• A very high security hasplock for commercial and residential use. Provides excellent security for gates, doors, cabinets, storage boxes, tool boxes, sheds, boats, storefronts and factory compounds. Hasplock is resistant to tampering and hacksawing.
• Made from type 316 grade stainless steel and finished with a beautiful high polish.
• This model is made for flat surfaces (flush installation). Click on link below to view installed product.
• When not in locked position, hasp pivots downward so as not to obstruct a closing gate or door.
• Hasplock measures 4.5" long by 3-3/16" tall. Projection is 2-1/16".
• Locking mechanism is a deadlock design. Hasp cannot be locked without the key.
• The 6-pin locking cylinder can be keyed alike or master keyed by your locksmith. It can be replaced with high security cylinders such as Assa-Abloy, Kabo, Medico, Mul-T-Lock or Schlage Primu and many others.

Finishes:

• Polished Stainless Steel

• Stainless steel bolt is very high quality and secures gates and garage doors.
• Rust resistant stainless steel is recommended for vinyl, redwood, cedar and ACQ (treated) lumber.
• Available in three sizes; Large measures 5-1/4" by 2-3/4". Small measures 4" by 2-1/4". Mini measures 2-3/4" by 1-1/2".
• Two different strike plates are included. The strike can either be surface mounted or edge mounted.
• Includes stainless steel screws.
• Bolt can be locked in either the open position or the closed position with a padlock.
• The bolt on the "small" size is .350" in diameter. The bolt on the "large" size is .475" in diameter. The bolt on the "mini" size is .250".

Finishes:

• Stainless Steel

• Stainless steel slide bolt secures gates and garage doors.
• Rust resistant stainless steel is recommended for vinyl, redwood, cedar and ACQ (treated) lumber.
• Measures approximately 6.5" by 2.25"
• Strike plate can be mounted either as a surface mount or edge mount plate.
• Includes stainless steel screws and 1/4" by 2.5" stainless steel carriage bolts.
• Bolt can be locked in either the open position or the closed position with a padlock.
• Diameter of slide bolt is just under 3/8"
• Made from solid stainless steel (Type 304)

Finishes:

• Stainless Steel

• Gate latch for use around a pool, in a marine or corrosive environment or anywhere the look of satin stainless steel is desired.
• Safe for use on redwood, cedar, ACQ lumber (treated lumber) and vinyl.
• Baseplate measures 1-5/8" by 1-1/2".
• Latch bar measures 4-1/4".
• Installs on hinged side of gate. For single acting gates (gates that open in only one direction).
• Made from solid stainless steel (Type 304)
• Stainless steel screws are included.

Finishes:

• Satin Stainless Steel

• Stainless steel barrel bolt has a satin stainless steel finish.
• Width is 1-1/16". Available in a 5" and a 7.5" length. Projection is 5/8".
• Made from Type 304 stainless steel. Slide bolt and knob are made from brass and nickel plated.
• Comes with two keepers. One keeper is for surface mounting the other keeper is for edge mounting.
• Stainless steel flat head screws are included.

Finishes:

• Satin Stainless Steel

• Barrel bolt is made of heavy duty solid stainless steel.
• Made from solid stainless steel (Type 304)
• Bolt measures 5.5" long by approximately 3/4" in diameter.
• The bolt housing and surface strike measure 6-3/8" by 2-3/4" (as shown in photo).
• Rust resistant stainless steel is recommended for vinyl, redwood, cedar and ACQ (treated) lumber.
• The bolt can be locked with a padlock in the locked position.
• A surface mounted strike plate and an edge mounted strike plate are included. Stainless steel screws are included.

Finishes:

• Satin Stainless Steel

• Stainless steel hasp accepts padlock for locking gates, boxes, chests, doors, cabinets, etc.
• Made from Type 304 stainless steel.
• Available in 4 sizes; Large, Medium, Small and Extra Small.
• Stainless steel screws are included.
• Padlock eye rotates 360 degrees. When a padlock is attached the padlock eye is held in the vertical position (via gravity) to help secure the hasp.

Finishes:

• Polished Stainless Steel

• Deadbolts for gates with exterior trim pieces made from stainless steel.
• Available in Single Cylinder or Double Cylinder.
• Double Cylinder model is keyed on both sides.
• Single Cylinder model has a keyed side for the outside of the gate and a throw knob for the inside of the gate.
• For gate thicknesses of 1-3/8" to 1-3/4".
• Installs in a 2-1/8" round hole.
• Both locks use the common Schlage keyway.
• All screws and hardware necessary for installation are included.
• PLEASE NOTE; the inside workings of these locks are not made from stainless steel. We do not know of any dead bolt system that is made from 100% stainless steel, inside and out. We offer these items for gates because they offer much better corrosion resistance than other dead bolt where the outside trim pieces are made from plated steel.

Finishes:

• Satin Stainless Steel