• Heavy duty strap hinge, door or gate can be lifted off after installation.
• Available in two finishes; powder coated black or heavy galvanized (true galvanizing not zinc plated). Galvanized models are suitable for sea coast use.
• Traditional British Hardware styling.
• Made from 3/16" thick steel.
• Vertical mounting plate sizes; For SKU 215108 it measures 1-7/16" x 5-1/4". For SKU 215130 and 215110, it measures 1.5" x 5-3/8". For SKU 215132 and 215112, it measures 2" x 6.5". For SKU 215134 and 215114, it measures 2-3/16" by 6.5". SKU 215136 vertical plate measures 8" by 2-3/16".
• Matching wood screws are included. One galvanized through bolt is included per hinge(carriage bolt; 3/8" x 4"). Through bolt is mounted in square hole.

Finishes:

• Powder Coated Black
• Galvanized

• Heavy duty strap hinge with Traditional British Hardware styling.
• Strap is approximately 3/16" thick and 2" wide. Hinge pin is 5/8" in diameter.
• Hardware as it is installed on post side of hinge measures approximately 6.5" tall by 2-1/4" wide.
• Black finish is a heavy black powder coating. Galvanized finish is a true heavy galvanizing suitable for outdoor use near a seacoast.
• Matching wood screws are included. One galvanized through bolt is included per hinge. Through bolt is mounted in square hole.

Finishes:

• Black Powder Coat
• Galvanized

• These are the same hinges as our "Heavy Duty British Style Strap Hinges" except they are heavier and longer.
• Extra Heavy duty strap hinge with Traditional British Hardware styling.
• Strap is approximately 7/32" thick and 2-3/4" wide. Hinge pin is 7/8" in diameter.
• Hardware as it is installed on post side of hinge measures approximately 9.5" tall by 3" wide.
• Black finish is a heavy black powder coating.
• Matching wood screws are included. One through bolt is included per hinge. Through bolt is mounted in square hole.

Finishes:

• Black Powder Coat

• Strap angle is adjustable to fit gates and doors with curved edges.
• Hinge has a true galvanized finish (not zinc chromate plated), suitable for use around a sea coast.
• Hinge strap is approximately 2-1/4" wide by 3/16" thick.
• Vertical wing measures approximately 8" tall by 2-1/2" wide.
• Angle of strap may be set at any angle from horizontal to 90 degrees up or down.
• Made from steel base material.
• Wood screws are provided for the vertical wing and 9/16" x 4" carriage bolts are provided for the strap.

Finishes:

• Galvanized

• Beautiful lift-off type gate hinge with uniquely textured surface.
• Door or gate can be lifted off after installation.
• Strap is made from 2" wide by 1/4" thick steel.
• Vertical plate measures 1-3/4" by 6-1/4" by 7/32". Pintle diameter is 5/8".
• Wood screws are included.

PLEASE NOTE; the post plate and the gate plate for this hinge are offset from each other by 1/2". For most gate installations, this is not a problem. However, if you want your gate and post to be perfectly flush, you should not choose this hinge.

Finishes:

• Black Powder Coated

• Strap side of hinge measures 3" wide and 5/32" thick and is made of plated steel
• Plate side of hinge measures 6-1/8" by 2-1/2" by 1/2" thick and is made of cast aluminum
• Hinge swings on bronze bearings
• For doors where the frame and the door are flush
• Plate side of hinge uses #14 flat head screws (not included)
• Strap side of hinge uses 3/8" bolts (not included)
• Available in two finishes: Highly polished Chrome plated or Black coated

The 12", 18" and 24" dimensions are measured from the end of the strap to the pivot point of the strap

Weight Ratings are for two hinges per door

SKU 902002 and 902010

• 250lbs for up to a 36" door and
• 200lbs for a 36" to 40" door

SKU 902004 and 902012

• 300lbs for a 36" to 40" door
• 250lbs for a 42" to 46" door

SKU 902006 and 902014

• 300lbs for up to a 48" door

• These extra heavy duty ball bearing strap hinges can hold up to a 3800 lb. gate or door. Hinge choice is based on gate width and weight. See chart at link below to assist in hinge choice and number of hinges to use.
• These are the best quality and heaviest weight strap hinges that we know of.
• Offset pintle can be set back on face of jamb or wall to allow swing clear application.
• Strap and pintle painted off-white. User can repaint with a different color if desired.
• Pintle pin & bearings are zinc plated for rust resistance.
• These hinges are made in USA.
• Pintle uses 1/2" lag screw, strap uses 3/8" lag screw (lag screws are not included with hinge).
• Click on the link below for a table that gives the weight ratings for these hinges.

Finishes:

• Painted off-white

• Strap side of hinge measures 2-1/2" wide by 9" long by 5/8" thick cast aluminum
• Plate side of hinge measures 4-5/8" high by 2-3/4" wide by 3/8" thick
• Hinge swings on bronze bearings
• Each hinges uses 8 each #14 flat head screws (not included)
• For doors where the frame and door are flush with each other
• The hinges are rated at 200 lbs for a pair of hinges on a door up to 36" wide

Finishes:

• Polished aluminum
• Flat Black

• Stainless steel strap hinge is meant for use with cedar, redwood, vinyl or ACQ (treated) lumber.
• Also for use in corrosive environments or where the look of stainless steel is desired.
• Heavy duty strap hinge. Door or gate can be lifted off after installation.
• Made from solid stainless steel material (0.156" thickness).
• Vertical mounting plate measures 2" wide by 6.5" tall.
• Stainless steel wood screws are included. Also included are 1/2" x 4" stainless steel carriage bolts (one per hinge). Carriage bolts install in the square hole as a through bolt.
• Hinge is made from Type 316 Stainless. Fasteners are made from Type 305 Stainless.
• These hinges are sold by the pair. A pair is two hinges.

• 24 Inch Fieldgate hinge is a heavy duty strap pintle type hinge for large gates.
• Hinge set is made up of an upper and a lower hinge.
• The upper hinge is 24" in length overall. Built to fit a 3" thick gate. Straps wrap around both sides of the gate and are held in place with 3 carriage bolts (included).
• The lower hinge is 6.5" in length overall. Built to fit a 3" thick gate. Straps wrap around both sides of the gate and are held in place with one carriage bolt (included).
• Both the upper and lower hinge ride on a 3/4" diameter by 2.5" pintle.
• The upper pintle through-bolts through the gate post. Fits a gate post up to 5.5" thick.
• The lower pintle has a sharp pointed end which pushes into the gate post.
• A hinge set includes an upper and a lower hinge and will hinge one gate.
• A set of these hinges (top pivot and bottom pivot in combination) will hold up to a 140 lb. gate.
• Made from steel base material and black powder coated.

Important Installation Infromation

• The large 24" hinge must be installed as the top hinge.
• The smaller 6.5" hinge must be installed as the bottom hinge.
• The top hinge is held in place with a through-bolt, nut and square plate.
• The bottom hinge is secured by a spike which is held in place by friction and gravity.

• Solid bronze strap hinge for use in coastal areas or anywhere a rustic old world design is desired. From our "Solid Bronze Collection".
• Hinge strap measures approximately 12" in length. Width of hinge strap is 1-1/4". Thickness of strap is approximately 5/16".
• Pintle plate measures 3-3/4" by 1-1/4".
• Stainless steel wood screws are included. Screws are coated with a matching bronze finish.
• Bronze is an old world material that does not deteriorate in coastal or other regions. The Bronze finish, however, is a "living" finish. Please read more about this by clicking on the link.
• PLEASE NOTE: This hinge is made up of two parts that must be ordered separately; the pintle plate and the hinge strap. Please make sure to order one pintle plate and one hinge strap to make up each hinge that you intend to order.

• This very high quality solid bronze strap hinge is made for use in coastal areas or anywhere a rustic old world design is desired. From our "Solid Bronze Collection".
• This product is sold in components. The components consist of 2 items; a "Strap" which attaches to the gate surface and a pintle which attaches to the post. The pintle is available as either a "Plate Pintle" a "Screw-in Pintle" or a "Jam Pintle".
• The "Plate Pintle" measures 2" wide by 6-1/4" tall. The plate material is about 1/4" thick. The pintle portion is 11/16" in diameter by 2" tall.
• The "Screw-In Pintle" is available in two sizes, Small and Large. The small size measures 5" horizontally and 3-3/8" vertically. The pintle portion is 11/16" in diameter by 2" tall. The screw thread portion is 3-1/4" by 11/16". The large size measures 7.5" horizontally and 3-7/8" vertically. The pintle portion is 11/16" in diameter by 2" tall. The screw thread portion is 6" by 13/16".
• The "Jam Pintle" is meant to be installed in the jamb or edge of the door frame or gate post and can be installed in a mortise (cutout). The mounting plate portion of the "Jam Pintle" measures 4-3/4" wide by 2-7/16" tall by 9/32" thick. The pintle is 2" tall by 11/16" in diameter. It is available in a Right Hand Model and a Left Hand Model. The image in the photo shows a Right Hand Model. Here is how the handing works: Go to the side of the gate or door where the hinges are visible (the hinged side of the door), stand with your back against the gate or door. If you want the hinges on your right then you should order the Right Hand Model. If you want your hinges on your left then you should order the Left Hand Model.
• Lag screws (1-1/2" long)are included for the "Plate Pintle", flat head wood screws are included for the "Jam Pintle". Screws are made from stainless steel and coated black.
• Two hinges will support a 150 lb. gate or door. Three hinges will support a 250 lb. gate or door.
• Bronze is an old world material that does not deteriorate in coastal or other regions. The Bronze finish, however, is a "living" finish. Please read more about this by clicking on the link.

Finishes:

• Natural Solid Bronze

• Heavy duty strap hinge for gates, truck doors or anywhere a heavy duty stainless steel strap hinge is needed.
• Made for surface mounted flush installation.
• Made from 0.197" thick stainless steel.
• Horizontal strap measures 2.5" tall by 7-3/8" wide (measured from center of hinge pin).
• Vertical strap measures 4-1/8" tall by 2-1/4" wide (measured from center of hinge pin).
• Hinge pin is removable (held in place by a circlip). Hinge pin features a zerk fitting to allow lubrication.
• Each hinge uses 6 each 5/16" lag screws (not included but offered for purchase during checkout).

Finishes:

• Polished Stainless

• Stainless steel strap hinge made for surface mounted installations.
• Hinge measures 3-1/8" tall by 5" wide.
• Made from type 304 stainless steel.
• Each hinge uses 4 each #14 pan head screws (not included but offered for purchase during checkout).

Finishes:

• Natural Stainless Steel

• Beautifully polished stainless steel strap hinge, made from Type 304 stainless steel.
• Horizontal strap measures 3.5" from center of hinge pin to end of strap.
• Vertical strap measures 2-1/4" tall by 1-3/8" from center of hinge pin to edge of strap.
• Thickness is 0.135".
• Hinge is designed for flush installation (surface mounted).
• Each hinge uses 4 each #14 pan head screws (not included but offered for purchase during checkout).

Finishes:

• Polished Stainless Steel