• These hinges allow you to adjust your door vertically and horizontally. Great for situations where you have doors that bind due to settling or swelling.

• A rising butt hinge solves the problem where you have a door that will not open completely because of a raised or unlevel floor or high carpeting.

• Full surface reinforcing hinges can be added to doors troubled by sagging.
• For medium and heavy weight doors subject to high frequency and abuse.
• Provides increased reinforcement at the top corner of the door and jamb where stress can occur.
• Available in two sizes; 4 inch and 4-1/2 inch. The 4 inch size is for doors with existing 4 x 4 inch hinges. The 4-1/2 inch size is for doors with existing 4-1/2 x 4-1/2 inch hinges. It is important that these hinges match your existing hinges so that the pivot points are aligned.
• PLEASE NOTE: Hinges are handed (Left Hand and Right Hand). See installation chart at link below to assure you order the correct hand hinges.
• Order one hinge per door. Hinge is installed as a reinforcing hinge on the top part of the door.
• Included with each hinge: 9 wood screws for wood frame and wood door, 9 jack nuts and short machine screws for hollow metal doors, friction wrench for jack nut installation, paper installation template, instructions. Also included are 4 grommet nuts for through-bolting if necessary and a spacer plate for the hinge leaf that attaches to the door.
• Made from steel base material.

• Large (4" tall) ball bearing no-mortise hinge(also known as non-mortise hinge).
• This hinge does not require mortising of the door or the frame (A mortise is a cut-out that the hinge fits into).
• Made for door thicknesses that are 1-3/8" to 1-3/4".
• After installation there will be only a 3/32" gap between the door and frame.
• Hinge is 4" tall. Width of leaf (not including barrel of hinge) is 1-3/4". Thickness of hinge is 3/32".
• Base material is steel for the brass and oil rubbed bronze finishes.
• The base material of the stainless steel hinge is stainless steel.
• The ball bearings in all of the hinges are made of stainless steel.
• Each hinge uses 8 each #8 screws. Screws are included with hinge.
• These hinges are sold by the "Each". You would normally order 2 or 3 hinges per door.

Finishes:

• Satin Stainless Steel
• Brass Plated
• Oil Rubbed Bronze

• Loose joint hinge, opened door may be lifted off after installation.
• Available in either a "Left Hand" or a "Right Hand" model.
• Made from stainless steel (Type 304) with a satin stainless steel finish.
• Available in a 4 x 4 inch model or a 4.5 x 4.5 inch model.
• Hinge thickness is 0.14".
• Hinge pin is 11/32" in diameter.
• Stainless steel wood screws are included.

• Hinge measures 4-1/2" high by 4" wide
• Loose joint hinge, opened door may be lifted off after installation
• Comes in either a right hand or left hand model
• Steel base material, comes complete with matching #12 wood screws
• Hinge thickness is .139". Hinge Pin diameter is .308".

Finishes:

• Satin Chrome
• Oil Rubbed Bronze
• Prime Coated

• Pocket pivot hinge is also known as a Harmon hinge.
• This unique hinge is a "swing clear" type of hinge that allows a door to swing into a pocket at a right angle to the door frame.
• When the door is in the pocket it is completely clear of the door opening.
• The base material is made from solid stainless steel.
• Not handed, full mortise installation.
• Maximum door swing is 90 degrees.
• For doors weighing up to 270 lbs. use 3 hinges. For doors weighing up to 360 lbs use 4 hinges.
• Matching fasteners are included.
• PLEASE NOTE: THESE HINGES ARE A SPECIAL ORDER ITEM. THEY ARE PRODUCED AT THE TIME OF ORDER. THEY ARE NOT RETURNABLE AND THE LEAD TIME IS ABOUT 3-4 WEEKS.

Finishes:

• Polished Brass (US3)
• Satin Stainless Steel (US32D)
• Satin Bronze (US10)
• Polished Stainless Steel (US32)
• Oil Rubbed Bronze (US10B)