Heavy Duty Strap Hinges

Heavy Duty Strap Hinges

Heavy duty strap hinges for large gates and doors. Some of these hinges can hold a gate that weighs several thousand pounds. There are over 50 heavy duty strap hinges in this section, all in stock and ready to ship out the next working day.

Heavy Duty Strap Hinges

Heavy Duty Strap Hinges
  • Heavy duty strap hinge.
  • Made from steel base material.
  • Zinc plated for corrosion resistance.
  • Special bearings increase life expectancy.
  • Uses flat head screws (not included). Screw size and quantities needed per hinge are listed below.
  • Flat head screws are offered for purchase during checkout.
  • PLEASE NOTE: The "Size" refers to the length of one hinge leaf. The "Size Open" dimension is the tip-to-tip measurement when the hinge is in the open position as shown in the photo.
Click here for Information & Pricing

Adjustable Curved Rail Strap Hinge

Adjustable Curved Rail Strap Hinge
  • Strap angle is adjustable to fit gates and doors with curved edges.
  • Hinge has a true galvanized finish (not zinc chromate plated), suitable for use around a sea coast.
  • Hinge strap is approximately 2-1/4" wide by 3/16" thick.
  • Vertical wing measures approximately 8" tall by 2-1/2" wide.
  • Angle of strap may be set at any angle from horizontal to 90 degrees up or down.
  • Made from steel base material.
  • Wood screws are provided for the vertical wing and 9/16" x 4" carriage bolts are provided for the strap.

Finishes:

  • Galvanized
Click here for Information & Pricing

Heavy Duty British Style Strap Hinges

Heavy Duty British Style Strap Hinges
  • Heavy duty strap hinge with Traditional British Hardware styling.
  • Strap is approximately 3/16" thick and 2" wide. Hinge pin is 5/8" in diameter.
  • Hardware as it is installed on post side of hinge measures approximately 6.5" tall by 2-1/4" wide.
  • Available in two finishes:
    • Black finish is amatte black coating.
    • Galvanized finish is a true heavy galvanizing suitable for outdoor use near a seacoast.
  • Matching wood screws are included.
    • One galvanized through bolt is included per hinge.
    • Through bolt is mounted in square hole.

Finishes:

  • Matte Black
  • Galvanized
Click here for Information & Pricing

Extra Heavy Duty British Style Strap Hinges

Extra Heavy Duty British Style Strap Hinges
  • These are the same hinges as our "Heavy Duty British Style Strap Hinges" except they are heavier and longer.
  • Extra Heavy duty strap hinge with Traditional British Hardware styling.
  • Strap is approximately 7/32" thick and 2-3/4" wide.
  • Hinge pin is 7/8" in diameter.
  • Hardware as it is installed on post side of hinge measures approximately 9.5" tall by 3" wide.
  • Black finish is amatte blackcoating.
  • Matching wood screws are included. One through bolt is included per hinge. Through bolt is mounted in square hole.

Finishes:

  • Matte Black Coating
Click here for Information & Pricing

Extra Heavy Duty Strap Hinge

Extra Heavy Duty Strap Hinge
  • These extra heavy duty ball bearing strap hinges can hold up to a 3800 lb. gate or door. Hinge choice is based on gate width and weight. See chart at link below to assist in hinge choice and number of hinges to use.
  • These are the best quality and heaviest weight strap hinges that we know of.
  • Offset pintle can be set back on face of jamb or wall to allow swing clear application.
  • Strap and pintle painted off-white. User can repaint with a different color if desired.
  • Pintle pin & bearings are zinc plated for rust resistance.
  • These hinges are made in USA.
  • Pintle uses 1/2" lag screw, strap uses 3/8" lag screw (Lag screws are not included with hinge).
  • Click on the link below for a table that gives the weight ratings for these hinges.

Finishes:

  • Painted off-white
Click here for Information & Pricing

Heavy Duty Lift-off Strap Hinges

Heavy Duty Lift-off Strap Hinges
  • Heavy duty strap hinge, door or gate can be lifted off after installation.
  • Available in two finishes;matte black or heavy galvanized (true galvanizing not zinc plated). Galvanized models are suitable for sea coast use.
  • Traditional British Hardware styling.
  • Made from 3/16" thick steel.
  • Vertical mounting plate sizes;
    • For SKU 215108, it measures 1-7/16" x 5-1/4".
    • For SKU 215130 and 215110, it measures 1.5" x 5-3/8".
    • For SKU 215132 and 215112, it measures 2" x 6.5".
    • For SKU 215134 and 215114, it measures 2-3/16" by 6.5".
    • For SKU 215136,it measures8" by 2-3/16".
  • Matching wood screws are included.
  • One galvanized through bolt is included per hinge(carriage bolt; 3/8" x 4"). Through bolt is mounted in square hole.

Finishes:

  • Matte Black
  • Galvanized
Click here for Information & Pricing

9" Cast Aluminum Strap Hinge

9
  • Strap side of hinge measures 2-1/2" wide by 9" long by 5/8" thick cast aluminum
  • Plate side of hinge measures 4-5/8" high by 2-3/4" wide by 3/8" thick
  • Hinge swings on bronze bearings
  • Each hinges uses 8 each #14 flat head screws (not included)
  • For doors where the frame and door are flush with each other
  • The hinges are rated at 200 lbs for a pair of hinges on a door up to 36" wide

Finishes:

  • Polished aluminum
  • Flat Black
Click here for Information & Pricing

12 Inch, 18 Inch and 24 Inch Strap Hinge

12 Inch, 18 Inch and 24 Inch Strap Hinge
  • Strap side of hinge measures 3" wide and 5/32" thick and is made of plated steel
  • Plate side of hinge measures 6-1/8" by 2-1/2" by 1/2" thick and is made of cast aluminum
  • Hinge swings on bronze bearings
  • For doors where the frame and the door are flush
  • Hinge requires 3/8"bolts (not included)
  • The 12", 18" and 24" dimensions are measured from the end of the strap to the pivot point of the strap
  • Weight Ratings are for two hinges per door

    SKU 902002 and 902010 are rated at 250lbs for up to a 36" door and 200lbs for a 36" to 40" door

    SKU 902004 and 902012 are rated at 300lbs for a 36" to 40" door and 250lbs for a 42" to 46" door

    SKU 902006 and 902014 are rated at 300lbs for up to a 48" door

Finishes:

  • Chrome plated, highly polished
  • Black Coated
Click here for Information & Pricing

Strap Hinges, Heart Style, Heavy Duty

Strap Hinges, Heart Style, Heavy Duty
  • Strap hinges are available in two finishes. The 4 smaller sizes are a "Rough Black Iron" finish. The 2 larger sizes are a "Smooth Black Iron" finish.
  • The hinge pin is removable so that the pad (smaller leaf) may be reversed. This allows the hinge to be installed as either a full-surface hinge or a half-surface hinge.
  • The weight rating on the 9" and 13" hinge applies to a door with a maximum door thickness of 1-3/8" and a maximum door width of 32" using 3 hinges per door.
  • The weight rating on the 17" and 20.5" hinge applies to a door with a maximum door thickness of 1-3/4" and a maximum door width of 36" using 3 hinges per door
  • The 30" and 36" hinges are extra heavy duty hinges and are rated at 600# per pair of hinges.
  • These hinges match our "Heart" style gate latches found in the Gate Latch and Gate Lock section of the website. Two "Heart" style latches are offered for purchase during checkout.
  • Complete with screws.
  • Made from steel base material.

Finishes:

  • Black Iron
Click here for Information & Pricing

Strap Hinge System, Solid Bronze

Strap Hinge System, Solid Bronze
  • This very high quality solid bronze strap hinge is made for use in coastal areas or anywhere a rustic old world design is desired. From our "Solid Bronze Collection".
  • This product is sold in components. The components consist of 2 items; a "Strap" which attaches to the gate surface and a pintle which attaches to the post. The pintle is available as either a "Plate Pintle" a "Screw-in Pintle" or a "Jam Pintle".
  • The "Plate Pintle" measures 2" wide by 6-1/4" tall. The plate material is about 1/4" thick. The pintle portion is 11/16" in diameter by 2" tall.
  • The "Screw-In Pintle" is available in two sizes, Small and Large. The small size measures 5" horizontally and 3-3/8" vertically. The pintle portion is 11/16" in diameter by 2" tall. The screw thread portion is 3-1/4" by 11/16". The large size measures 7.5" horizontally and 3-7/8" vertically. The pintle portion is 11/16" in diameter by 2" tall. The screw thread portion is 6" by 13/16".
  • The "Jam Pintle" is meant to be installed in the jamb or edge of the door frame or gate post and can be installed in a mortise (cutout). The mounting plate portion of the "Jam Pintle" measures 4-3/4" wide by 2-7/16" tall by 9/32" thick. The pintle is 2" tall by 11/16" in diameter. It is available in a Right Hand Model and a Left Hand Model. The image in the photo shows a Right Hand Model. Here is how the handing works: Go to the side of the gate or door where the hinges are visible (the hinged side of the door), stand with your back against the gate or door. If you want the hinges on your right then you should order the Right Hand Model. If you want your hinges on your left then you should order the Left Hand Model.
  • Lag screws (1-1/2" long)are included for the "Plate Pintle", flat head wood screws are included for the "Jam Pintle". Screws are made from stainless steel and coated black.
  • Two hinges will support a 150 lb. gate or door. Three hinges will support a 250 lb. gate or door.
  • Bronze is an old world material that does not deteriorate in coastal or other regions. The Bronze finish, however, is a "living" finish. Please read more about this by clicking on the link.

Finishes:

  • Natural Solid Bronze
Click here for Information & Pricing

Lift Off Strap Hinge, Stainless Steel, Heavy Duty

Lift Off Strap Hinge, Stainless Steel, Heavy Duty
  • Stainless steel strap hinge is meant for use with cedar, redwood, vinyl or ACQ (treated) lumber.
  • Also for use in corrosive environments or where the look of stainless steel is desired.
  • Heavy duty strap hinge. Door or gate can be lifted off after installation.
  • Made from solid stainless steel material (0.156" thickness).
  • Vertical mounting plate measures 2" wide by 6.5" tall.
  • Stainless steel wood screws are included. Also included are 1/2" x 4" stainless steel carriage bolts (one per hinge). Carriage bolts install in the square hole as a through bolt.
  • Hinge is made from Type 316 Stainless. Fasteners are made from Type 305 Stainless.
  • These hinges are sold by the pair. A pair is two hinges.
Click here for Information & Pricing

Strap Hinges, Bean Style, Heavy Duty

Strap Hinges, Bean Style, Heavy Duty
  • Strap hinges are available in either a "Rough Black Iron" or a "Smooth Black Iron" finishes.
  • Strap hinges are available in 4 lengths; 15-5/8", 19-5/8", 30" and 36". The 30" and 36" hinges are extra heavy duty hinges with a weight rating of 600 lbs per pair of hinges.
  • For interior or exterior use.
  • Hinge pin is removable.
  • Pad (small hinge leaf) is reversible for full or half-surface installation.
  • Comes complete with matching screws.
  • Weight rating is based on using 3 hinges per gate or door. For the 30" and the 36" hinges the weight rating is based on using 2 hinges per door.
  • These hinges match our other black iron hardware found in the Gate Hinges & Hardware section.

Please note: The 30", smooth black finish hinge is a Special Order item. If you place an order for this item someone from our office will contact you. The lead time is approximately 1 week.

Finishes:

  • Smooth Black Iron
  • Rough Black Iron
Click here for Information & Pricing
accredited business BBB
Sign up for email updates from HardwareSource and get 5% OFF your next order!
Email: