Stainless Steel Chest & Box Hardware

Stainless Steel Chest & Box Hardware

Hardware for chests and boxes made from stainless steel.

Lid Support, Stainless Steel

Lid Support, Stainless Steel
  • Lid Stay or Support for boxes, cedar chests, blanket chests, etc.
  • This lid support assists in the lifting of your lid and it will hold the lid in the "up" position.
  • PLEASE NOTE: this lid support does not "dampen" the closing action of the lid so it is not recommended for children's toy boxes.
  • Made from stainless steel and nylon with a stainless steel spring.
  • Available in 3 different mounting styles (all models mount on inside of box)
    • Right Side Mount (mounts on underside of lid and right side panel of box)
    • Left Side Mount (mounts on underside of lid and left side panel of box)
    • Back Wall Mount (mounts on underside of lid and back wall of box)
  • Available in two different weight ratings (use formula information below to calculate your lid "moment")
    • 26 inch/pounds (in/lbs) maximum lid moment
    • 34 inch/pounds (in/lbs) maximum lid moment
  • Click on PDF link below for product dimensions and exact installation locations. Dimensions are in millimeters.
  • Important information about the hinge location and back wall thickness of your box. For this lid support to work correctly, the back wall of your box must be 3/4" thick and the pivot point of your hinge (where the hinge pin is) must be located on the outside back wall of the box. See PDF link for more information. Normally, you would use a piano hinge or several butt hinges to hinge your lid.
  • The formula for the weight rating is: Lid Front to back dimension (in inches) times Lid Weight in pounds divided by 2 equals the lid "moment".
  • More than one lid support can be used for heavier lids, up to 3 supports per lid. Do not mix lid supports of different weight ratings when using more than support.
  • Do the calculation using the formula and choose the lid support that most closely matches the "moment" of your lid. Do not exceed the maximum rating value.
  • IMPORTANT:
    • Screws are not included and must be ordered separately. Order 4 each #8 pan head stainless steel screws per lid support. The are offered for purchase during checkout.
    • Instructions are not included. Please print out the PDF file so that when your supports are delivered you will have instructions.
Click here for Information & Pricing

Draw Pull Catch, Stainless, 6"

Draw Pull Catch, Stainless, 6
  • Draw-pull catch for chests, tool boxes, toy boxes, etc.
  • Made from stainless steel.
  • Catch tension is adjustable by means of a threaded piece and locknut (1/2" of adjustment).
  • Catch measures 6" tall by 1-1/2" wide.
  • Catch can be locked with a padlock (padlock not included).
  • Each catch uses 2 each #6 flat head screws and 2 each #8 flat head screws. Screws are not included but are offered for purchase during checkout.

Finishes:

  • Natural Stainless Steel
Click here for Information & Pricing

Draw Pull Catch, Stainless, 2-3/4"

Draw Pull Catch, Stainless, 2-3/4
  • Draw-pull catch for chest, tool boxes, toy boxes, etc.
  • Made from stainless steel.
  • Catch measures 2-3/4" tall by 1-1/8" wide.
  • Available in two models; SKU 702018 has a padlock eye so the catch can be locked (padlock not included). SKU 702016 is identical but has no eye. Photo to left shows SKU 702018.
  • Each catch uses 4 each #4 pan head screws (not included but offered for purchase during checkout).

Finishes:

  • Natural Stainless Steel
Click here for Information & Pricing

Draw Pull Catch, Stainless, 4"

Draw Pull Catch, Stainless, 4
  • Draw-pull catch for chests, tool boxes, toy boxes, etc.
  • Made from stainless steel.
  • Catch tension and throw is adjustable by means of a threaded piece. Throw adjustment is approximately 1-1/4".
  • Catch measures approximately 4-1/2" by 7/8" when set at maximum and 3-1/4" by 7/8" when set at minimum.
  • Each catch uses 4 each #6 flat head screws. Not included but offered for purchase during checkout.

Finishes:

  • Natural Stainless Steel
Click here for Information & Pricing

Draw Pull Catch, Stainless, 2-1/4"

Draw Pull Catch, Stainless, 2-1/4
  • Stainless steel draw pull catch for tool boxes, tackle boxes, toy boxes, small chests, etc.
  • Catch measures 2-1/4" by 1".
  • Made from stainless steel.
  • Each catch uses 4 each #4 pan head screws. Not included but offered for purchase during checkout.

Finishes:

  • Polished Stainless Steel
Click here for Information & Pricing

Draw Pull Catch, Stainless, 2-1/8"

Draw Pull Catch, Stainless, 2-1/8
  • Stainless steel draw pull catch for tool boxes, tackle boxes, toy boxes, small chests, etc.
  • Catch measures 2-1/8" by 1-1/4".
  • Made from stainless steel.
  • Each catch uses 4 each #4 pan head screws. Not included but offered for purchase during checkout.

Finishes:

  • Stainless Steel
Click here for Information & Pricing

Chest Handle, Stainless Steel

Chest Handle, Stainless Steel
  • Stainless steel handle for chests.
  • Handle measures 4-1/4" wide by 2-7/8" tall. Flip up handle projection is 2-5/16".
  • Uses 4 pan head #8 screws per handle (not included but offered for purchase during checkout).
  • Handle comes in a raw industrial type finish.

Finishes:

  • Natural Stainless Steel (unpolished)
Click here for Information & Pricing

Hasp, Stainless Steel

Hasp, Stainless Steel
  • Stainless steel hasp accepts padlock for locking gates, boxes, chests, doors, cabinets, etc.
  • Made from Type 304 stainless steel.
  • Available in 4 sizes; Large, Medium, Small and Extra Small.
  • Stainless steel screws are included.
  • Padlock eye rotates 360 degrees. When a padlock is attached the padlock eye is held in the vertical position (via gravity) to help secure the hasp.

Finishes:

  • Polished Stainless Steel
Click here for Information & Pricing