• Hinge is made from stamped stainless steel.
• Stainless steel is Type 304.
• To install this hinge you should mortise theinstallation areato accept the hinge knuckle and hinge leaves. This will allow a flush installation.
• Joint length means measurement along the hinge pin.
• 1/16" materialthickness.
• Uses 6 each #8 flat head screws (not included). Flat head stainless steel screws are offered for purchase during checkout.

Finishes:

• Polished Stainless Steel

• Stainless steel hatch spring support holds hatch in the open position.
• Made from type 304 stainless steel.
• Overall length is 11-3/8". Spring diameter is 9/16".
• Bracket that installs on underside of hatch measures 1-13/32" x 11/16".
• Side mounted bracket measures approximately 2" x 1-1/4".
• Uses four each #10 pan head screws (not included but offered for purchase during checkout).

• A flush ring pull allows you to mortise the pull into the door so that it is completely flush with the door surface.
• Available in two sizes; Small and Large.
• The Small size measures 1-3/8" wide by 1-3/4" tall by 7/16" thick (approximate mortise depth).
• The Large size measures 1-15/16" wide by 2-1/2" tall by 1/2" thick (approximate mortise depth).
• Made from solid brass base material.
• Matching wood screws are included.

Finishes:

• Satin Nickel
• Oil Rubbed Bronze
• Polished Brass

• Hinge measures 3-1/4" in the open position.
• Hinge measures 1-3/16" wide.
• Hinge is 1/16" thick (11/32" at the thickest point). Thickest point measurement is taken with the hinge in its flat position.
• Made from Type 304 stainless steel.
• Hinge incorporates a stop which holds the hinge flat in the horizontal position.
• Hinge mortises flush into surface of table.
• Hinge folds back a full 180 degrees onto the table.
• Uses #6 flat head screws (not included). Stainless steel screws are offered for purchase during checkout.

Finishes:

• Polished

• Hinge is installed in a mortise (cutout) in a hatch and hatch frame so that the hinge is flush with the hatch surface.
• Hatch hinge measures 2-7/8" in open position.
• Hinge is 1-1/2" wide (measurement along hinge pin).
• Made from type 304 stainless steel.
• Uses #6 flat head screws (not included but offered for purchase during checkout).

Finishes:

• Polished Stainless Steel

• Hinge to be installed flush with the surface of a hatch.
• Hinge installs in a mortise (cutout) so that it will be completely flush with the surface.
• Hinge measures 1-1/2" in width (measurement along the hinge pin).
• Hinge measure 1-7/8" in length.
• Uses #8 flat head wood screw (not included but offered for purchase during checkout).
• PLEASE NOTE: this hinge is made from stainless steel and powder coated black. We have not been able to find any manufacturer that makes a stainless steel screw with a black coating. We are offering two different screws during checkout. One screw is a stainless steel flat head screw (not coated black). You could paint the head of the stainless steel screw black after installation to match the black powder coat of the hinge.
• The other option we are offering is a steel #8 flat head screw which comes with a black coated head. This would be a good choice for when this hinge is not used in an area subject to corrosion.

• Made for boat hatches and other hatch covers.
• Hinge is made for hatch covers that are flush with what they are hinged to.
• Hinge may be taken apart by removing clevis pin.
• Clevis pin is secured by a stainless ring.
• Made from polished stainless steel (Type 316 Stainless Steel).
• Uses #10 flat head stainless steel screws (not included but offered for purchase during checkout).
• Hinge is sold by the each. You would normally order two hinges per hatch.
• Click on link for hinge dimensions.
• PLEASE NOTE: this hinge is designed with a fairly loose fit so that it is easy to remove the clevis pin.

• Flush pull for hatches.
• Flush pull installs completely flush with the surface of the hatch by mortising into the hatch.
• Mortise depth is 3/8".
• Flush pull measures 3" wide by 2-1/4" tall.
• Pull is spring loaded so that when it is released it returns to the flush or down position.
• Made from polished stainless steel.
• Uses #8 flat head screws (not included but offered for purchase during checkout).