• For 1-1/8" to 1-3/8" thick doors
• Reversible (non-handed) for Right Hand or Left Hand installations
• For doors up to 60" high (75lb maximum weight)
• For overlay type installations
• Made from 0.125" steel
• Wood screws are included
• Horizontal piece (as shown in photo) measures 2-1/2" x 1"
• Vertical flat piece (which mounts to wall) measures 3" x 7/8"
• Rounded piece projects from wall 2-1/2"
• Sold by the pair. A pair is what is required to install one door.

Finishes:

• Satin Chrome
• Polished Brass

• For 1-1/8" to 1-3/8" thick door.
• Heavy duty pivot hinge can be used for flush, recessed, or overlay type installations.
• These pivot hinges are handed (Right Hand or Left Hand). Hinge in photo shows Left Hand set.
• Made from 0.127" steel
• Wood screws are included
• Approximate measurements for top pivot: 2-1/2" long, 2-3/8" wide and 1" tall.
• Approximate measurements for bottom pivot; 2-1/2" long, 2-5/16" wide and 1-1/2" tall.
• Complete instructions are included.
• Sold by the pair. A pair is what is needed to install one door.

Finishes:

• Satin Chrome
• Polished Brass

• For 1-1/8" to 1-3/8" thick door.
• Heavy duty pivot hinge can be used for flush or recessed type installations.
• These pivot hinges are handed (Right Hand or Left Hand). The hinge in the photo shows a Left Hand hinge.
• Made from 0.125" steel.
• Wood screws are included.
• Approximate measurements for top pivot; 2-1/2" long by 2-1/8" wide.
• Approximate measurements for bottom pivot; 2-1/2" long by 3" tall by 2-1/8" wide.
• Complete instructions are included.
• Sold by the pair. A pair is what is needed to install one door.

Finishes:

• Satin Chrome
• Polished Brass

• For doors up to 159 lbs
• For overlay doors 1-3/8" to 1-3/4" thick
• Doors can be installed floor to ceiling
• Full 180 degree opening
• Made from 0.182" steel
• Extra long screws are included
• Horizontal piece (as shown in photo)measures 3" by 1-1/2"
• Vertical flat piece (which mounts to wall) measures 3" x 1-1/8"
• Rounded piece projects from wall 3"
• Sold by the pair. A pair is what is needed to install one door.

Finishes:

• Satin Chrome Plated (US26D)

• variable overlay
• for 3/4" doors
• for left- or right-hand doors
• flat head wood screws (#6 x 5/8") included
• elongated screw holes for adjustment during installation
• steel base material

Finishes:

• Zinc Plated
• Burnished Brass

• 23/32" overlay
• for 3/4" doors
• for left- or right-hand doors
• flat head wood screws (#6 x 5/8") included
• elongated screw holes for adjustment during installation
• steel base material

Finishes:

• Zinc Plated
• Burnished Brass

• Steel base material.
• Size of each hinge is 1/8" thick, 3/8" wide, 2-1/4" long.
• Each hinge uses 6 each #4 flat head screws (not included but offered for purchase during checkout). Order our SKU #286253.

Finishes:

• Bronze plated

• Right angle or "L" type pivot hinge.
• Allows doors to be set back and swing clear of corner posts.
• Hinge is handed and sold by the pair. You will receive one "left hand" and one "right hand" hinge for each pair ordered.
• Steel base material.
• Uses #4 flat head wood screws (not included but offered for purchase during checkout). Order our SKU 286253 for #4 x 5/8 bronze flat head wood screws. Order 8 screws for each pair of hinges ordered.
• For dimensions click on link below

Finishes:

• Bronze

• Pivot hinge has two parts a leaf and pivot pin and a metal cup which holds the pivot pin.
• The leaf measures 2" by 3/8" by 1/8" thick.
• The cup is 3/8" tall by 3/8" in diameter.
• Steel base material.
• Uses a #5 flat head wood screw (not included but offered for purchase during checkout)
• Order our SKU #286254 #5 x 5/8" bronze wood screw for this hinge. Each hinge takes 2 wood screws.

Finishes:

• Bronze

• Rear pivot hinge is made up of a wrap around leaf with a pivot pin and a knurled metal cup that holds the pivot pin.
• The wrap around leaf measures 2" by 7/16" with a about a 1/2" distance to the wrap around.
• The knurled metal cup is about 3/8" in diameter and fits in a 1/4" deep drilled hole.
• The wrap around leaf mounts to the back of the door.
• This hinge uses 2 each #6 x 5/8" Round Head Bronze plated screws per hinge (not included but offered for purchase during checkout). Order our SKU 286252 if you need screws.
• Steel base material.

Finishes:

• Bronze

• Made for overlay cabinet doors up to 1" thick
• Hinge pivots 270 degrees
• The plate that attaches to the cabinet measures 1-1/4" x 1". The plate that attaches to the door measures 1-3/8" x 7/8". The pivot point projects out 1-7/16" from the cabinet surface
• Steel base material
• Screws not included
• Uses 12 each #6 screws per pair of hinges(not included). We have not been able to find an exact finish match for the screws. We offer solid brass screws upon checkout which is fairly good match for the finish but not an exact match.

Finishes:

• Antique Brass

• Pivot hinge is made for use with 3/4" or 7/8" material.
• Made from Type 430 stainless steel.
• Natural finish.
• Uses #5 flat head wood screws (not included)
• Picture shown is right hand model.
• When ordering hinges for your door order either 2 left hand hinges for the same door or two right hand hinges for the same door.

• Hinge can be used for trash receptical doors, pet doors or any small pivot door.
• Made from steel base material.
• Concealed pivot hinge is for inset doors with a maximum door thickness of 1".
• Drill 7mm (9/32") hole for plastic bushing.
• Pan head wood screws are included.

Finishes:

• Black

• For large cabinet doors and full size doors
• Made of solid brass with steel pins
• Flat head wood screws are included
• For SKU numbers 838198 to 838242 the pivot screw is flush with the hinge (as shown in photo to left).
• For SKU numbers 838250 to 838252, the pivot screw has a raised slotted head which measures about 3/4" in diameter and is 3/16" above the hinge surface. This large pivot hinge pivots on roller bearings. A pivot base is available for these 3 SKU numbers only. It is offered for purchase during checkout.
• For tall doors an intermediate pivot hinge is recommended to keep the middle part of the door in alignment. Our SKU's 838204 through 838206 will work with any of the pivot hinges in this section. Intermediate pivots are offered for purchase during checkout.
• The listed weight ratings are for a pair of hinges.

Finishes:

• Polished Brass
• Satin Nickel
• Oil Rubbed Bronze

• This pivot base is used with our Large Pivot Hinges (SKU numbers 838250, 838251 and 838252 only).
• The pivot base replaces one leg of the pivot hinge (the non-door leg) to allow an easier installation if installing in concrete, marble, stone or any other material where a smaller cutout is desired.
• Pivot base measures approximately 1.25" in height by 1" in diameter at the top and 3/4" in diameter at the bottom.
• Made from solid brass.

Finishes:

• Polished Brass
• Oil Rubbed Bronze
• Satin Nickel

• These intermediate pivots work only with our pivot hinges in the SKU range from 838198 to 838252.
• An intermediate pivot hinge is used for taller doors to keep the middle part of the door in alignment with the pivot hinges at the top and bottom of the door.
• Made from solid brass material.
• Includes matching wood screws.
• Each hinge leaf measures 2-1/2" tall by 1-1/4" wide by 5/16" thick. Total width of hinge including hinge barrel is 2-1/2".

Finishes:

• Satin Nickel
• Polished Brass
• Oil Rubbed Bronze

• Small spring loaded pivot hinge for inset doors
• The hinge is made of two parts; a spring loaded pin housing and a plastic bushing (pin receiver)
• Both hinge parts install by drilling a hole and press fitting them in place
• The spring loaded pin housing measures 1-3/8" long by 1/4" diameter. The pin diameter is 5/32" and projects 1/4"
• The plastic bushing is 7/16" in outside diameter
• Maximum door opening is approximately 140 degrees
• This hinge will work on door thicknesses ranging from 1/2" to 13/16"
• This hinge is made of plastic with a steel pin and spring.
• Hinge is sold by the pair. Order 1 pair per door.
• Tab adjustment screw is not included.
• PLEASE NOTE: This hinge is not a "self-closing" hinge. The spring is in the pin receiver and is meant only to keep the pin in place after installation.

Finishes:

• Black Plastic

• Semi-concealed pivot hinge, only the tip shows through from the cabinet front.
• To install cut an angled 7/32" slot through the edge of the door.
• For door thickness of 5/8" to 3/4"
• Door opens 270 degrees when installed on a 5/8" door.
• Door opens 255 degrees when installed on a 3/4" door.
• Hinges measures approximately 1-3/4" tall and 2" wide as shown in photo.
• This hinge is sold by the pair. A pair includes a top hinge (as shown in photo) and a bottom hinge. The hinges are not handed, they will work on both a left hand and right hand door.
• Steel base material.
• Uses #6 Oval Head wood screws (not included). Order our SKU #400993 for a screw in an oil rubbed bronze finish that is a good match. Order 12 screws per pair of hinges. Screws are offered for purchase during checkout.

Finishes:

• Dark Bronze Plated

• This hinge is for a full overlay door with no cabinet face frame.
• Works on door thicknesses up to 3/4"
• Wrap around feature assures that all screws go into solid wood rather than end grain
• Small leaf measures 2" by 3/8"
• Large leaf measures approximately 1-7/8" by 1-1/8".
• Hinge is sold by the pair. A pair includes a top pivot and a bottom pivot.
• Photo shows the top pivot
• Product uses 12 each #5 Flat Head wood screws per pair of hinges(not included but offered for purchase during checkout). Order our #5 x 5/8" Bronze plated flat head wood screw SKU # 286254.
• Steel base material.

Finishes:

• Bronze

• For cabinets with a face frame
• Steel base material with plastic spring mechanism
• Matching wood screws are included
• SKU number 399955 is for a 3/8" partial inset door
• SKU numbers 399950, 399960 and 399965 are for overlay doors
• These hinges are not handed
• If you are trying to match an existing hinge look for the style number stamped on your hinge.

Finishes:

• Burnished Brass

• Overlay door pivot hinge, made from Type 430 stainless steel.
• IMPORTANT, PLEASE NOTE; These hinges are "handed". Order one left hand (SKU 658003)and one right hand hinge (SKU 658017) for each door you are installing.
• PLEASE NOTE; the handing refers to where the hinge is located not whether the door is a left hand or right hand door. If you order a left hand hinge and a right hand hinge you can hinge either a right hand door or a left hand door.
• Made for 3/4" thick doors.
• May be used as a 270 degree hinge if the pivot point is located just outside of the cabinet corner.
• Each hinge uses 6 each #8 flat head screws. Not included but offered for purchase during checkout.

Finishes:

• Stainless Steel, Natural

• Pivot hinge is made for 3/8" partial inset doors (also known as 3/8" inset doors with a 3/8" lip)
• Made for use on 3/4" thick doors.
• Sold as a pair which includes a left hand hinge (marked with a "L") and a right hand hinge (marked with a "R")
• If the hinges are used on horizontally swinging doors the left hand hinge is used as the top pivot and the right hand hinge is used as the bottom pivot.
• The photo to the left shows the "Left Hand" hinge. The bottom leaf attaches to the edge of the face frame. The top leaf attaches to the back of the door.
• The pivot point of the hinge installs in a 1/4" slot cut in the lip of the door from the backside of the door.
• If you are replacing old hinges your hinge should have the number "1247" stamped on it (usually not visible when the hinge is installed).
• Matching wood screws are included (8 screws per pair). Made from steel base material.

Finishes:

• Burnished Brass

• Pivot hinge for windows and cabinet doors allows door to pivot up to 360 degrees depending on installation of door in frame.
• Hinge is 4-5/8" long by 7/8" wide.
• Hinge is 9/16" thick at thickest point.
• The gap between the two leaves is 1/16". Hinge may be mortised into the bottom of the door and the frame for a minimum gap.
• Made from 1/8" thick material.
• Hinge pivots on an oilite, self-lubricating bearing.
• Flat head wood screws are included.
• Available in two models; solid brass or steel.
• These hinges are sold by the pair (2 hinges) which is normally what you need to hinge one door.

Finishes:

• Steel, yellow zinc chromate plated
• Solid Brass, natural, unfinished.

• Pivot hinges made from Type 430 stainless steel.
• These pivot hinges are available in both Left Hand and Right Hand models and are available in two sizes.
• May be used as 270 degree hinges if the pivot point is located just outside of the cabinet corner.
• Available in two sizes; the small size fits up to a 11/16" thick door, the large size fits up to a 7/8" thick door.
• For each door you are hinging order one left hand hinge and one right hand hinge.
• Each hinge uses 4 to 6 each #4 flat head screws, not included but offered for purchase during checkout.

Finishes:

• Natural Stainless Steel