• Heavy duty weld on hinges made with dependable roller bearing design.
• Roller bearings are made using a hardened steel inner race and a hardened steel roller cage bearing held in place with a Grade 5, zinc plated bolt.
• Hinge is fitted with a grease fitting for applying periodic lubrication.
• Hinge features a very large weld surface for maximum weight bearing.
• Available in two weight ratings; 1000 lbs per pair of hinges and 3000 lbs per pair of hinges.
• Click on links below for dimension diagrams of each hinge.
• Hinges are prime coated, ready for painting after installation.
• Hinges are sold by the each. Order a minimum of two hinges per door or gate.

• Pivot type welding hinge with roller bearings.
• Available in a 3" or a 4" size.
• The 3" size has a sealed roller bearing that measures 1-3/8" outside diameter by .622" inside diameter by .43" thick. Uses a 1/2" x 4" pivot bolt. Post side welding plate measures 1.5" x 3.5". Gate side welding plate measures 1.5" x 2.75". The spacing between the gate and post is 2.71".
• The 4" size has a sealed roller bearing that measures 1.849" outside diameter by .786" inside diameter by .55" thick. Uses a 5/8" x 5" pivot bolt. Post side welding plate measures 2" x 4.25". Gate side welding plate measures 2" x 3.25". The spacing between the gate and post is 4.25".
• Both hinges feature a 220 degree swing range. Both hinges use a nylon locking nut on the bottom of the pivot bolt.
• Made from steel base material.
• These hinges are sold by the pair which means two hinges. A pair is normally what you need to hang one gate.
• Weight ratings are based on using a pair of hinges.
• Hinges are made in the U.S.A.

Finishes:

• Painted Black

• 3.5" tall Gorilla Weld-on Hinge.
• For trash enclosures, gates, high security applications, prison doors and gates.
• Both sides are meant to mount to flat surfaces.
• Hinge is built to reduce the space between the jamb or post and the gate.
• Weight rated to 1000 lbs per pair of hinges.
• Made from steel and prime coated.
• Allows for 180 degree swing.
• Hardened roller bearing design
• High security welded pin design
• Includes zerk fitting for lubrication.
• These hinges are sold by the "each". You would normally order 2 hinges for each door or gate.

• Hinge will allow gate to swing open up a hill.
• Available in a Standard Duty Model and a Heavy Duty Model
• Standard Duty Model is rated for a 600 lb. gate.
• Standard Duty measurements: Bottom hinge is 12" long, Top Hinge is 6" long. Bottom and Top Hinges are 3" tall by 3" wide and made from 3/8" thick steel.
• Heavy Duty Model is rated for a 2000 lb. gate.
• Heavy Duty measurements; Bottom hinge is 12" long, Top Hinge is 6" long. Bottom and Top Hinges are 4-3/8" tall by 3-1/2" wide and made from 1/2" thick steel.
• Hinge is a "Weld on" type hinge.
• Made from steel and prime coated.
• A grease fitting allows lubrication of pivot.
• Installation instructions are included.
• Click on link below to see installation instructions.
• Sold by the pair. A pair of hinges will hang one gate.
• A pair is made up of a top hinge (the shorter of the two hinges) and a bottom hinge.

• Weld-on barrel hinge is a lift off pivot hinge.
• Features a round barrel body.
• Made from steel base material and plated with a bright zinc plating.
• Hinge pin pivots on a ball bearing.
• Features a "zerc" type grease fitting to keep the bearing lubricated.
• The hinge pin is fixed in one of the barrels. In the photo to the left the barrel with the fixed hinge pin is the barrel on top.
• The "Hinge Gap" is the distance between the post and the gate after the hinge is installed.
• Each hinge has 2 weldable plates. Each plate measures as follows; SKU 782500 measures 7/8" x 2" x 5/16" and SKU 782510 measures 1-3/4" x 3" x 3/16".
• SKU #782500 use for gates up to 6-8 feet wide
• SKU #782510 use for gates up to 12-15 feet wide

Finishes:

• Weld-on barrel hinge is a lift off pivot hinge.
• Features a round barrel body.
• Made from steel base material.
• Hinge pin is made from stainless steel.
• Hinge pin pivots on a ball bearing.
• Features a "zerc" type grease fitting.
• The hinge pin is fixed in one of the barrels. In the photo to the left the barrel with the fixed hinge pin is the barrel on top.
• The "Hinge Gap" is the distance between the post and the gate after the hinge is installed.
• Each hinge has 2 weldable plates. Each plate measures as follows; SKU 782000 measures 1" x 2" x 3/8" and SKU 782002 measures 1-1/2" x 3" x 3/8".
• SKU #782000 use for gates up to 8-10 feet wide
• SKU #782002 use for gates up to 15-17 feet wide

• This 2-piece weld-on hinge is extremely popular because of its high weight load capacity as well as it professional appearance.
• Ideal for gates, machinery doors, barbeque pits, electrical boxes, and trailers.
• It can be welded on as a lift-off hinge or it can be permanently mounted.
• Made from mild steel (1015) with a case hardened fixed steel pin and a brass washer.
• Weight rating shown is for a pair of hinges. A pair of hinges is two hinges.
• The "S-dimension" is the diameter plus the welding area.

• This 2-piece weld-on hinge is extremely popular because of its high weight load capacity as well as it professional appearance.
• Ideal for gates, machinery doors, barbeque pits, electrical boxes, and trailers.
• It can be welded on as a lift-off hinge or it can be permanently mounted.
• Made from stainless steel (Type 304) with a case hardened fixed stainless steel pin and a stainless steel washer.
• Weight rating shown is for a pair of hinges. A pair of hinges is two hinges.
• The "S-dimension" is the diameter plus the welding area.

• Super heavy duty weld-on pivot hinge for very heavy gates.
• Hinge measures 7" tall by 2.5" in diameter. Each weld-on plate measures 2.75" tall by 2" wide.
• The hinge pin is made from stainless steel, is 1.25" in diameter and rides on a 1" diameter ball bearing.
• Barrels are made from cold rolled carbon steel.
• Maximum gate weight is 3000 lbs per pair of hinges.
• Includes a "zerk" type fitting so that the hinge may be lubricated with a grease gun.
• Hinges are made in the U.S.A.
• These hinges are sold by the pair which means two hinges. A pair is normally what you need to hang one gate. A pair of these hinges weighs about 22 lbs.

Finishes:

• Painted Black

• heavy duty weld-on hinges
• fast spun pin
• for heavy duty applications
• not swaged for mortising
• no holes
• hinge widths are approximately 1/8" less than nominal sizes shown
• all sizes have five knuckles

• Stainless Steel (Type 304) weld-on hinges.
• Lift-off type hinges, hinge and door may be lifted off after installation.
• Finish is a type 2B mill finish (an industrial finish).
• The manufacturer of this hinge does not provide any weight ratings but they will be comparable to other hinges of the same height, open width and thickness.
• Available in Left Hand and Right Hand models and in 4 different sizes.
• Before ordering please view the Left Hand and Right Hand comparison diagram by clicking on the link below.
• These hinges are sold by the "Each". Order a minimum of 2 each per each door you are hanging.

• Stainless Steel (Type 304) weld-on hinges.
• Tight pin (spun-on).
• Finish is a type 2B mill finish (an industrial finish).
• The manufacturer of this hinge does not provide any weight ratings but they will be comparable to other hinges of the same height, open width and thickness.
• This welding hinge is available in 8 different sizes.
• PLEASE NOTE: the different size hinges differ in that they have a different number of hinge knuckles depending on the size. The smaller hinges have 5 knuckles (as shown in the photo). The larger hinges may have more.

• Stainless steel flag hinge for welding.
• Made from type 304 stainless steel.
• Hinge is 6" tall by 2.5" wide. Click on link below for more dimensions.
• Hinge pin is fixed in bottom leaf. Top leaf will "lift off" bottom leaf.
• Top leaf rides on a ball bearing fixed to the top of the hinge pin.
• A pair of these hinges has a weight rating of 198 lbs.
• These hinges are available in either a Left Hand or Right Hand model as shown in photo.
• These hinges are sold by the "each". You would normally order 2 hinges per door you are hinging.

Finishes:

• Satin Stainless Steel

• Stainless steel flag hinge for welding.
• Made from type 304 stainless steel.
• Hinge is 4" tall by 2.5" wide. Click on link below for more dimensions.
• Hinge pin is fixed in bottom leaf. Top leaf will "lift off" bottom leaf.
• Top leaf rides on a ball bearing fixed to the top of the hinge pin.
• A pair of these hinges has a weight rating of 88 lbs.
• These hinges are available in either a Left Hand or Right Hand model as shown in photo.
• These hinges are sold by the "each". You would normally order 2 hinges per door you are hinging.

Finishes:

• Satin Stainless Steel

• Heavy duty blank weld-on hinges.
• Hinge pin is removable.
• Non-swagged heavy hinge is designed for surface application by welding on metal.
• Made from cold rolled steel, not plated.
• All sizes have 5 knuckles.
• Weight rating applies to the use of 1, 2 or 3 hinges per hinged device. For example if the weight rating for one hinge is 40 lbs then the weight rating for 3 hinges is 120lbs. The weight ratings are do not apply to the use of more than 3 hinges.

Finishes:

• Natural

• Heavy duty blank weld-on hinges.
• Fast-spun pin, non-removeable.
• Non-swagged heavy hinge is designed for surface application by welding on metal.
• Made from cold rolled steel, not plated.
• All sizes have 5 knuckles.
• Weight rating applies to the use of 1, 2 or 3 hinges per hinged device. For example if the weight rating for one hinge is 40 lbs then the weight rating for 3 hinges is 120lbs. The weight ratings are do not apply to the use of more than 3 hinges.

Finishes:

• Natural

• Aluminum Weld-On Hinges.
• Tight pin (spun-on).
• Mill finish (an industrial finish).
• The manufacturer of this hinge does not provide any weight ratings but they will be comparable to other aluminum hinges of the same height, open width and thickness.
• This welding hinge is available in 5 different sizes.
• PLEASE NOTE; the different size hinges differ in that they have a different number of hinge knuckles depending on the size. The smaller hinges have 5 knuckles (as shown in the photo). Larger hinges may have more.

• This hinge has a reverse action spring which means that the spring action works to open the door.
• Non-template hinge, for wood doors. Hinges have screwholes but are also weldable for metal gates.
• Pivot points do not align with standard full mortise hinges. These hinges cannot be mixed with other types of hinges on the same door.
• Steel base material.
• Wood screws are included on the 3" size.
• Machine screws are included on the 6" size.
• The "Size" dimension is the height of the plate that mounts on the door and jamb.
• The 3" hinge maximum door weight is 45lbs using 2 hinges and 65lbs using 3 hinges.
• The 6" hinge maximum door weight is 125lbs using 2 hinges and 155lbs using 3 hinges.

Finishes:

• 652(US26D) Satin Chrome
• 601(US1B) Bright Black Japanned

• Non-template hinge, for wood doors. Hinges have screwholes but are also weldable for metal gates.
• Pivot points do not align with standard full mortise hinges. These hinges cannot be mixed with other types of hinges on the same door.
• Large diameter barrel matches older style single acting pivot hinges.
• Steel base material.
• The 3" hinge comes with wood screws.
• The 6" and 7" size come with machine screws.
• The "Size" dimension is the height of the plate that mounts on the door and jamb.
• The 3" hinge maximum door weight is 45lbs using 2 hinges and 65lbs using 3 hinges.
• The 6" hinge maximum door weight is 125lbs using 2 hinges and 155lbs using 3 hinges.
• The 7" hinge maximum door weight is 130lbs using 2 hinges and 175lbs using 3 hinges.

Finishes:

• 601 (US1B) bright black japanned
• 600 (USP) primed for painting.