Solid Bronze Gate Hardware

Solid Bronze Gate Hardware

  • Solid bronze hardware is great for coastal areas
  • Or anywhere the look of a rustic old world design is desired.
  • There are over 70 different solid bronze products in this section.

Solid Bronze Deadbolt

Solid Bronze Deadbolt
  • Solid Bronze Dead Bolt for gates and doors.
  • Construction:
    • All outside trim pieces are solid cast bronze.
    • Keyed cylinder, screws, strikeplates, keys and a few internal parts are solid brass
    • The latch, internal security plate, and security screwsare made of steel and some die cast parts.
    • Included is a plastic dust cover that goes behind the strikeplate on the door or gate
  • Features:
    • Single cylinder dead bolt
    • Keyed cylinder on one side and a turn knob on the other
    • Uses a Schlagekeyway, cylinder can be keyed by your locksmith to otherSchlage type locks in your house
    • The typical installation of a single cylinderdead boltwill have the knob on the inside of the door or gate and the keyed cylinder on the outside.
    • 1" bolt throw
    • All fasteners necessary for installation are included.
  • Available in two trim plate sizes:
    • Small Trim Plate Model (SKU 850036)
      • Knob trim plate measures 2" wide by 2-1/2" tall
      • Knob trim plate projection is 1-1/2"
      • Cylinder trim plate measures 2" wide by 2-9/16" tall
      • Cylinder trim plate projection is 7/8"
    • Large Trim Plate Model (SKU 850034)
      • Knob trim plate measures 2-1/2" wide by 2-7/8" tall
      • Knob trim plate projection is 1-1/2"
      • Cylinder trim plate measures 2-7/8" wide by 3-1/16" tall
      • Cylinder trim plate projection is 1"
  • Installation:
    • Backset is2-3/8"
    • The Backset is the measurement from the edge of the door to the center of the cylinder hole in the door.
    • Fits door thicknesses from 1-3/4" to 3".
    • Bore dimension for the cylinder is a minimum 1-3/4".
    • Bore dimension for the latch is 1".
    • Works on both Left Hand and Right Hand opening doors.

Please note: These locks can be special ordered to accomodate up to a 3-1/2" door thickness and with 2-3/4" backsets. Please call our office for information.

Click here for Information & Pricing

H Hinge, Solid Bronze

H Hinge, Solid Bronze
  • Solid bronze H-hinge for use in coastal areas or anywhere a rustic old world design is desired.
  • From our "Solid Bronze Collection".
  • Hinge is approximately 7" tall by 5" wide. Hinge thickness is approximately 1/4".
  • Hinge barrel is approximately 7/8" in diameter.
  • Hinge is designed to be surface mounted and is not swaged.
  • This beautiful and unique hinge will work well for any high-end gate or entrance door.
  • 5/16" x 1-1/2" Bronze colored stainless steel hex bolts are included.
Click here for Information & Pricing

Solid Bronze Tee Hinge

Solid Bronze Tee Hinge
  • This very high quality solid bronze tee hinge is made for use in coastal areas or anywhere a rustic old world design is desired. From our "Solid Bronze Collection".
  • Bronze is an old world material that does not deteriorate in coastal or other regions. The Bronze finish, however, is a "living" finish. Please read more about this by clicking on the link.
  • Great for use on exterior gates and barns.
  • Includes 9 each #8 x 1-1/4" matching wood screws.
Click here for Information & Pricing

Solid Bronze Full Mortise Butt Hinge

Solid Bronze Full Mortise Butt Hinge
  • These solid bronze Architectural Grade hinges are an alternative to surface mounted strap hinges. Architectural Grade butt hinges are thicker and of much higher quality than Residential Grade butt hinges.
  • These hinges are installed on gates as "full mortise butt hinges" just as hinges are installed on the typical front door of a house. For a more decorative look, surface mount "dummy strap" hinges on the front of your gate.
  • The 3" & 3-1/2" hinges come with wood screws.
  • The 4" and larger hinges come with wood screws and machine screws.
  • They are made of solid bronze base material with a solid bronze hinge pin.
  • Optional finials are available for most hinges, check our "Finials & Ball Tips for Door Hinges" section for either Type A or Type B finials.

*NRP HINGES (non-removable pin) have a set screw in the barrel that is accessible only when door is swung open. This security feature deters someone from removing the hinge pin and the door. NRP hinges are normally used for exterior doors that open out.

PAIR or EACH. Please note the UNIT when ordering hinges. We sell the hinges depending on how the manufacturer sells them to us. In this section if a hinge is sold by the PAIR you may order by the half pair. For example if you want 3 hinges order 1.5 pair when you check out. If the hinge is sold by the EACH and you need 3 hinges then order 3 EACH.

Finishes:

  • 613 (US10B) oil rubbed bronze
Click here for Information & Pricing

4 x 4 Solid Bronze Button Tip Hinge

4 x 4 Solid Bronze Button Tip Hinge
  • Beautiful solid bronze butt hinge for use in coastal areas or anywhere a rustic old world design is desired.
  • Hinge features button tips. Hinge measures 4" by 4" (in the flat open position) and is 1/4" thick.
  • Hinge is not swaged.
  • This hinge matches other products from our "Solid Bronze Collection".
  • Matching flat head wood screws are included.
  • Bronze is an old world material that does not deteriorate in coastal or other regions. The Bronze finish, however, is a "living" finish. Please read more about this by clicking on the link.
  • ADVISORY: This hinge is not an Architectural grade hinge (template hinge) and will not match the exact size and screwhole patterns of a template hinge. This hinge is cast bronze and as such the size and screw hole patterns will vary slightly between products. It is advisable to wait until you have the product in hand before you cut hinge mortises in your door and door jamb.
  • If you would like a solid bronze Architectural Grade Template hinge please see our SKU # 307700.
  • This hinge is sold by the Each. You will normally order 2 or 3 (or sometimes more) hinges per door.

Finishes:

  • Solid Natural Bronze
Click here for Information & Pricing

4 x 4 Solid Bronze Ball Tip Hinge

4 x 4 Solid Bronze Ball Tip Hinge
  • Beautiful solid bronze butt hinge for use in coastal areas or anywhere a rustic old world design is desired.
  • Hinge features ball tips. Hinge measures 4" by 4" (in the flat open position) and is 1/4" thick.
  • Hinge is not swaged.
  • This hinge matches other products from our "Solid Bronze Collection".
  • Matching flat head wood screws are included.
  • Bronze is an old world material that does not deteriorate in coastal or other regions. The Bronze finish, however, is a "living" finish. Please read more about this by clicking on the link.
  • ADVISORY: This hinge is not an Architectural grade hinge (template hinge) and will not match the exact size and screwhole patterns of a template hinge. This hinge is cast bronze and as such the size and screw hole patterns will vary slightly between products. It is advisable to wait until you have the product in hand before you cut hinge mortises in your door and door jamb.
  • This hinge is sold by the Each. You will normally order 2 or 3 (or sometimes more) hinges per door.

Finishes:

  • Solid Natural Bronze
Click here for Information & Pricing

4 x 4 Solid Bronze Steeple Tip Hinge

4 x 4 Solid Bronze Steeple Tip Hinge
  • Beautiful solid bronze butt hinge for use in coastal areas or anywhere a rustic old world design is desired.
  • Hinge features steeple tips. Hinge measures 4" by 4" (in the flat open position) and is 1/4" thick.
  • Hinge is not swaged.
  • This hinge matches other products from our "Solid Bronze Collection".
  • Matching flat head wood screws are included.
  • Bronze is an old world material that does not deteriorate in coastal or other regions. The Bronze finish, however, is a "living" finish. Please read more about this by clicking on the link.
  • ADVISORY: This hinge is not an Architectural grade hinge (template hinge) and will not match the exact size and screwhole patterns of a template hinge. This hinge is cast bronze and as such the size and screw hole patterns will vary slightly between products. It is advisable to wait until you have the product in hand before you cut hinge mortises in your door and door jamb.
  • This hinge is sold by the Each. You will normally order 2 or 3 (or sometimes more) hinges per door.

Finishes:

  • Solid Natural Bronze
Click here for Information & Pricing

Strap Hinge System, Solid Bronze

Strap Hinge System, Solid Bronze
  • This very high quality solid bronze strap hinge is made for use in coastal areas or anywhere a rustic old world design is desired. From our "Solid Bronze Collection".
  • This product is sold in components. The components consist of 2 items; a "Strap" which attaches to the gate surface and a pintle which attaches to the post. The pintle is available as either a "Plate Pintle" a "Screw-in Pintle" or a "Jam Pintle".
  • The "Plate Pintle" measures 2" wide by 6-1/4" tall. The plate material is about 1/4" thick. The pintle portion is 11/16" in diameter by 2" tall.
  • The "Screw-In Pintle" is available in two sizes, Small and Large. The small size measures 5" horizontally and 3-3/8" vertically. The pintle portion is 11/16" in diameter by 2" tall. The screw thread portion is 3-1/4" by 11/16". The large size measures 7.5" horizontally and 3-7/8" vertically. The pintle portion is 11/16" in diameter by 2" tall. The screw thread portion is 6" by 13/16".
  • The "Jam Pintle" is meant to be installed in the jamb or edge of the door frame or gate post and can be installed in a mortise (cutout). The mounting plate portion of the "Jam Pintle" measures 4-3/4" wide by 2-7/16" tall by 9/32" thick. The pintle is 2" tall by 11/16" in diameter. It is available in a Right Hand Model and a Left Hand Model. The image in the photo shows a Right Hand Model. Here is how the handing works: Go to the side of the gate or door where the hinges are visible (the hinged side of the door), stand with your back against the gate or door. If you want the hinges on your right then you should order the Right Hand Model. If you want your hinges on your left then you should order the Left Hand Model.
  • Lag screws (1-1/2" long)are included for the "Plate Pintle", flat head wood screws are included for the "Jam Pintle". Screws are made from stainless steel and coated black.
  • Two hinges will support a 150 lb. gate or door. Three hinges will support a 250 lb. gate or door.
  • Bronze is an old world material that does not deteriorate in coastal or other regions. The Bronze finish, however, is a "living" finish. Please read more about this by clicking on the link.

Finishes:

  • Natural Solid Bronze
Click here for Information & Pricing

12 Inch Band Hinge and Pintle Plate, Solid Bronze

12 Inch Band Hinge and Pintle Plate, Solid Bronze
  • Solid bronze strap hinge for use in coastal areas or anywhere a rustic old world design is desired. From our "Solid Bronze Collection".
  • Hinge strap measures approximately 12" in length. Width of hinge strap is 1-1/4". Thickness of strap is approximately 5/16".
  • Pintle plate measures 3-3/4" by 1-1/4".
  • Stainless steel wood screws are included. Screws are coated with a matching bronze finish.
  • Bronze is an old world material that does not deteriorate in coastal or other regions. The Bronze finish, however, is a "living" finish. Please read more about this by clicking on the link.
  • PLEASE NOTE: This hinge is made up of two parts that must be ordered separately; the pintle plate and the hinge strap. Please make sure to order one pintle plate and one hinge strap to make up each hinge that you intend to order.
Click here for Information & Pricing

18" Solid Bronze Strap Hinge

18
  • This very high quality solid bronze strap hinge is made for use in coastal areas or anywhere a rustic old world design is desired. From our "Solid Bronze Collection".
  • Vertical mounting plate measures 6-1/2" tall by 2-3/32" wide. Thickness of plate is 1/4". Hinge barrel is 1-1/2" in diameter.
  • Horizontal strap measures 18" from tip of strap to end of hinge barrel. Width of strap is 2". Thickness of strap is 1/4" to 3/8" (strap is thicker in middle than on edges).
  • Bronze is an old world material that does not deteriorate in coastal or other regions. The Bronze finish, however, is a "living" finish. Please read more about this by clicking on the link below
  • This hinge is sold by the each. You would normally order 2 or 3 hinges per door or gate.
  • Uses 5/16" square head lag screws. Lag screws are included with hinge. Lag Screws are made from stainless steel and coated with a bronze colored coating.
  • PLEASE NOTE: this hinge is "handed", available in a Right Hand model and a Left Hand model. The hinge shown in the photo is the Right Hand model (SKU 850222).

Finish

  • Natural Solid Bronze
Click here for Information & Pricing

Mason Pintle & Strap Hinge

Mason Pintle & Strap Hinge
  • This very high quality solid bronze strap hinge is made for use in coastal areas or anywhere a rustic old world design is desired. From our "Solid Bronze Collection".
  • This product is sold in components. The components consist of 2 items; a strap hinge which attaches to the gate surface and a masonary pintle which is cemented into a masonary wall (for example block or stone) or post.
  • Lag screws are included with the strap hinge. The Lag Screws are made from stainless steel and coated black. Lag Screws are available in two lengths (1.5" or 2.5"). Please specify which length you prefer in the "Comment" section when you checkout.
  • The masonary pintle measures approximately 13.5" long by 1-1/8" in diameter. The pintle is 2.25" tall by 11/16" in diameter. The masonary pintle is made of solid brass and may be cut down in length by the end user if necessary.
  • Two hinges will support a 150 lb. gate or door. Three hinges will support a 250 lb. gate or door.
  • Bronze is an old world material that does not deteriorate in coastal or other regions. The Bronze finish, however, is a "living" finish. Please read more about this by clicking on the link.

Finishes:

  • Straps are Natural Solid Bronze
  • Masonary Pintle is solid brass
Click here for Information & Pricing

Screw-In Pintles, Solid Bronze

Screw-In Pintles, Solid Bronze
  • This very high quality solid bronze product is made for use in coastal areas or anywhere a rustic old world design is desired. From our "Solid Bronze Collection".
  • Available in two sizes: Small and Large
  • The Small size measures 5" horizontally and 3-3/8" vertically. The pintle portion is 11/16" in diameter by 2" tall. The screw thread portion is 3-1/4" by 11/16".
  • The Large size measures 7.5" horizontally and 3-7/8" vertically. The pintle portion is 11/16" in diameter by 2" tall. The screw thread portion is 6" by 13/16".
  • The "Screw-In Pintle" is used with the strap hinges from our "Solid Bronze Collection" (SKU numbers 850022, 850024, 850026, 850028).
  • The "Screw-In Pintle" is meant to screw into a wooden gate post.
  • Bronze is an old world material that does not deteriorate in coastal or other regions. The Bronze finish, however, is a "living" finish. Please read more about this by clicking on the link.
Click here for Information & Pricing

Solid Bronze Dummy Strap

Solid Bronze Dummy Strap
  • Solid bronze dummy strap hinge for use in coastal areas or anywhere a rustic old world design is desired. From our "Solid Bronze Collection".
  • Dummy straps provide a decorative strap look to a gate or door hinged with full mortise butt hinges.
  • Available in two lengths. Both sizes are made from 1/4" thick material. Both sizes are 2" wide and measure 4" at the widest part.
  • Stainless steel lagscrews are included. Lag screws are coated with a finish that matches the bronze finish.
  • Bronze is an old world material that does not deteriorate in coastal or other regions. The Bronze finish, however, is a "living" finish. Please read more about this by clicking on the link.

Finishes:

  • Solid Natural Bronze
Click here for Information & Pricing

Dummy Strap, Solid Bronze

Dummy Strap, Solid Bronze
  • Dummy straps install on the face of any door or gate to give the look of a decorative strap hinge. They are normally used in combination with full mortise butt hinges.
  • Dummy straps made of solid bronze are for use in coastal areas or anywhere a rustic old world design is desired. From our "Solid Bronze Collection".
  • Matching wood screws are included.
  • These beautiful dummy straps are available in 6 lengths.
  • Bronze is an old world material that does not deteriorate in coastal or other regions. The Bronze finish, however, is a "living" finish. Please read more about this by clicking on the link.

Finishes:

  • Solid Natural Bronze
Click here for Information & Pricing

Slide Bolt, Solid Bronze, 4 Inch

Slide Bolt, Solid Bronze, 4 Inch
  • Solid bronze slide bolt for use in coastal areas or anywhere a rustic old world design is desired. From our "Solid Bronze Collection".
  • Slide bolt is designed to be surface mounted.
  • Measures approximately 5 inches in length including strike plate. Width is 1-1/2". Projection is 3/4".
  • Stainless steel screws are included. They are coated with a matching bronze finish.
  • Bronze is an old world material that does not deteriorate in coastal or other regions. The Bronze finish, however, is a "living" finish. Please read more about this by clicking on the link.
Click here for Information & Pricing

Solid Bronze Surface Bolt, 8 Inch

Solid Bronze Surface Bolt, 8 Inch
  • Solid bronze surface bolt for use in coastal areas or anywhere a rustic old world design is desired. From our "Solid Bronze Collection".
  • Surface bolt measures 8" long by 1-3/4" wide.
  • Wood screws are included.
  • Bronze is an old world material that does not deteriorate in coastal or other regions. The Bronze finish, however, is a "living" finish. Please read more about this by clicking on the link.

Finishes:

  • Natural Bronze
Click here for Information & Pricing

Solid Bronze Gate Stop

Solid Bronze Gate Stop
  • Solid bronze gate stop will stop gate in the closed position. The installation of a gate stop prevents damage to your gate latch by stopping the gate before it hits the latch bar. Bronze latch bars will become weakened and eventually break if gates are allowed to slam against them.
  • Gate stop measures 2" tall by 2" wide with a 1.5" projection.
  • Mounting screws are included.
  • Bronze is an old world material that does not deteriorate in coastal or other regions. The Bronze finish, however, is a "living" finish. Please read more about this by clicking on the link.

Finishes:

  • Natural Solid Bronze
Click here for Information & Pricing

Drop Bar Latch, Solid Bronze

Drop Bar Latch, Solid Bronze
  • Solid Bronze Drop Bar Latch for Gates
  • This solid bronze gate latch is greatfor use in coastal areas or anywhere a rustic old world design is desired.
  • From our "Solid Bronze Collection".
  • Latch surface mounts on the gate and post.
  • Overall dimensions of latch are approximately 2" tall by 5" wide.
  • Comes with matching stainless steel wood screws.
  • Bronze is an old world material that does not deteriorate in coastal or other regions. The Bronze finish, however, is a "living" finish. Please read more about this by clicking on the link.
Click here for Information & Pricing

Barrel Bolt, Solid Bronze

Barrel Bolt, Solid Bronze
  • Solid bronze barrel bolt is lockable with a padlock (padlock not included).
  • Bolt measures 8" long by 5/8" diameter.
  • Handle measures 4".
  • Mounting brackets are 1-3/4" by 3/4".
  • Barrel bolt surface mounts to gate or door.
  • Bronze is an old world material that does not deteriorate in coastal or other regions. The Bronze finish, however, is a "living" finish. Please read more about this by clicking on the link.

Finishes:

  • Natural Bronze
Click here for Information & Pricing

Ring Turn Bar Latch, Solid Bronze

Ring Turn Bar Latch, Solid Bronze
  • Very high quality Ring Turn Bar Latch for gates and doors.
  • Latch operates from both sides of the gate.
  • Made from solid bronze and is made for use in coastal areas or anywhere a rustic old world design is desired. From our "Solid Bronze Collection".
  • Available in a "Right Hand" or "Left Hand" model. Model shown in photo is the "Right Hand" model.
  • Drop Bar measures 7". Back Plates measure 2-3/4" by 4-1/2". Ring diameter is 3-1/2".
  • Fits gate thicknesses of 3/4" to 2.5". The spindle that connects the front and back piece is a 5/16" square steel rod.
  • Bronze is an old world material that does not deteriorate in coastal or other regions. The Bronze finish, however, is a "living" finish. Please read more about this by clicking on the link.
  • If you have double doors and need a "dummy" ring turn to go with this, order our SKU 850072 (click here).
  • The use of a gate stop with this product is strongly recommended to protect the drop bar. A gate that slams in a strong wind can damage a bronze drop bar. The installation of a gate stop will protect the drop bar. Gate stop is offered for purchase during checkout.

Finishes:

  • Natural Solid Bronze
Click here for Information & Pricing

Large Ring Turn, Solid Bronze

Large Ring Turn, Solid Bronze
  • Solid Bronze ring turn for use in coastal areas or anywhere a rustic old world design is desired. From our "Solid Bronze Collection".
  • Ring turn may be used as a "pull" or may be combined with a spring latch (our SKU 634014) and spindle (our SKU 634004) to create a gate latch.
  • To create a gate latch purchase 2 ring turns (one for the front and one for the back of the gate or door), one spindle and one spring latch per gate or door.
  • Ring turn back plate measures 4-1/2" tall and 2-3/4" wide. Diameter of ring is 4-3/4".
  • Spring latch fits into a 1" diameter hole drilled into the edge of the door. Spring latch backset (distance from the edge of the door to the center of the spindle hole) is 2-3/4".
  • Spring latch bolt protrudes a maximum of 7/16" (similiar to the spring latch on a typical front door). Spring latch includes a solid brass trim piece for the edge of the door and a solid brass strike plate, both pieces are oil rubbed bronze finish. Also included with spring latch are fasteners, paper installation template and a dust box. Spring latch contains some steel internal parts.
  • Spindle is 5" long by 5/16" square. Can be used on a maximum 3" thick door. For narrower doors it can easily be cut down with a hacksaw. Spindle is made from steel with a yellow zinc plating.
  • Mounting screws are included with the ring turn.
  • Bronze is an old world material that does not deteriorate in coastal or other regions. The Bronze finish, however, is a "living" finish. Please read more about this by clicking on the link.

Finishes:

  • Solid Natural Bronze
Click here for Information & Pricing

Ring Turn, Solid Bronze

Ring Turn, Solid Bronze
  • Solid Bronze ring turn for use in coastal areas or anywhere a rustic old world design is desired. From our "Solid Bronze Collection".
  • Ring turn may be used as a "pull" or may be combined with a spring latch (our SKU 634014) and spindle (our SKU 634004) to create a gate latch.
  • To create a gate latch purchase 2 ring turns (one for the front and one for the back of the gate or door), one spindle and one spring latch per gate or door.
  • Ring turn back plate measures 4-1/2" tall and 2-3/4" wide. Diameter of ring is 3-1/2".
  • Spring latch fits into a 1" diameter hole drilled into the edge of the door. Spring latch backset (distance from the edge of the door to the center of the spindle hole) is 2-3/4".
  • Spring latch bolt protrudes a maximum of 7/16" (similiar to the spring latch on a typical front door). Spring latch includes a solid brass trim piece for the edge of the door and a solid brass strike plate, both pieces are oil rubbed bronze finish. Also included with spring latch are fasteners, paper installation template and a dust box. Spring latch contains some steel internal parts.
  • Spindle is 5" long by 5/16" square. Can be used on a maximum 3" thick door. For narrower doors it can easily be cut down with a hacksaw. Spindle is made from steel with a yellow zinc plating.
  • Mounting screws are included with the ring turn.
  • Bronze is an old world material that does not deteriorate in coastal or other regions. The Bronze finish, however, is a "living" finish. Please read more about this by clicking on the link.

Finishes:

  • Solid Natural Bronze
Click here for Information & Pricing

Curved Plate Lever Turn, Solid Bronze

Curved Plate Lever Turn, Solid Bronze
  • Solid Bronze lever turn for use in coastal areas or anywhere a rustic old world design is desired. From our "Solid Bronze Collection".
  • Lever turn is reversible, fits left hand and right hand doors.
  • Lever turn back plate measures 9-3/4" tall and 2-3/4" wide. Lever projection is 3-1/4".
  • Spring latch fits into a 1" diameter hole drilled into the edge of the door. Spring latch backset (distance from the edge of the door to the center of the spindle hole) is 2-3/8".
  • Spring latch bolt protrudes a maximum of 7/16" (similiar to the spring latch on a typical front door). Spring latch includes a solid brass trim piece for the edge of the door and a solid brass strike plate, both pieces are oil rubbed bronze finish. Also included with spring latch are fasteners, paper installation template and a dust box. Spring latch contains some steel internal parts.
  • Spindle is 5" long by 5/16" square. Can be used on a maximum 1-3/4" thick door. Spindle is made from steel with a yellow zinc plating.
  • Spindle, spring latch and mounting screws are included with the lever turn.
  • Bronze is an old world material that does not deteriorate in coastal or other regions. The Bronze finish, however, is a "living" finish. Please read more about this by clicking on the link.
  • This item is sold by the "Set". A set is two lever turns (one for front of door and one for the back),one latch and strike,one spindle and all fasteners needed for installation.

Finishes:

  • Natural Bronze
Click here for Information & Pricing

Lever Bar Latch, Solid Bronze

Lever Bar Latch, Solid Bronze
  • Very high quality Lever Bar Latch for gates and doors. Made from solid bronze.
  • Latch operates from both sides of the gate.
  • Made from solid bronze and is made for use in coastal areas or anywhere a rustic old world design is desired. From our "Solid Bronze Collection".
  • Available in a "Right Hand" or "Left Hand" model. Model shown in photo is the "Left Hand" model.
  • Drop Bar measures 7". Back Plates measure 2-3/4" by 4-1/2". Lever is 6" with a 3-1/4" projection.
  • Fits gate thicknesses of 3/4" to 2.5". The spindle that connects the front and back piece is a 5/16" square steel rod.
  • If you are installing this on double gates and you need a single dummy to go with this order our SKU 850132. These are sold by the each so if you need a dummy for the front of the gate and one for the back order two each SKU 850132. This single dummy is offered for purchase during checkout.
  • Bronze is an old world material that does not deteriorate in coastal or other regions. The Bronze finish, however, is a "living" finish. Please read more about this by clicking on the link.
  • The use of a gate stop with this product is strongly recommended to protect the drop bar. A gate that slams in a strong wind can damage a bronze drop bar. The installation of a gate stop will protect the drop bar. Gate stop is offered for purchase during checkout.

Finishes:

  • Natural Solid Bronze
Click here for Information & Pricing

Square Handled Lever Latch, Solid Bronze

Square Handled Lever Latch, Solid Bronze
  • Solid bronze spring loaded lever latch for use in coastal areas or anywhere a rustic old world design is desired.
  • From our "Solid Bronze Collection".
  • This gate latch is available in either a "Right Hand" or "Left Hand" model. The photo shows the "Left Hand" model of the latch and it shows the side of the latch that installs on the "pull" side of the gate (the "pull"side of the gate is the sidethat you pull toward you when opening).Please carefully consider the handing of your gate when ordering.
  • Includes:
    • One spring lever with drop bar and strike as shown in photo (for the "pull"side of the gate)
    • A second spring lever (for the"push" side of the gate).
    • One strike, either a Surface Mounted Strike (as shown in the photo) or a Jamb Mounted Strike.
    • Black coated stainless steel wood screws.
    • Square spindle to connect the inside spring lever to the outside spring lever.
  • Approximate overall dimensions of spring lever with drop bar and surface mounted strike(as shown in photo) are 6-1/4" by 3-1/4".
  • Projection is approximately 2-3/8".
  • When ordering please specify the following information (in the "Comment Section" when you check out)
    • The thickness of your gate. This is necessary so we can provide the proper size connecting spindle. This latch will accomodate any thickness of gate.
    • The type of strike that you want, either a "Surface Mounted Strike" as shown in the photo or
    • a "Jamb Mounted Strike" (installs on the edge of the doorjamb or gate post).
Click here for Information & Pricing

Octagonal Handled Lever Latch, Solid Bronze

Octagonal Handled Lever Latch, Solid Bronze
  • Solid bronze spring loaded lever latch for use in coastal areas or anywhere a rustic old world design is desired.
  • From our "Solid Bronze Collection".
  • This gate latch is available in either a "Right Hand" or "Left Hand" model. The photo shows the "Left Hand" model of the latch and it shows the side of the latch that installs on the "pull" side of the gate (the "pull" side of the gate is the side that you pull toward you when opening). Please carefully consider the handing of your gate when ordering.
  • Includes:
    • One spring lever with drop bar and strike as shown in photo (for the "pull" side of the gate)
    • A second spring lever (for the "push" side of the gate).
    • One strike, either a Surface Mounted Strike (as shown in the photo) or a Jamb Mounted Strike.
    • Black coated stainless steel wood screws.
    • Square spindle to connect the inside spring lever to the outside spring lever.
  • Approximate overall dimensions of spring lever with drop bar and surface mounted strike(as shown in photo) are 6-1/2" by 3-1/4".
  • Projection is approximately 2-5/8".
  • When ordering please specify the following information (in the "Comment Section" when you check out)
    • The thickness of your gate. This is necessary so we can provide the proper size connecting spindle. This latch will accomodate any thickness of gate.
    • The type of strike that you want, either a "Surface Mounted Strike" as shown in the photo or
    • a "Jamb Mounted Strike" (installs on the edge of the door jamb or gate post).
Click here for Information & Pricing

Turn Lever on Plate, Single Dummy

Turn Lever on Plate, Single Dummy
  • Single dummy Turn Lever on Plate. Made from Solid Bronze.
  • Made from solid bronze and is made for use in coastal areas or anywhere a rustic old world design is desired. From our "Solid Bronze Collection".
  • This item is a "Single Dummy" handle for our "Lever Bar Latch, Solid Bronze" (SKU 850078 and 850076). You would normally order single dummys when you are installing our "Lever Bar Latch, Solid Bronze" on double gates.
  • This item is sold by the "Each". If you want a dummy lever on both the outside and inside of the gate you should order one "Left Hand" lever (SKU 850131) and one "Right Hand" lever (SKU 850132).
  • Back plate measures 2-3/4" by 4-1/2". Lever is 6" with a 3-1/4" projection.
  • The lever on this product is movable. To install as a dummy,install the small fixed spindle (included with purchase) under the lever handle.
  • Bronze is an old world material that does not deteriorate in coastal or other regions. The Bronze finish, however, is a "living" finish. Please read more about this by clicking on the link.
  • PLEASE NOTE: This product is "handed", available in a Left Hand and a Right Hand model. The image shown is a "Right Hand" model, SKU 850132.
Click here for Information & Pricing

8" Back-to-Back Thumb Latch, Solid Bronze

8
  • Solid bronze thumb latch for "Back-to-Back" gate or door installations. A "Back-to-Back" installation is one in which each thumb latch is installed exactly opposite each other, one on the inside of the gate and one on the outside of the gate.
  • Our solid bronze hardware is for use in coastal areas or anywhere a rustic old world design is desired. From our "Solid Bronze Collection".
  • This latch is made up of 3 components; an inside thumb latch, an outside thumb latch and a drop bar (latching mechanism). Each thumb latch measures 8-5/8" tall by approximately 1-7/8" wide at the widest point. The drop bar measures approximately 8" wide by 4" tall at the tallest point.
  • Sold by the Set. One Set will latch one door.
  • There are 3 SKU's available depending on your gate thickness. SKU number 850110 fits for gate thicknesses of 1.5" to 2". SKU number 850111 for gate thicknesses of 2" to 2.5". SKU number 850112 for gate thicknesses of 2.5" to 3".
  • Wood screws are included.
  • The use of a gate stop with this product is strongly recommended to protect the drop bar. A gate that slams in a strong wind can damage a bronze drop bar. The installation of a gate stop will protect the drop bar. Gate stop is offered for purchase during checkout.
  • Bronze is an old world material that does not deteriorate in coastal or other regions. The Bronze finish, however, is a "living" finish. Please read more about this by clicking on the link.

Finishes:

  • Solid Natural Bronze
Click here for Information & Pricing

Solid Bronze Thumb Latch

Solid Bronze Thumb Latch
  • Solid bronze thumb latch for use in coastal areas or anywhere a rustic old world design is desired. From our "Solid Bronze Collection".
  • This thumb latch is made up of two components; a thumb latch (available in 8" or 10" and a drop bar (available with or without a knob). The thumb latch installs on the outside of the gate and the drop bar installs on the inside of the gate.
  • The drop bar with knob (SKU 850060)measures 7.5" by 3.75".
  • The drop bar without knob (SKU 850064) measures 6.5" by 4".
  • For gate thicknesses up to 2-3/4".
  • If you have a gate thickness more than the above dimensions order our Extension Kit (SKU 850044). Fits gate thickness up to 4". PLEASE NOTE; The Extension Kit (SKU 850044) will ship to you already installed in the thumb latch.
  • Wood screws are included.
  • Bronze is an old world material that does not deteriorate in coastal or other regions. The Bronze finish, however, is a "living" finish. Please read more about this by clicking on the link.
  • The use of a gate stop with this product is strongly recommended to protect the drop bar. A gate that slams in a strong wind can damage a bronze drop bar. The installation of a gate stop will protect the drop bar. Gate stop is offered for purchase during checkout.

Finishes:

  • Solid Natural Bronze
Click here for Information & Pricing

Solid Bronze Handle

Solid Bronze Handle
  • Solid bronze non-working handle for gates and doors. From our "Solid Bronze Collection".
  • This handle matches our Solid Bronze Thumb Latch and is ideal for use on double doors or gates.
  • Wood screws are included.
  • Bronze is an old world material that does not deteriorate in coastal or other regions. The Bronze finish, however, is a "living" finish. Please read more about this by clicking on the link.

Finishes:

  • Solid Natural Bronze
Click here for Information & Pricing

Pull for Gates and Doors, Solid Bronze

Pull for Gates and Doors, Solid Bronze
  • Solid bronze pull for gates and doors for use in coastal areas or anywhere a rustic old world design is desired. From our "Solid Bronze Collection".
  • Available in two lengths; 12.5" and 17.5".
  • The 12.5" size has a screw hole center to center dimension of 11.5".
  • The 17.5" size has a screw hole center to center dimension of 16.5".
  • Attachment screws are included (Stainless steel hex head 5/16" diameter machine screws). Please specify in the comment section when you check out whether you would like your attachment screws 2" in length or 2-1/2" in length.
  • Bronze is an old world material that does not deteriorate in coastal or other regions. The Bronze finish, however, is a "living" finish. Please read more about this by clicking on the link.
  • PLEASE NOTE: We can special order these pulls so that you can mount one on each side of your door with no mounting hardware or screws visible (known as "back-to-back mounting"). Please call if you wish to order "back-to-back" mounting. We will need to know your door thickness. There is an additional charge of $30.00 for two pulls set up for "back-to-back mounting".

Finishes:

  • Solid Natural Bronze
Click here for Information & Pricing

Solid Bronze Gate Grill

Solid Bronze Gate Grill
  • Gate grille covers up a speakeasy opening on your gate or door.
  • Solid bronze gate and door grill for use in coastal areas or anywhere a rustic old world design is desired. From our "Solid Bronze Collection".
  • Grill measures 14-1/4" by 14-1/4" and is made from 1/2" square solid bronze.
  • Gate grille covers up a speakeasy opening on your gate or door.
  • Wood screws are included.
  • Bronze is an old world material that does not deteriorate in coastal or other regions. The Bronze finish, however, is a "living" finish. Please read more about this by clicking on the link.

Finishes:

  • Solid Natural Bronze
Click here for Information & Pricing

Cane Bolt, Solid Bronze 20"

Cane Bolt, Solid Bronze 20
  • Solid bronze cane bolt for use in coastal areas or anywhere a rustic old world design is desired. From our "Solid Bronze Collection".
  • Cane bolt measures 20" tall. Mounting plates measure 2" by 4".
  • Cane bolt features a large diameter 5/8" bolt.
  • Wood screws and a keeper for the bottom of the bolt are included.
  • Bronze is an old world material that does not deteriorate in coastal or other regions. The Bronze finish, however, is a "living" finish. Please read more about this by clicking on the link.

Finishes:

  • Solid Natural Bronze
Click here for Information & Pricing

Door Studs, Solid Bronze

Door Studs, Solid Bronze
  • Solid bronze door studs (also known as "Clavos" are a decorative item used to dress up doors or gates.
  • They are made from solid bronze and will age like the other bronze items shown on our website.
  • These door studs are available in two shapes; round and square. And they are available in two sizes; 1" and 2".
  • Door studs install by gently taping into a pre-drilled hole in the door or gate.
  • Bronze is an old world material that does not deteriorate in coastal or other regions. The Bronze finish, however, is a "living" finish. Please read more about this by clicking on the link.

Finishes:

  • Solid Natural Bronze
Click here for Information & Pricing

Exterior Offset Shutter Hinge, Solid Bronze

Exterior Offset Shutter Hinge, Solid Bronze
  • Solid Bronze exterior shutter hinges are for use in coastal areas or anywhere a rustic old world design is desired. From our "Solid Bronze Collection".
  • These shutter strap hinges are for "inset" shutters. Shutters are installed flush with the window frame when in the closed position (covering the window).
  • Available in two offset sizes: 1-1/4" and 2-1/4".
    • The 1-1/4" offset hinge (SKU 850340) gives a throw of 2-1/2".
    • The 2-1/4" offset hinge (SKU 850342) gives a throw of 4-1/2".
  • The offset of the hinge allows the shutter to lay flat against the house when in the open position. Click on the link below for more information about "Throw" and "Offset".
  • Shutter strap size for both hinges is 1-1/4" by 10".
  • Pintle plate measures 1-1/4" by 3-1/2" by 1/4". Pintle diameter is 3/8".
  • Shutter may be lifted off of pintles after installation.
  • Matching wood screws are included.
  • Sold by the each. Order two hinges for each shutter.

Finishes:

  • Natural Solid Bronze
Click here for Information & Pricing

Shutter Hinge, New York Style, 2-1/4" Offset, Solid Bronze

Shutter Hinge, New York Style, 2-1/4
  • Solid Bronze exterior shutter hinge matches other products from our "Solid Bronze Collection".
  • For exterior shutters which are hung flush with the casing (full inset).
  • Overall hinge dimensions are; 6" tall by 6-3/4" wide. Width is 1".
  • Pintle plate is 3-5/8" tall by 1-3/16" wide.
  • Available in two offsets; 1-1/4" Offset (for wood frame construction) and 2-1/4" Offset (for brick construction).
  • The 1-1/4" Offset Type has a throw dimension of 2-1/2". Click on link below for generic throw diagram
  • The 2-1/4" Offset Type has a throw dimension of 4-1/2". Click on link below for generic throw diagram.
  • Loose joint hinges permit easy hanging and easy removal of shutters.
  • Made from solid bronze material. Bronze is a "living finish". Please click on link below for more info on solid bronze hardware.
  • This product is sold by the pair. A pair is two hinges (one top hinge and one bottom hinge), enough to hang one shutter.
  • Matching wood screws are included.
Click here for Information & Pricing

Solid Bronze Shutter Dog

Solid Bronze Shutter Dog
  • Solid bronze shutter dog for use in coastal areas or anywhere a rustic old world design is desired. From our "Solid Bronze Collection".
  • For both working and non-working shutters.
  • These shutter dogs are handed (Right Hand or Left Hand). As you are standing outside the house looking at your pair of shutters, the right hand shutter dog goes on the shutter on your right and the left hand shutter dog goes on the shutter on your left. The shutter dog in the photo is a Right Hand model. If you are ordering two shutter dogs for a window that has a shutter on each side, order one left hand and one right hand.
  • The Shutter Dog measures 7" tall and 2-1/2" wide. Included is a 4.5" lag bolt. Please note; lag bolt is made from stainless steel.
  • These shutter dogs are sold by the each. Order one shutter dog per shutter.
  • Bronze is an old world material that does not deteriorate in coastal or other regions. The Bronze finish, however, is a "living" finish. Please read more about this by clicking on the link.

Finishes:

  • Solid Natural Bronze
Click here for Information & Pricing

Shutter Ring Pull, Solid Bronze

Shutter Ring Pull, Solid Bronze
  • Solid Bronze Ring Pull for shutters, cabinets, windows.
  • Solid Bronze material is great for use in coastal areas or anywhere a rustic old world design is desired. From our "Solid Bronze Collection".
  • Mounting plate measures 2-1/2" tall by 2" wide.
  • Bronze is an old world material that does not deteriorate in coastal or other regions. The Bronze finish, however, is a "living" finish. Please read more about this by clicking on the link.
  • Matching stainless steel wood screws are included.
Click here for Information & Pricing

Window Lever, Solid Bronze

Window Lever, Solid Bronze
  • Window lever or latch for casement windows.
  • Made from Solid Bronze material.
  • For use in coastal areas or anywhere a rustic old world design is desired. From our "Solid Bronze Collection".
  • Supplied with two strike plates for different installation methods. One is a mortise plate for mortising into the edge of the window frame and the other is a surface mounted plate for the surface of the window frame.
    • Dimensions:
      • Mortise plate is 3-3/16" tall by 13/16" wide.
      • Surface plate is 2-3/8" tall by 13/16" wide.
      • Mounting plate for lever is 2-3/8" tall by 13/16" wide.
      • Grip for lever is approximately 3-3/4" long. Projects 1-1/2" from surface.
  • Bronze is an old world material that does not deteriorate in coastal or other regions. The Bronze finish, however, is a "living" finish. Please read more about this by clicking on the link

Click here for Information & Pricing

Casement Window Stay, Solid Bronze

Casement Window Stay, Solid Bronze
  • Casement window stay made from Solid Bronze material.
  • Solid Bronze window stay matches other products from our "Solid Bronze Collection".
  • Casement stay is used to hold a window in various open positions. Keeps wind from opening or closing window.
  • Available in two sizes: 10 inches long and 12 inches long.
  • Sold by the set; a set includes one casement window stay, two latch plates and stainless wood screws coated to match the bronze finish.
  • Mounting plates measure approximately 5/8" by 2".
  • Made from solid bronze material. Bronze is a "living finish". Please click on link below for more info on solid bronze hardware
Click here for Information & Pricing

Round Cabinet Knob, Solid Bronze

Round Cabinet Knob, Solid Bronze
  • Round cabinet knob made from Solid Bronze material.
  • Solid Bronze product matches other products from our "Solid Bronze Collection".
  • Includes mounting screw (made from plated steel), back plate and cabinet knob.
  • Back plate diameter is 1-3/8 inch. Knob diameter is 1-3/16 inch.
  • Made from solid bronze material. Bronze is a "living finish". Please click on link below for more info on solid bronze hardware
Click here for Information & Pricing

Oval Cabinet Knob, Solid Bronze

Oval Cabinet Knob, Solid Bronze
  • Oval cabinet knob made from Solid Bronze material.
  • Solid Bronze product matches other products from our "Solid Bronze Collection".
  • Includes mounting screw (made from plated steel), back plate and cabinet knob.
  • Back plate diameter is 1-3/8 inch.Oval knob measures 1" by 1-3/8". Projection is 1-1/4".
  • Made from solid bronze material. Bronze is a "living finish". Please click on link below for more info on solid bronze hardware
Click here for Information & Pricing

5 Inch Cabinet Pull, Solid Bronze

5 Inch Cabinet Pull, Solid Bronze
  • Solid bronze cabinet pull for use in coastal areas or anywhere a rustic old world design is desired. From our "Solid Bronze Collection".
  • Pull measures 5-1/8" in length. Projection is 1-3/16".
  • Screwhole center-to-center distance is 4".
  • Round head screws (stainless steel, coated to match bronze) are included.
  • Bronze is an old world material that does not deteriorate in coastal or other regions. The Bronze finish, however, is a "living" finish. Please read more about this by clicking on the link.
Click here for Information & Pricing