Amerock Pivot Hinges

Amerock Pivot Hinges

  • Amerock pivot hinges for cabinets.
  • In this section you will find the following Amerock hinges;
    • Amerock pivot hinges for 3/8" partial inset doors.
    • Amerock pivot hinges for overlay doors.

Variable Overlay Pivot Hinge

Variable Overlay Pivot Hinge
  • Variable overlay hinge for cabinet doors.
  • Made for 3/4" thick doors.
  • Hinge may be surface mounted or may be mortised into the surface (see install info link below).
  • This hinge is an exact duplicate of BP1242-2G Amerock hinge that was recently discontinued by Amerock.
  • The Amerock BP1242-2G was made in a zinc finish. Our hinge is a satin nickel finish.
  • The hinge is sold by the set. A set includes a top hinge and a bottom hinge as shown in the photo.
  • The horizontal leaf of this hinge attaches to the back of the door. The vertical leaf attaches to the front or face of the cabinet.
  • Wood screws are included.
  • PLEASE NOTE: This hinge is not made by Amerock. It is a replica of a hinge that Amerock no longer manufactures.

PLEASE NOTE: this hinge is currently in limited supply. We reserve the right to limit purchase quantities.

Click here for Information & Pricing

Amerock 1242 Pivot Hinge

Amerock 1242 Pivot Hinge
  • Pivot hinge for overlay doors.
  • Overlay is variable, no maximum overlay, minimum overlay is 1".
  • Hinge needs a minimum of 1" of width on the cabinet frame to install.
  • Made for 3/4" thick doors.
  • Made from steel base material and zinc chromate plated.
  • Each hinge uses up to 6 each #6 flat head wood screws (each pair of hinges uses up to 12 screws).
  • Screws are not included but are offered for purchase. Order our SKU 652360.
  • Elongated screw holes offer ease of adjustment during installation.
  • This hinge is sold by the pair. A pair is two hinges which means a top hinge and a bottom hinge.

Please note that this hinge has been discontinued by Amerock. Our SKU732022 is a substitute for this hinge. You can click on the link below to go directly to this hinge.

Click here for Information & Pricing

Amerock Marathon Face Frame Pivot Hinge

Amerock Marathon Face Frame Pivot Hinge
  • For cabinets with a face frame
  • Steel base material with plastic spring mechanism
  • Matching wood screws are included
  • SKU numbers 399969, 399907 are for 1/4" overlay doors
  • SKU number 399961 is for a 3/8" partial inset door
  • These hinges are not handed
  • If you are trying to match an existing hinge look for the style number stamped on your hinge.
    • Style #4 (our SKU 399961)is for a 3/8" partial inset door (3/4" door thickness).
    • Style #5 (our SKU 399969)is for a 5/8" to 3/4" thick door with a 1/4" overlay.
    • Style #3 (our SKU 399907) is for a 1/2" thick door with a 1/4" overlay.

Please note: The #4 and #5 Marathon hinge have been discontinued by the manufacturer and are no longer available.

    Finishes:

  • White
Click here for Information & Pricing

Amerock 1247 Pivot Hinges

Amerock 1247 Pivot Hinges
  • PLEASE NOTE:
  • Pivot hinge is made for 3/8" partial inset doors (also known as 3/8" inset doors with a 3/8" lip)
  • Fits doors that are 3/4" thick.
  • Sold as a pair which includes a left hand hinge right hand hinge.
    • The obsolete Amerock hinges were marked to show which hand the hinge was
    • The right hand hinge was marked "R", the left hand hinge was marked "L"..
    • If the hinges are used on horizontally swinging doors the left hand hinge is used as the top pivot and the right hand hinge is used as the bottom pivot..
    • The photo to the left shows the "Left Hand" hinge. The bottom leaf attaches to the edge of the face frame. The top leaf attaches to the back of the door.
  • The pivot point of the hinge installs in a 1/4" slot cut in the lip of the door from the backside of the door.
  • If you are replacing old hinges your hinge should have the number "1247" stamped on it (usually not visible when the hinge is installed).
  • Matching wood screws are included (8 screws per pair). Made from steel base material.

Finishes:

  • Burnished Brass
  • Zinc Chromate
  • Click here for Information & Pricing

    1247 Pivot Hinge for 3/8" Partial Inset Doors

    1247 Pivot Hinge for 3/8
    • Pivot hinge is made for face frame cabinets with a 3/8" partial inset door.
    • A 3/8" partial inset door is a door which partially insets into the cabinet opening and partially overlays the cabinet opening.
    • The door has a "rabbetted edge". The inset dimension measures 3/8" and the lip dimension measures 3/8".
    • This hinge is made for doors that are 3/4" thick.
    • The pivot point installs in a slot (approximately 1/4") cut into the door lip. When the door is closed, this slot is only visible from the side, and not from the front of the cabinet.
    • This hinge is a replica of a hinge that was once made by Amerock. It was Amerock's 1247 hinge and was available in two finishes: Burnished Brass and Zinc Chromate.
    • The hinge is sold by the pair. A pair includes a "Left Hand" hinge and a "Right Hand" hinge.
    • Can be used on doors that swing horizontally or doors that swing vertically.
    • Matching wood screws are included.
    • Installation:
      • The photo shows a Right hand and a Left hand hinge (one pair of hinges)
      • The bottom hinge leaf normally attaches to the edge of the face frame.
      • The top leaf normally attaches to the back of the door.

    Finishes:

    • Satin Nickel
    • Antique Brass
    Click here for Information & Pricing

    Amerock 1238 Pivot Hinge

    Amerock 1238 Pivot Hinge
    • Overlay pivot hinge by Amerock
    • Made for frameless cabinets with 3/4" side panel thickness
    • This hinge has been discontinued by Amerock.
    • We have a duplicate hinge, our SKU 286432, available in nickel or bronze finishes
    • Click on link below to open our page for SKU 286432.
    Click here for Information & Pricing

    Marathon Face Frame Pivot Hinge

    Marathon Face Frame Pivot Hinge
        • For cabinets with a face frame
        • Steel base material with plastic spring mechanism
        • Matching wood screws are included
        • SKU numbers 399950, 399960 and 399965 are for overlay doors
        • These hinges are not handed
        • If you are trying to match an existing hinge look for the style number stamped on your hinge.

        PLEASE NOTE: The following versions of this hinge have been discontinued by the manufacture and are no longer available:

        • Style #4 (our SKU 399955) was for a 3/8" partial inset door (3/4" door thickness).
        • Style #5 (our SKU 399960) was made for a 5/8" to 3/4" thick door with a 1/4" overlay.
        • Style #3 (our SKU 399950)was for a 1/2" thick door with a 1/4" overlay.

        This hinge is available in a white finish. Click HERE, to go to the hinge in a white finish.

        Finishes:

        • Burnished Brass
    Click here for Information & Pricing