• Bean style strap hinge with a pintle end that fastens to wood or masonry (with masonry anchor, not included).
• This strap hinge is for heavy duty use. It can be used on a gate weighing up to 250lbs (per pair of hinges). Comes complete with 3 black carriage bolts (plus nuts and washers) and a black square head wood screw.
• Pintle style mounting allows gate to be removed by lifting off pintle.
• With "pintle style mounting" your gate can be installed so it can swing both ways (in and out) or it can be installed so that it opens only one way (either in or out).
• Normal installation requires two hinges per gate.
• "Hook Size" refers to the dimensions of the threaded portion. "Screw Size" refers to the carriage bolt dimensions.

Finishes:

• Black Iron

• Strap hinges are available in either a "Rough Black Iron" or a "Smooth Black Iron" finishes.
• Strap hinges are available in 4 lengths; 15-5/8", 19-5/8", 30" and 36". The 30" and 36" hinges are extra heavy duty hinges with a weight rating of 600 lbs per pair of hinges.
• For interior or exterior use.
• Hinge pin is removable.
• Pad (small hinge leaf) is reversible for full or half-surface installation.
• Comes complete with matching screws.
• Weight rating is based on using 3 hinges per gate or door. For the 30" and the 36" hinges the weight rating is based on using 2 hinges per door.
• These hinges match our other black iron hardware found in the Gate Hinges & Hardware section.

Finishes:

• Smooth Black Iron
• Rough Black Iron

• Strap hinges are available in two finishes. The 4 smaller sizes are a "Rough Black Iron" finish. The 2 larger sizes are a "Smooth Black Iron" finish.
• The hinge pin is removable so that the pad (smaller leaf) may be reversed. This allows the hinge to be installed as either a full-surface hinge or a half-surface hinge.
• The weight rating on the 9" and 13" hinge applies to a door with a maximum door thickness of 1-3/8" and a maximum door width of 32" using 3 hinges per door.
• The weight rating on the 17" and 20.5" hinge applies to a door with a maximum door thickness of 1-3/4" and a maximum door width of 36" using 3 hinges per door
• The 30" and 36" hinges are extra heavy duty hinges and are rated at 600# per pair of hinges.
• These hinges match our "Heart" style gate latches found in the Gate Latch and Gate Lock section of the website. Two "Heart" style latches are offered for purchase during checkout.
• Complete with screws.
• Made from steel base material.

Finishes:

• Black Iron

• Beautifully finished tee hinges with heavy black powder coating.
• Made from 1/8" thick steel.
• Strap length is measured to the center of the hinge pin.
• Matching flat head screws are included.

Finishes:

• Black Powder Coated

• Stainless steel T hinge, recommended for vinyl, redwood, cedar and ACQ (treated) lumber.
• Excellent for use anywhere that corrosion is a problem.
• Heavy duty construction, non-removeable hinge pin.
• Strap length is measured from the tip of the strap to the far end of the hinge pin barrel.
• Pad width is measured from the edge of the pad to the inside edge of the hinge pin barrel.
• Strap width means the widest part of the strap.
• Hinge is made from Type 316 Stainless. Fasteners are made from Type 305 Stainless.
• Stainless steel screws are included.
• This hinge is sold by the "Pair". A pair is 2 hinges, usually what is required to hang one door.

Finishes:

• Satin Stainless Steel

• Stainless steel strap hinge is meant for use with cedar, redwood, vinyl or ACQ (treated) lumber.
• Also for use in corrosive environments or where the look of stainless steel is desired.
• Heavy duty strap hinge. Door or gate can be lifted off after installation.
• Made from solid stainless steel material (0.156" thickness).
• Vertical mounting plate measures 2" wide by 6.5" tall.
• Stainless steel wood screws are included. Also included are 1/2" x 4" stainless steel carriage bolts (one per hinge). Carriage bolts install in the square hole as a through bolt.
• Hinge is made from Type 316 Stainless. Fasteners are made from Type 305 Stainless.
• These hinges are sold by the pair. A pair is two hinges.

• Strap side of hinge measures 3" wide and 5/32" thick and is made of plated steel
• Plate side of hinge measures 6-1/8" by 2-1/2" by 1/2" thick and is made of cast aluminum
• Hinge swings on bronze bearings
• For doors where the frame and the door are flush
• Plate side of hinge uses #14 flat head screws (not included)
• Strap side of hinge uses 3/8" bolts (not included)
• Available in two finishes: Highly polished Chrome plated or Black coated

The 12", 18" and 24" dimensions are measured from the end of the strap to the pivot point of the strap

Weight Ratings are for two hinges per door

SKU 902002 and 902010

• 250lbs for up to a 36" door and
• 200lbs for a 36" to 40" door

SKU 902004 and 902012

• 300lbs for a 36" to 40" door
• 250lbs for a 42" to 46" door

SKU 902006 and 902014

• 300lbs for up to a 48" door

• Beautiful lift-off type gate hinge with uniquely textured surface.
• Door or gate can be lifted off after installation.
• Strap is made from 2" wide by 1/4" thick steel.
• Vertical plate measures 1-3/4" by 6-1/4" by 7/32". Pintle diameter is 5/8".
• Wood screws are included.

PLEASE NOTE; the post plate and the gate plate for this hinge are offset from each other by 1/2". For most gate installations, this is not a problem. However, if you want your gate and post to be perfectly flush, you should not choose this hinge.

Finishes:

• Black Powder Coated

• Heavy duty strap hinge with Traditional British Hardware styling.
• Strap is approximately 3/16" thick and 2" wide. Hinge pin is 5/8" in diameter.
• Hardware as it is installed on post side of hinge measures approximately 6.5" tall by 2-1/4" wide.
• Black finish is a heavy black powder coating. Galvanized finish is a true heavy galvanizing suitable for outdoor use near a seacoast.
• Matching wood screws are included. One galvanized through bolt is included per hinge. Through bolt is mounted in square hole.

Finishes:

• Black Powder Coat
• Galvanized

• These are the same hinges as our "Heavy Duty British Style Strap Hinges" except they are heavier and longer.
• Extra Heavy duty strap hinge with Traditional British Hardware styling.
• Strap is approximately 7/32" thick and 2-3/4" wide. Hinge pin is 7/8" in diameter.
• Hardware as it is installed on post side of hinge measures approximately 9.5" tall by 3" wide.
• Black finish is a heavy black powder coating.
• Matching wood screws are included. One through bolt is included per hinge. Through bolt is mounted in square hole.

Finishes:

• Black Powder Coat

• Heavy duty strap hinge, door or gate can be lifted off after installation.
• Available in two finishes; powder coated black or heavy galvanized (true galvanizing not zinc plated). Galvanized models are suitable for sea coast use.
• Traditional British Hardware styling.
• Made from 3/16" thick steel.
• Vertical mounting plate sizes; For SKU 215108 it measures 1-7/16" x 5-1/4". For SKU 215130 and 215110, it measures 1.5" x 5-3/8". For SKU 215132 and 215112, it measures 2" x 6.5". For SKU 215134 and 215114, it measures 2-3/16" by 6.5". SKU 215136 vertical plate measures 8" by 2-3/16".
• Matching wood screws are included. One galvanized through bolt is included per hinge(carriage bolt; 3/8" x 4"). Through bolt is mounted in square hole.

Finishes:

• Powder Coated Black
• Galvanized

• Heavy duty strap hinge for gates, truck doors or anywhere a heavy duty stainless steel strap hinge is needed.
• Made for surface mounted flush installation.
• Made from 0.197" thick stainless steel.
• Horizontal strap measures 2.5" tall by 7-3/8" wide (measured from center of hinge pin).
• Vertical strap measures 4-1/8" tall by 2-1/4" wide (measured from center of hinge pin).
• Hinge pin is removable (held in place by a circlip). Hinge pin features a zerk fitting to allow lubrication.
• Each hinge uses 6 each 5/16" lag screws (not included but offered for purchase during checkout).

Finishes:

• Polished Stainless

• These extra heavy duty ball bearing strap hinges can hold up to a 3800 lb. gate or door. Hinge choice is based on gate width and weight. See chart at link below to assist in hinge choice and number of hinges to use.
• These are the best quality and heaviest weight strap hinges that we know of.
• Offset pintle can be set back on face of jamb or wall to allow swing clear application.
• Strap and pintle painted off-white. User can repaint with a different color if desired.
• Pintle pin & bearings are zinc plated for rust resistance.
• These hinges are made in USA.
• Pintle uses 1/2" lag screw, strap uses 3/8" lag screw (lag screws are not included with hinge).
• Click on the link below for a table that gives the weight ratings for these hinges.

Finishes:

• Painted off-white

• The "bolt" and "strap" for this hinge are ordered as separate components.
• When ordering components make sure that the "pintle" sizes match. The pintle sizes available for these components are 1/2", 5/8", 3/4" and 7/8".
• Maximum post sizes(maximum distance between the washers) for the "Bolt" are as follows; SKU 504820 is 4-5/8", SKU 504821 is 6-1/2", 504822 is 10-1/4", 504823 is 7-7/8", 504824 is 10" and 504825 is 9-7/8".
• The weight ratings listed are for one hinge. For example, if the listed weight rating is 100 lbs. and you install 2 hinges, your 2 hinges would be rated at 200 lbs.
• One hinge consists of one "strap" and one "bolt". You would normally order 2 straps and 2 bolts to hang one gate or door.
• The "straps" are normally installed using carriage bolts (not included).
• Two washers and two nuts are included with each "bolt" ordered.

PLEASE NOTE: the sizes listed as the "Pintle Diameter" (for example 3/4" Pintle) are nominal dimensions, meaning they do not measure exactly that dimension. Use our "nominal dimension" to match up our Straps with our Bolts, etc. when you are ordering our products. If you order one of our products to match a pintle diameter of something that you already own, you do so at your own risk.

Finishes:

• Zinc Chromate

• The "screw" and "strap" for this hinge are ordered as separate components.
• When ordering components make sure that the "pintle" sizes match. The pintle sizes available for these components are 1/2", 5/8", 3/4" and 7/8".
• The weight ratings listed are for one hinge. For example, if the listed weight rating is 100 lbs. and you install 2 hinges, your 2 hinges would be rated at 200 lbs.
• One hinge consists of one "strap" and one "screw". You would normally order 2 straps and 2 bolts to hang one gate or door.
• The "straps" are normally installed using carriage bolts (not included).
• Steel base material

PLEASE NOTE: the sizes listed as the "Pintle Diameter" (for example 3/4" Pintle) are nominal dimensions, meaning they do not measure exactly that dimension. Use our "nominal dimension" to match up our Straps with our Bolts, etc. when you are ordering our products. If you order one of our products to match a pintle diameter of something that you already own, you do so at your own risk.

Finishes:

• Zinc Chromate

• This is a very heavy duty hinge specially made for heavy gates and doors.
• This hinge will swing a full 180 degrees if installed without a stop.
• Hinge is made up of a mounting plate (flange) and J-Bolt arm.
• Hinge pivots on a steel ball bearing and includes a grease fitting to keep the bearing lubricated.
• Mounts with 3/8" lag screws or bolts (not included).
• The minimum gap between the post and edge of gate frame is 2-7/8" for SKU 783000.
• The maximum spread between the two nuts on the threaded part is as follows; for the 783000 it is 2-3/4".
• The thread size on our SKU 783000 is 5/8 x 11. The thread size on our SKU 783002 is 3/4 x 10.
• Weight rating is for 2 hinges.

Please note that these pivots are currently on back order with the manufacture until June. If you place an order with us we will hold your order and ship them as soon as they are back in stock.

Finish:

• Black Coated

• Non -template hinge, for wood doors
• Pivot points do not align with standard full mortise hinges. These hinges cannot be mixed with other types of hinges on the same door.
• Large diameter barrel matches older style single acting pivot hinges
• Steel base material
• The 6" and 7" size come with machine screws
• The "Size" dimension is the height of the plate that mounts on the door and jamb
• The 6" hinge maximum door weight is 125lbs using 2 hinges and 155lbs using 3 hinges.
• The 7" hinge maximum door weight is 130lbs using 2 hinges and 175lbs using 3 hinges.

Finishes:

• 601 (US1B) Bright Black Japanned
• 600 (USP) Primed for Painting.

• Large heavy duty spring hinges. Full mortise template hinges.
• Hinges measure 4-1/2" high by 4-1/2" wide (in open position as shown in photo).
• Using 3 hinges per door they will work on a maximum door weight of 150 lbs.
• Hinges are not handed. They will work on both right hand and left hand doors.
• Made from steel base material.
• Easily adjusted spring tension. Click on link below for instructions.
• Screw hole pattern conforms to ANSI specifications for template hinges. Screw hole spacing matches Architectural grade hinge template for 4-1/2" hinges.
• Pivot point aligns with non-spring hinges of the same size.
• Hinges with a SKU number that begins with 760 are "Made in America", made in USA hinges.
• Screws are included.

PLEASE NOTE: Any of the hinges listed below with an SKU number that starts with 760 is a U.L. listed Grade 1 hinge and may be used on a fire door. A minimum of two hinges per door is required for a fire door.

PLEASE NOTE BEFORE ORDERING, SEE THE "UNIT" COLUMN BELOW

• Some hinges are sold by the "Each". Each means one hinge (order 2 or 3 hinges per door).
• Some hinges are sold by the "Pair". A pair is 2 hinges. Hinges on this page may be ordered by the "Half Pair". To place an order for 1-1/2 pair (3 hinges), enter 1.5 in the order quantity.

• American made product.
• Double acting hinges for larger doors.
• Double acting spring hinges allow the door to open 180 degrees in either direction and spring action returns door to center closed position.
• Saloon Door Hinges is another name for these hinges.
• Spring tension is adjustable.
• The satin brass finish is the most popular finish. The photo above shows the zinc chromate finish.
• The manufacturer recommends using three hinges per door for heavier doors. Two hinges may be used for lighter doors. Click on the link below for more specific information. If three hinges are used the center hinge should be installed as close as possible to the top hinge for maximum support.
• The door may be mortised for these hinges so that there is no gap between the door and the door frame. If you elect not to mortise then the following door gaps apply: 6" size-.325" gap; 7" size-.352" gap; 8" size-.394" gap.
• Steel base material.
• All products on this page are made in the USA.
• Complete with wood screws.
• "Size" is the height of the plate that mounts on the door and jamb.
• This is a high quality American made product offered at a very competitive price.
• When shopping, please consider that many of our competitors are selling a cheap foreign made product at a cheap price.

*Maximum door weight (lbs.) using three spring hinges

Finishes:

• 633(US4) Satin Brass.
• 603(US2G) Zinc Chromate.
• 640(US10B) Oil Rubbed Bronze.
• 600(USP) Prime coated for painting.

• Pivot type welding hinge with roller bearings.
• Available in a 3" or a 4" size.
• The 3" size has a sealed roller bearing that measures 1-3/8" outside diameter by .622" inside diameter by .43" thick. Uses a 1/2" x 4" pivot bolt. Post side welding plate measures 1.5" x 3.5". Gate side welding plate measures 1.5" x 2.75". The spacing between the gate and post is 2.71".
• The 4" size has a sealed roller bearing that measures 1.849" outside diameter by .786" inside diameter by .55" thick. Uses a 5/8" x 5" pivot bolt. Post side welding plate measures 2" x 4.25". Gate side welding plate measures 2" x 3.25". The spacing between the gate and post is 4.25".
• Both hinges feature a 220 degree swing range. Both hinges use a nylon locking nut on the bottom of the pivot bolt.
• Made from steel base material.
• These hinges are sold by the pair which means two hinges. A pair is normally what you need to hang one gate.
• Weight ratings are based on using a pair of hinges.
• Hinges are made in the U.S.A.

Finishes:

• Painted Black

• Weld-on barrel hinge is a lift off pivot hinge.
• Features a round barrel body.
• Made from steel base material.
• Hinge pin is made from stainless steel.
• Hinge pin pivots on a ball bearing.
• Features a "zerc" type grease fitting.
• The hinge pin is fixed in one of the barrels. In the photo to the left the barrel with the fixed hinge pin is the barrel on top.
• The "Hinge Gap" is the distance between the post and the gate after the hinge is installed.
• Each hinge has 2 weldable plates. Each plate measures as follows; SKU 782000 measures 1" x 2" x 3/8" and SKU 782002 measures 1-1/2" x 3" x 3/8".
• SKU #782000 use for gates up to 8-10 feet wide
• SKU #782002 use for gates up to 15-17 feet wide

• Super heavy duty weld-on pivot hinge for very heavy gates.
• Hinge measures 7" tall by 2.5" in diameter. Each weld-on plate measures 2.75" tall by 2" wide.
• The hinge pin is made from stainless steel, is 1.25" in diameter and rides on a 1" diameter ball bearing.
• Barrels are made from cold rolled carbon steel.
• Maximum gate weight is 3000 lbs per pair of hinges.
• Includes a "zerk" type fitting so that the hinge may be lubricated with a grease gun.
• Hinges are made in the U.S.A.
• These hinges are sold by the pair which means two hinges. A pair is normally what you need to hang one gate. A pair of these hinges weighs about 22 lbs.

Finishes:

• Painted Black

• This 2-piece weld-on hinge is extremely popular because of its high weight load capacity as well as it professional appearance.
• Ideal for gates, machinery doors, barbeque pits, electrical boxes, and trailers.
• It can be welded on as a lift-off hinge or it can be permanently mounted.
• Made from mild steel (1015) with a case hardened fixed steel pin and a brass washer.
• Weight rating shown is for a pair of hinges. A pair of hinges is two hinges.
• The "S-dimension" is the diameter plus the welding area.

• 3.5" tall Gorilla Weld-on Hinge.
• For trash enclosures, gates, high security applications, prison doors and gates.
• Both sides are meant to mount to flat surfaces.
• Hinge is built to reduce the space between the jamb or post and the gate.
• Weight rated to 1000 lbs per pair of hinges.
• Made from steel and prime coated.
• Allows for 180 degree swing.
• Hardened roller bearing design
• High security welded pin design
• Includes zerk fitting for lubrication.
• These hinges are sold by the "each". You would normally order 2 hinges for each door or gate.

• Hinge will allow gate to swing open up a hill.
• Available in a Standard Duty Model and a Heavy Duty Model
• Standard Duty Model is rated for a 600 lb. gate.
• Standard Duty measurements: Bottom hinge is 12" long, Top Hinge is 6" long. Bottom and Top Hinges are 3" tall by 3" wide and made from 3/8" thick steel.
• Heavy Duty Model is rated for a 2000 lb. gate.
• Heavy Duty measurements; Bottom hinge is 12" long, Top Hinge is 6" long. Bottom and Top Hinges are 4-3/8" tall by 3-1/2" wide and made from 1/2" thick steel.
• Hinge is a "Weld on" type hinge.
• Made from steel and prime coated.
• A grease fitting allows lubrication of pivot.
• Installation instructions are included.
• Click on link below to see installation instructions.
• Sold by the pair. A pair of hinges will hang one gate.
• A pair is made up of a top hinge (the shorter of the two hinges) and a bottom hinge.

• Heavy duty weld on hinges made with dependable roller bearing design.
• Roller bearings are made using a hardened steel inner race and a hardened steel roller cage bearing held in place with a Grade 5, zinc plated bolt.
• Hinge is fitted with a grease fitting for applying periodic lubrication.
• Hinge features a very large weld surface for maximum weight bearing.
• Available in two weight ratings; 1000 lbs per pair of hinges and 3000 lbs per pair of hinges.
• Click on links below for dimension diagrams of each hinge.
• Hinges are prime coated, ready for painting after installation.
• Hinges are sold by the each. Order a minimum of two hinges per door or gate.

• heavy duty weld-on hinges
• fast spun pin
• for heavy duty applications
• not swaged for mortising
• no holes
• hinge widths are approximately 1/8" less than nominal sizes shown
• all sizes have five knuckles

• Heavy duty blank weld-on hinges.
• Hinge pin is removable.
• Non-swagged heavy hinge is designed for surface application by welding on metal.
• Made from cold rolled steel, not plated.
• All sizes have 5 knuckles.
• Weight rating applies to the use of 1, 2 or 3 hinges per hinged device. For example if the weight rating for one hinge is 40 lbs then the weight rating for 3 hinges is 120lbs. The weight ratings are do not apply to the use of more than 3 hinges.

Finishes:

• Natural

• Weld-on barrel hinge is a lift off pivot hinge.
• Features a round barrel body.
• Made from steel base material and plated with a bright zinc plating.
• Hinge pin pivots on a ball bearing.
• Features a "zerc" type grease fitting to keep the bearing lubricated.
• The hinge pin is fixed in one of the barrels. In the photo to the left the barrel with the fixed hinge pin is the barrel on top.
• The "Hinge Gap" is the distance between the post and the gate after the hinge is installed.
• Each hinge has 2 weldable plates. Each plate measures as follows; SKU 782500 measures 7/8" x 2" x 5/16" and SKU 782510 measures 1-3/4" x 3" x 3/16".
• SKU #782500 use for gates up to 6-8 feet wide
• SKU #782510 use for gates up to 12-15 feet wide

Finishes:

• This 2-piece weld-on hinge is extremely popular because of its high weight load capacity as well as it professional appearance.
• Ideal for gates, machinery doors, barbeque pits, electrical boxes, and trailers.
• It can be welded on as a lift-off hinge or it can be permanently mounted.
• Made from stainless steel (Type 304) with a case hardened fixed stainless steel pin and a stainless steel washer.
• Weight rating shown is for a pair of hinges. A pair of hinges is two hinges.
• The "S-dimension" is the diameter plus the welding area.

• Stainless steel flag hinge for welding.
• Made from type 304 stainless steel.
• Hinge is 6" tall by 2.5" wide. Click on link below for more dimensions.
• Hinge pin is fixed in bottom leaf. Top leaf will "lift off" bottom leaf.
• Top leaf rides on a ball bearing fixed to the top of the hinge pin.
• A pair of these hinges has a weight rating of 198 lbs.
• These hinges are available in either a Left Hand or Right Hand model as shown in photo.
• These hinges are sold by the "each". You would normally order 2 hinges per door you are hinging.

Finishes:

• Satin Stainless Steel

• Plain steel base material, not plated.
• Knuckle length is 2".
• Hinge pin diameter is 3/8".
• Economical for use where a strong hinge is needed and corrosion will not be a problem.
• PLEASE NOTE! If you would like your piano hinge cut to a specific size, let us know in the comment box when you check out. You can save the "UPS oversize charge" by having your hinge cut to a size below 52". If we cut your piano hinge, we will ship all pieces. The first cut on each piece of hinge is free. Each additional cut is $3.00 (limit 5 cuts per hinge).
• PLEASE NOTE: PIANO HINGE 52" OR LONGER IS CONSIDERED OVERSIZE BY UPS. AN ADDITIONAL $8.95 CHARGE WILL BE ADDED TO ANY PIANO HINGE WHICH IS SHIPPED 52" OR LONGER.YOU WILL ONLY BE CHARGED ONE $8.95 CHARGE PER ORDER.
• Cut piano hinge may not be returned.

• Heavy duty butt hinge (8 inches by 8 inches) made for heavy doors and gates.
• Hinge is designed to be installed as a full mortise hinge.
• Hinge measures 8 inches tall by 8 inches wide in the open position (as shown in photo).
• Made from extra thick steel material. Thickness of steel is 0.200".
• Hinge features 4 ball bearings (maintenance free bearings).
• Each hinges uses 16 each #14 wood screws (included).
• Hinge is capable of holding up to an 800lb. door (depending on width of door and number of hinges used, see info below).
• Hinge fits door thicknesses of 2-1/4" to 3".
  • Weight Rating for Hinge
    • For door width up to 3 feet: 800 lbs.
    • For door width 3 feet to 3.5 feet: 670 lbs.
    • For door width 3.5 feet to 4 feet: 600 lbs.
  • Number of Hinges per Door
    • Up to 5 feet high, use 2 hinges
    • From 5 feet high to 7.5 feet high, use 3 hinges
    • From 7.5 feet high to 10 feet high, use 4 hinges
    • From 10 feet high to 12.5 feet high, use 5 hinges
    • From 12.5 feet high to 15 feet high, use 6 hinges
• PLEASE NOTE: weight ratings given are a general guide for doors used in residential (low frequency) use under normal situations. The weight of the door, the width of the door and the number of hinges on the door are the major factors that affect hinge selection. When selecting hinges for your door keep in mind that other factors such as abuse, impacts, hostile atmospheres and other similar conditions can affect the choice of hinges.

Available Finishes

• Primed for Painting
• Oil Rubbed Bronze
• Satin Chrome

• Beautiful solid brass heavy duty ball bearing butt hinges.
• Heavy duty butt hinge made for heavy doors and gates.
• Hinge is designed to be installed as a full mortise hinge.
• Hinge measures 6 inches tall by 6 inches wide in the open position (as shown in photo).
• Made from extra thick solid brassmaterial. Thickness ofbrass is 0.205".
• Hinge features 4 ball bearings (maintenance free bearings).
• Each hinges uses 10 each #14 x 1-1/2" wood screws (included).
• Hinge is capable of holding up to a 600 lb. door (depending on width of door and number of hinges used, see info below).
• Hinge fits door thicknesses of 2" to 2-3/4".
  • Weight Rating for Hinge
    • For door width up to 3 feet: 600 lbs.
    • For door width 3 feet to 3.5 feet: 500 lbs.
    • For door width 3.5 feet to 4 feet: 400 lbs.
  • Number of Hinges per Door
    • Up to 5 feet high, use 2 hinges
    • From 5 feet high to 7.5 feet high, use 3 hinges
    • From 7.5 feet high to 10 feet high, use 4 hinges
    • From 10 feet high to 12.5 feet high, use 5 hinges
    • From 12.5 feet high to 15 feet high, use 6 hinges
• PLEASE NOTE: weight ratings given are a general guide for doors used in residential (low frequency) use under normal situations. The weight, width and number of hinges on the door are the major factors that affect hinge selection. When selecting hinges for your door keep in mind that other factors such as abuse, impacts, hostile atmospheres and other similar conditions can affect the choice of hinges.
• ADVISORY: These solid brass ball bearing hinges contain ball bearings and the bearing raceway (madeof steel)that will eventually rust if subjected to harsh weather conditions (especially marine weather and salt air conditions).
• Optional Ball Tips are available for these hinges in matching finishes. They are offered for purchase during checkout.

HALF PAIRS. Please note the UNIT when ordering hinges. We sell the hinges depending on how the manufacturer sells them to us. In this section if a hinge is sold by the PAIR you may order by the half pair. For example if you want 3 hinges order 1.5 pair when you check out.

Available Finishes

• Polished Brass
• Oil Rubbed Bronze
• Satin Chrome

• Heavy duty butt hinge made for heavy doors and gates.
• Hinge is designed to be installed as a full mortise hinge.
• Hinge measures 6 inches tall by 6 inches wide in the open position (as shown in photo).
• Made from extra thick steel material. Thickness of steel is 0.203".
• Hinge features 4 ball bearings (maintenance free bearings).
• Each hinges uses 10 each #14 wood screws (included).
• Hinge is capable of holding up to a 600 lb. door (depending on width of door and number of hinges used, see info below).
• Hinge fits door thicknesses of 2" to 2-3/4".
  • Weight Rating for Hinge
    • For door width up to 3 feet: 600 lbs.
    • For door width 3 feet to 3.5 feet: 500 lbs.
    • For door width 3.5 feet to 4 feet: 400 lbs.
  • Number of Hinges per Door
    • Up to 5 feet high, use 2 hinges
    • From 5 feet high to 7.5 feet high, use 3 hinges
    • From 7.5 feet high to 10 feet high, use 4 hinges
    • From 10 feet high to 12.5 feet high, use 5 hinges
    • From 12.5 feet high to 15 feet high, use 6 hinges
• PLEASE NOTE: weight ratings given are a general guide for doors used in residential (low frequency) use under normal situations. The weight, width and number of hinges on the door are the major factors that affect hinge selection. When selecting hinges for your door keep in mind that other factors such as abuse, impacts, hostile atmospheres and other similar conditions can affect the choice of hinges.

Available Finishes

• Primed for Painting
• Oil Rubbed Bronze
• Satin Chrome

• Stainless steel flag hinge for welding.
• Made from type 304 stainless steel.
• Hinge is 4" tall by 2.5" wide. Click on link below for more dimensions.
• Hinge pin is fixed in bottom leaf. Top leaf will "lift off" bottom leaf.
• Top leaf rides on a ball bearing fixed to the top of the hinge pin.
• A pair of these hinges has a weight rating of 88 lbs.
• These hinges are available in either a Left Hand or Right Hand model as shown in photo.
• These hinges are sold by the "each". You would normally order 2 hinges per door you are hinging.

Finishes:

• Satin Stainless Steel

• Heavy duty blank weld-on hinges.
• Fast-spun pin, non-removeable.
• Non-swagged heavy hinge is designed for surface application by welding on metal.
• Made from cold rolled steel, not plated.
• All sizes have 5 knuckles.
• Weight rating applies to the use of 1, 2 or 3 hinges per hinged device. For example if the weight rating for one hinge is 40 lbs then the weight rating for 3 hinges is 120lbs. The weight ratings are do not apply to the use of more than 3 hinges.

Finishes:

• Natural

• Heavy duty livestock gate hinge for use on 2" (outside diameter) round tube gates.
• Pintle side of hinge "through-bolts" to the gate post with a 12.5" long bolt (3/4" diameter). Maximum post size is 9.5" in width. Pintle size is 7/8" x 2".
• Carriage bolts, nuts, and washers are included.
• These hinges are sold by the pair. A pair is usually what is required to hang one gate.
• PLEASE NOTE: the green tubing and wooden post shown in the photo are for illustrative purposes and are not included with the hinge.

Finishes:

• Zinc Chromate Plated