traditional look.
• Matching wood screws are included.
• Sold by the pair. A pair will hang one shutter.

Finishes:

• Wrought Iron Black

• These shutter strap hinges are for "inset" shutters. Shutters are installed flush with the window frame when in the closed position (covering the window).
• The offset is 3-1/4" which gives a throw of 6-1/2". This allows the shutter to lay flat against the house when in the open position if the siding material extends 6-1/2" or less from the window frame.
• Shutter strap size is available in 4 lengths. Shutter strap measures 1-3/4" wide at the widest point. Strap is made from 12 Ga. steel.
• Pintle plate measures 1-1/2" by 3-1/2" by 1/8". Pintle diameter is 3/8".
• Shutter may be lifted off of pintles after installation.
• Hinge and pintle are zinc chromate plated for corrosion resistance and then finished in wrought iron black for a traditional look.
• Matching wood screws are included.
• Sold by the pair. A pair will hang one shutter.

Finishes:

• Wrought Iron Black

• Antique style shutter hinge made for surface mounting.
• Strap leaf measures 12-1/4" by 2-3/4" at widest point.
• Vertical leaf measures 5-1/4" by 1-3/8".
• Width measurements are to center of hinge pin.
• Hinges are weight rated at 15 lbs per hinge.
• Made from steel base material. Matching wood screws are included.

Finishes:

• Black powder coated

• Antique style shutter hinge made for surface mounting (shutter and frame are flush with each other).
• Strap leaf measures 11-3/4" by 2-3/8" at widest point.
• Vertical leaf measures 4-5/16" by 1-1/8".
• Measurements are to center of hinge pin.
• Hinges are weight rated at 15 lbs. per hinge.
• Made from steel base material. Matching wood screws are included.

Finishes:

• Black Powder Coated

• This hinge is for shutters hung flush with the casing (full inset)
• Hinge measures 4-1/4" vertical and 5" horizontal. Width is 1". Pintle plate is 3-1/8" by 1-1/8"
• 1-1/4" Offset for Wood Frame Construction
• "Throw" dimension is 2-1/2". Click on link below for throw diagram.
• Loose joint hinges permit easy hanging and removal of shutters
• Made from steel base material
• Matching wood screws are included.
• This product is sold by the set. A set is 4 hinges, enough to do 2 shutters.

Finishes:

• Black

• This hinge is for shutters hung flush with the casing (full inset)
• Hinge measures 4-1/4" vertical and 5" horizontal. Width is 1'. Pintle plate is 3-1/8" by 1-1/8".
• 2-1/4" Offset for Brick Construction
• "Throw" dimension is 4-1/2". Click on link below for throw diagram.
• Loose joint hinges permit easy hanging and removal of shutters.
• Made from steel base material.
• This product is sold by the set. A set is 4 hinges, enough to do 2 shutters.
• Matching wood screws are included.

Finishes:

• Black

• This hinge is for shutters or blinds hung flush with the casing (full inset)
• Hinge measures 4-1/4" vertical and 5" horizontal. Pintle plate is 2" tall by 1-1/8" wide.
• 1-1/16" Offset for Wood frame construction.
• Throw dimension is 2-1/16". Click on link below for throw diagram.
• Loose joint hinges permit easy hanging and removal of shutters.
• Wood screws are included.
• This product is sold by the pair. A pair is enough to hang one shutter.

Finishes:

• Galvanized

• This hinge is for shutters or blinds hung flush with the casing (full inset)
• Hinge measures 4-1/4" vertical and 5" horizontal. Pintle plate is 2" tall by 1-1/8" wide.
• 2-1/8" Offset for Brick construction.
• Throw dimension is 4-1/8". Click on link below for throw diagram.
• Loose joint hinges permit easy hanging and removal of shutters.
• Wood screws are included.
• This product is sold by the pair. A pair is enough to hang one shutter.

Finishes:

• Galvanized

• Solid Bronze exterior shutter hinge matches other products from our "Solid Bronze Collection".
• For exterior shutters which are hung flush with the casing (full inset).
• Overall hinge dimensions are; 6" tall by 6-3/4" wide. Width is 1".
• Pintle plate is 3-5/8" tall by 1-3/16" wide.
• Available in two offsets; 1-1/4" Offset (for wood frame construction) and 2-1/4" Offset (for brick construction).
• The 1-1/4" Offset Type has a throw dimension of 2-1/2". Click on link below for generic throw diagram
• The 2-1/4" Offset Type has a throw dimension of 4-1/2". Click on link below for generic throw diagram.
• Loose joint hinges permit easy hanging and easy removal of shutters.
• Made from solid bronze material. Bronze is a "living finish". Please click on link below for more info on solid bronze hardware.
• This product is sold by the pair. A pair is two hinges (one top hinge and one bottom hinge), enough to hang one shutter.
• Matching wood screws are included.

• These shutter hinges are for "inset" shutters. Inset shutters are installed flush with the window frame when in the closed position (covering the window).
• The hinges are available in 3 different offsets (1/2",1-1/2" and 2-1/4") . The offset gives a "throw" which allows the shutter to lay flat against the house when in the open position.
• The "throw" is approximately double the offset. For example a hinge with a 1/2" offset has about 1" of throw.
• Pintle plate measures 1-1/2" by 3-1/2" by 1/8". Pintle diameter is 3/8".
• "L" strap measures 1-3/8" wide at widest point. Vertical part of the "L" is 5". Horizontal part of the "L" is 6".
• Shutter may be lifted off of pintles after installation.
• Hinge and pintle are zinc chromate plated for corrosion resistance and then finished in wrought iron black for a traditional look.
• Matching wood screws are included.
• For taller shutters consider using our "Middle" shutter hinges.
• Sold by the pair. A pair will hang one shutter.

Finishes:

• Wrought Iron Black

• "Middle" shutter hinges are used with our "L Type" shutter hinges as a middle hinge. They are typically used with taller shutters to keep the shutter in alignment, to help keep the shutter from warping and to give the shutter a more decorative look.
• These shutter hinges are for "inset" shutters. Inset shutters are installed flush with the window frame when in the closed position (covering the window).
• The hinges are available in 3 different offsets (1/2",1-1/2" and 2-1/4") . The offset gives a "throw" which allows the shutter to lay flat against the house when in the open position.
• The "throw" is approximately double the offset. For example a hinge with a 1/2" offset has about 1" of throw.
• Pintle plate measures 1-1/2" by 3-3/4" by 1/8". Pintle diameter is 3/8".
• Vertical strap measures 1-3/8" wide and 7" tall.
• Shutter may be lifted off of pintles after installation.
• Hinge and pintle are zinc chromate plated for corrosion resistance and then finished in wrought iron black for a traditional look.
• Matching wood screws are included.
• Sold by the pair. Order a pair to add "Middle" hinges to two shutters.

Finishes:

• Wrought Iron Black

• This surface mounted shutter hinge is used where the blind or shutter is flush with the casing. For use in frame or masonry construction.
• Smooth stainless steel strap with pintle
• Loose joint hinges permit easy hanging and removal of shutters
• Made from stainless steel base material
• This product is sold by the set. A set is 4 hinges, enough to do 2 shutters.
• Matching black stainless steel screws are included
• A pair of these shutter hinges is designed to hang a shutter of up to 20lbs. For shutters taller than 60" a third center hinge may be required.
• For masonry installation use lag type anchors.

Finishes:

• Smooth black finish

• This surface mounted shutter hinge is used where the blind or shutter is flush with the casing. For use in frame or masonry construction.
• Steel base material, galvanized for corrosion protection.
• Loose joint hinges permit easy hanging and removal of shutters
• This product is sold by the set. A set is 4 hinges, enough to do 2 shutters.
• Wood screws are included
• A pair of these shutter hinges is designed to hang a shutter of up to 20lbs. For shutters taller than 60" a third center hinge may be required.
• For masonry installation use "5/16 short" lag type anchors.

Finishes:

• Galvanized

• Smooth black stainless steel strap with pintle
• Strap measures 1" by 4-1/4" with either a 2-3/16" offset or a 1-1/4" offset.
• Pintle is 4-1/2" long by 7/16" diameter thread.
• Matching black stainless steel wood screws are included
• Loose joint hinges permit easy hanging and removal of shutters
• For use where shutters cover windows that are recessed into brick or stone you would normally use the 2-3/16" offset model.
• For use where shutters cover windows that are recessed into a wood frame you would normally use the 1-1/4"" offset model.
• Offset of hinge allows shutter to open 180 degrees
• Made from stainless steel base material
• This product is sold by the set. A set is 4 hinges, enough to do 2 shutters.
• If you need a lag anchor for this product for a masonary installation, order our SKU 244130. It is a 1/2" diameter lag anchor (in the long version) but it will work for the 7/16" diameter thread on the pintle.It is offered for purchase during checkout.

Finishes:

• Smooth black finish

• Made for shutters that are hung "Bermuda Style".
• Bermuda style shutters are installed flush with the window frame and hinged at the top of the shutter.
• The hinges are surface mounted at the top corners of the shutter.
• To open, the shutter is pushed out from the bottom and held in the open position with a 24" shutter stay (not included but offered for purchase during checkout).
• Hinge measures 3-1/2" horizontally and 6-3/16" vertically.The width of each hinge leg is about 1-1/16". Hinge projection is 1-5/16". Thickness of hinge material is about 1/4".
• Made from cast iron and coated with a black textured powder coat.
• Hinges are sold by the pair. A pair is what you need to hang one shutter.
• The hinges are not handed (hinges are reversible).
• Shutter may be easily removed after installation by removal of the hinge pin and cotter key.
• Wood screws are included.

• Small shutter hinge for exterior shutters
• "Lift-off" feature allows shutter to be easily removed after installation
• Hinge is made to be surface mounted.
• Hinge is non-handed. Will work on either left hand or right hand shutters.
• Hinge measures 2-5/16" tall by 1-7/8" wide in the open position as shown in the photo.
• Made from steel and zinc chromate plated.
• Wood screws are included.
• Sold by the pair. A pair is two complete hinges which is normally what is needed to hang one shutter.

• These shutter hinges are used for surface mounted installations.
• Allows shutter to "lift off" for cleaning or painting
• Cast iron material ready for painting
• Uses #10 flat head screws (not included)
• These shutter hinges are sold by the set. A set is 4 hinges (enough for 2 shutters)
• NOTE: two sets of shutter fasteners are included with SKU 924000. Click on 2nd link below for photo. Shutter fasteners are not included with SKU 738016.
• For explanation of "Throw" click on link below.

Finishes:

• raw cast iron, no finish

• These shutter hinges are used for full mortise installation. One leaf of the hinge is mortised into the edge of the shutter and the other leaf is mortised into the window casement.
• Click on first two links below for installation illustrations
• Choose a hinge that gives you the proper clearance away from the window casement. The "Throw" of the hinge determines this clearance.
• Cast iron base materials
• Once installed shutters may be lifted off without removing the hinges.
• When shutter is closed the hinge is designed to keep it from being lifted off by the wind.
• Mounting screw sizes are listed below but are not included
• Cast iron base material
• A set includes 4 hinges which is enough to hang 2 shutters.
• A set also includes 2 shutter fasteners which can be used to hold shutters closed if the shutter has a wooden windowsill. Click on third link below for photo of shutter fastener.

Finishes:

• Raw cast iron, no finish

• Hinge is made with a curved offset to throw the shutter clear of the window when shutter is opened
• hinge is reversible for installation on right or left side of window
• this hinge is made for shutters that are 1 inch or thicker.
• loose pin
• made of steel base material
• screws are included

Finishes:

• Black wrought iron finish