40mm European Hinges

40mm European Hinges

Most European hinges fit into a 1-3/8" (35mm)cup drilled in the back of the door. These European hinges fit into a 40mm cup. Available in Full Overlay, Half Overlay and Inset Versions. They are typically used in thicker cabinet doors. 40mm is approximately 1-9/16".

40mm European Hinges, Straight Arm Type (Frameless Overlay)

40mm European Hinges, Straight Arm Type (Frameless Overlay)
  • A 40 millimeter (approx 1-9/16") cup European hinge for thick doors. Maximum door thickness is 1-1/2".
  • Opening angle is 94 degrees, hinge is self-closing, finish is nickel plated.
  • This hinge is made for overlay doors on a frameless cabinet (no face frame). Minimum side panel thickness is 16mm (5/8").
  • A wide variety of overlays is possible depending on the mounting plate and bore distance used.
    • See "Overlay Chart" at link below. The overlay range is 10mm to 34mm.
    • After installation, the overlay is slightly adjustable.
      • It can be decreased by 4.5 mm (almost 3/16")
      • It can be increased by 1.5 mm (1/16")
  • Hinges are 3-way adjustable after installation. Mounting plates are 2-way adjustable after installation.
  • Mounting plates and hinges connect by "snapping" together.
  • PLEASE NOTE: European hinges are made up of two parts; the hinge and a mounting plate. You would normally order 2 hinges and 2 mounting plates per door.
  • Uses #6 flat head wood screws. Not included but offered for purchase during checkout.
Click here for Information & Pricing

40mm European Hinges, Straight Arm Type (Face Frame Overlay)

40mm European Hinges, Straight Arm Type (Face Frame Overlay)
  • A 40 millimeter (approx 1-9/16") cup European hinge for thick doors. Maximum door thickness is 1-1/2".
  • Opening angle is 94 degrees, hinge is self-closing, finish is nickel plated.
  • This hinge is made for overlay doors on a "face frame" cabinet. Minimum side panel thickness is 16mm (5/8").
  • A wide variety of overlays is possible depending on the mounting plate and bore distance used.
    • See "Overlay Chart" at link below. The overlay range possible is 18mm to 33mm.
    • After installation, the overlay is slightly adjustable.
      • It can be decreased by 4.5 mm (almost 3/16")
      • It can be increased by 1.5 mm (1/16")
  • Hinges are 3-way adjustable after installation. Mounting plates can be vertically adjusted after installation. Mounting plates and hinges connect by "snapping" together.
  • PLEASE NOTE: European hinges are made up of two parts; the hinge and a mounting plate. You would normally order 2 hinges and 2 mounting plates per door.
  • Uses #6 flat head wood screws. Not included but offered for purchase during checkout.
Click here for Information & Pricing

40mm European Hinges, Half Cranked Type

40mm European Hinges, Half Cranked Type
  • A 40 millimeter (approx 1-9/16") cup European hinge for thick doors. Maximum door thickness is 1-1/2".
  • Opening angle is 94 degrees, hinge is self-closing, finish is nickel plated.
  • This hinge is made for "half overlay" doors (also known as "back-to_back" doors on a frameless cabinet (no face frame). Minimum side panel thickness is 16mm (5/8").
  • A wide variety of overlays is possible depending on the mounting plate and bore distance used.
    • See "Overlay Chart" at link below.
    • After installation, the overlay is slightly adjustable.
      • It can be decreased by 4.5 mm (almost 3/16")
      • It can be increased by 1.5 mm (1/16")
  • Hinges are 3-way adjustable after installation. Mounting plates are 2-way adjustable after installation. Mounting plates and hinges connect by "snapping" together.
  • PLEASE NOTE: European hinges are made up of two parts; the hinge and a mounting plate. You would normally order 2 hinges and 2 mounting plates per door.
  • Uses #6 flat head wood screws. Not included but offered for purchase during checkout.
Click here for Information & Pricing

40mm European Hinges, Full Cranked Type

40mm European Hinges, Full Cranked Type
  • A 40 millimeter (approx. 1-9/16") cup European hinge for thick doors. Maximum door thickness is 1-1/2".
  • Opening angle is 94 degrees, hinge is self-closing, finish is nickel plated steel.
  • This hinge is made for "inset" doors on a frameless cabinet (no face frame). Minimum side panel thickness is 16mm (5/8").
  • See "Reveal and Bore Distance Chart" at the link below so that you can choose the proper mounting plate.
  • After installation, the hinge is adjustable by minus 4.5mm (slightly less than 3/16") and by plus 1.5 mm (1/16"). This means that you can increase the reveal by about 3 /16" or you can decrease the reveal by 1/16".
  • Hinges are 3-way adjustable after installation. Mounting plates are 2-way adjustable after installation. Mounting plates and hinges connect by "snapping" together.
  • PLEASE NOTE: European hinges are made up of two parts; the hinge and a mounting plate. You would normally order 2 hinges and 2 mounting plates per door.
  • Uses #6 flat head wood screws. Not included but offered for purchase during checkout.
Click here for Information & Pricing