• Dummy straps install on the face of any door or gate to give the look of decorative strap hinges.
• The 5 smaller sized straps have a rough black iron finish. The 30" and 36" have a smooth black iron finish. Both finishes give a black wrought iron look.
• Decorative "Heart" styling.
• Steel base material and attachment screws are included.
• These dummy straps match the "Heart" style gate latches found in our Gate Latch and Gate Lock section.
• PLEASE NOTE: the two largest size straps (30" and 36") are a very heavy duty strap that is two times thicker than the other straps listed here (5/16" thick).

Finishes:

• Black Iron

• Strap hinges are available in two finishes. The 4 smaller sizes are a "Rough Black Iron" finish. The 2 larger sizes are a "Smooth Black Iron" finish.
• The hinge pin is removable so that the pad (smaller leaf) may be reversed. This allows the hinge to be installed as either a full-surface hinge or a half-surface hinge.
• The weight rating on the 9" and 13" hinge applies to a door with a maximum door thickness of 1-3/8" and a maximum door width of 32" using 3 hinges per door.
• The weight rating on the 17" and 20.5" hinge applies to a door with a maximum door thickness of 1-3/4" and a maximum door width of 36" using 3 hinges per door
• The 30" and 36" hinges are extra heavy duty hinges and are rated at 600# per pair of hinges.
• These hinges match our "Heart" style gate latches found in the Gate Latch and Gate Lock section of the website. Two "Heart" style latches are offered for purchase during checkout.
• Complete with screws.
• Made from steel base material.

Finishes:

• Black Iron

• Heart style strap hinge with a pintle end that fastens to wood or masonry (with masonry anchor, not included)
• This strap hinge is for heavy duty use. It can be used on a gate weighing up to 250lbs (per pair of hinges). Comes complete with 3 black carriage bolts (plus nuts and washers) and a black square head wood screw
• Pintle style mounting allows gate to be removed by lifting off pintle
• With "pintle style mounting" your gate can be installed so it can swing both ways (in and out) or it can be installed so that it opens only one way (either in or out).
• Normal installation requires two hinges per gate
• "Hook Size" refers to the dimensions of the threaded portion. "Screw Size" refers to the carriage bolt dimensions.
• Be sure to see our section "OTHER GATE ITEMS" for gate latches, handles and cane bolts in the same style

Finishes:

• Black Iron

• Heart style strap hinge with a pintle end
• Pintle end fastens to wood or masonry (with masonry anchor not included)
• Comes complete with black square head wood screws
• This hinge can be used on a gate weighing up to 175lbs (per pair of hinges).
• Pintle style mounting allows gate to be removed by lifting off pintle
• With "pintle style mounting" your gate can be installed so it can swing both ways (in and out) or it can be installed so that it opens only one way (either in or out).
• Normal installation requires two hinges per gate
• "Hook Size" refers to the dimensions of the threaded portion.
• Be sure to see our section "OTHER GATE ITEMS" for gate latches, handles and cane bolts in the same style

Finishes:

• Black Iron

• Dummy straps install on the face of any door or gate to give the look of decorative strap hinges.
• Decorative "Bean" styling.
• Please note that some strap lengths are available in a rough black iron finish and some are available in a smooth black iron finish. Both finishes give a black wrought iron look.
• Attachment fasteners are included. Style of attachment varies. Please see link below for a schedule of included fasteners.
• Made from steel base material.
• Be sure to see our Gate Latch and Gate Lock section for more matching "Black Iron Hardware".
• PLEASE NOTE: the two largest size straps (30" and 36") are a very heavy duty strap that is two times thicker than the other straps listed here (5/16" thick).

Finishes:

• Smooth Black Iron
• Rough Black Iron

• Strap hinges are available in either a "Rough Black Iron" or a "Smooth Black Iron" finishes.
• Strap hinges are available in 4 lengths; 15-5/8", 19-5/8", 30" and 36". The 30" and 36" hinges are extra heavy duty hinges with a weight rating of 600 lbs per pair of hinges.
• For interior or exterior use.
• Hinge pin is removable.
• Pad (small hinge leaf) is reversible for full or half-surface installation.
• Comes complete with matching screws.
• Weight rating is based on using 3 hinges per gate or door. For the 30" and the 36" hinges the weight rating is based on using 2 hinges per door.
• These hinges match our other black iron hardware found in the Gate Hinges & Hardware section.

Finishes:

• Smooth Black Iron
• Rough Black Iron

• For interior or exterior use
• Hinge pin is removable
• Pad is reversible for full or 1/2 surface installation
• Weight rating is based on using 3 hinges per gate or door.
• Comes complete with matching screws
• Be sure to see our other Black Iron Gate Hardware in the sections entitled "Gate Latches and Handles" and "Other Gate Hardware"

Finishes:

• Smooth Black Iron

• False Straps for use with butt style hinges
• Dummy straps are made from steel except for SKU 778264 and SKU 778266 which are made from cast aluminum. All have a smooth black iron finish.
• Spear shape at one end
• Complete with matching wood screws
• Be sure to see our other matching black iron hardware in the "Gate Latches & Handles" and the "Other Gate Hardware" sections.

Finishes:

• Smooth Black Iron

• Bean style strap hinge with a pintle end
• Pintle end fastens to wood or masonry (with masonry anchor not included)
• Comes complete with black wood screws to attach to gate side
• This hinge can be used on a gate weighing up to 175lbs (per pair of hinges).
• Pintle style mounting allows gate to be removed by lifting off pintle
• With "pintle style mounting" your gate can be installed so it can swing both ways (in and out) or it can be installed so that it opens only one way (either in or out).
• Normal installation requires two hinges per gate
• "Hook Size" refers to the dimensions of the threaded portion.
• This "Bean" style hinge matches other products on our website that are in the "Bean" style. Some are offered for purchase during checkout.

Finishes:

• Black Iron

• Heavy duty strap hinge, door or gate can be lifted off after installation.
• Available in two finishes; powder coated black or heavy galvanized (true galvanizing not zinc plated). Galvanized models are suitable for sea coast use.
• Traditional British Hardware styling.
• Made from 3/16" thick steel.
• Vertical mounting plate sizes; For SKU 215130 and 215110, it measures 1.5" x 5-3/8". For SKU 215132 and 215112, it measures 2" x 6.5". For SKU 215134 and 215114, it measures 2-3/16" by 6.5". SKU 215136 vertical plate measures 8" by 2-3/16".
• Matching wood screws are included. One galvanized through bolt is included per hinge(carriage bolt; 3/8" x 4"). Through bolt is mounted in square hole.

Finishes:

• Powder Coated Black
• Galvanized

• Heavy duty strap hinge with Traditional British Hardware styling.
• Strap is approximately 3/16" thick and 2" wide. Hinge pin is 5/8" in diameter.
• Hardware as it is installed on post side of hinge measures approximately 6.5" tall by 2-1/4" wide.
• Black finish is a heavy black powder coating. Galvanized finish is a true heavy galvanizing suitable for outdoor use near a seacoast.
• Matching wood screws are included. One galvanized through bolt is included per hinge. Through bolt is mounted in square hole.

Finishes:

• Black Powder Coat
• Galvanized

• Strap angle is adjustable to fit gates and doors with curved edges.
• Hinge has a true galvanized finish (not zinc chromate plated), suitable for use around a sea coast.
• Hinge strap is approximately 2-1/4" wide by 3/16" thick.
• Vertical wing measures approximately 8" tall by 2-1/2" wide.
• Angle of strap may be set at any angle from horizontal to 90 degrees up or down.
• Made from steel base material.
• Wood screws are provided for the vertical wing and 9/16" x 4" carriage bolts are provided for the strap.

Finishes:

• Galvanized

• Ornamental strap hinge is meant to be surface mounted.
• Strap measures 15" long and 6" at its widest point.
• Hinge leaf measures 4" tall by 1-3/8".
• Matching flat head wood screws are included.
• Made from steel base material.

Finishes:

• Black Powder Coated

• Ornamental strap hinge is meant to be surface mounted (door and frame are flush with each other).
• Available in two lengths; an 11" strap length and an 18" strap length (measured from tip to center of hinge pin).
• Hinge leaf measures 4" tall.
• Matching flat head wood screws are included.
• Made from steel base material and powder coated black to resist corrosion.

Finishes:

• Black Powder Coated

• Beautiful lift-off type gate hinge with uniquely textured surface.
• Door or gate can be lifted off after installation.
• Strap is made from 2" wide by 1/4" thick steel.
• Vertical plate measures 1-3/4" by 6-1/4" by 7/32". Pintle diameter is 5/8".
• Wood screws are included.

PLEASE NOTE; the post plate and the gate plate for this hinge are offset from each other by 1/2". For most gate installations, this is not a problem. However, if you want your gate and post to be perfectly flush, you should not choose this hinge.

Finishes:

• Black Powder Coated

• Bean style strap hinge with a pintle end that fastens to wood or masonry (with masonry anchor, not included).
• This strap hinge is for heavy duty use. It can be used on a gate weighing up to 250lbs (per pair of hinges). Comes complete with 3 black carriage bolts (plus nuts and washers) and a black square head wood screw.
• Pintle style mounting allows gate to be removed by lifting off pintle.
• With "pintle style mounting" your gate can be installed so it can swing both ways (in and out) or it can be installed so that it opens only one way (either in or out).
• Normal installation requires two hinges per gate.
• "Hook Size" refers to the dimensions of the threaded portion. "Screw Size" refers to the carriage bolt dimensions.

Finishes:

• Black Iron

• steel base material
• coated with a durable black finish
• reversible pin provides for right or left hand applications
• post leaf is 4"
• strap length is 7-11/16"
• complete with lag screws

Finishes:

• Black Coated

• Hinge features a decorative scalloped design.
• Made from steel base material.
• Hinge is coated with a durable black finish.
• Features a special bearing to give extended service.
• Complete with screws.
• PLEASE NOTE: The "Size" refers to the length of one hinge leaf. The "Size Open" dimension is the tip-to-tip" measurement when the hinge is in the open position as shown in the photo.

Finishes:

• Black Coated

• steel base material
• coated with a durable black finish
• reversible pin provides for right or left hand installations
• post leaf is 4-7/16"
• strap length is 8"
• complete with lag screws

Finishes:

• Black Coated

• heavy duty construction minimizes gate sag
• durable black finish
• reversible pin provides for right or left hand applications
• steel base material
• complete with lag screws

Finishes:

• Black Coated

• These extra heavy duty ball bearing strap hinges can hold up to a 3800 lb. gate or door. Hinge choice is based on gate width and weight. See chart at link below to assist in hinge choice and number of hinges to use.
• These are the best quality and heaviest weight strap hinges that we know of.
• Offset pintle can be set back on face of jamb or wall to allow swing clear application.
• Strap and pintle painted off-white. User can repaint with a different color if desired.
• Pintle pin & bearings are zinc plated for rust resistance.
• These hinges are made in USA.
• Pintle uses 1/2" lag screw, strap uses 3/8" lag screw (lag screws are not included with hinge).
• Click on the link below for a table that gives the weight ratings for these hinges.

Finishes:

• Painted off-white

• Strap side of hinge measures 3" wide and 5/32" thick and is made of plated steel
• Plate side of hinge measures 6-1/8" by 2-1/2" by 1/2" thick and is made of cast aluminum
• Hinge swings on bronze bearings
• For doors where the frame and the door are flush
• Plate side of hinge uses #14 flat head screws (not included)
• Strap side of hinge uses 3/8" bolts (not included)
• The 12", 18" and 24" dimensions are measured from the end of the strap to the pivot point of the strap

Weight Ratings are for two hinges per door

SKU 902002 and 902010 are rated at 250lbs for up to a 36" door and 200lbs for a 36" to 40" door

SKU 902004 and 902012 are rated at 300lbs for a 36" to 40" door and 250lbs for a 42" to 46" door

SKU 902006 and 902014 are rated at 300lbs for up to a 48" door

Finishes:

• Chrome plated, highly polished
• Black Coated

• Strap side of hinge measures 2-1/2" wide by 9" long by 5/8" thick cast aluminum
• Plate side of hinge measures 4-5/8" high by 2-3/4" wide by 3/8" thick
• Hinge swings on bronze bearings
• Each hinges uses 8 each #14 flat head screws (not included)
• For doors where the frame and door are flush with each other
• The hinges are rated at 200 lbs for a pair of hinges on a door up to 36" wide

Finishes:

• Polished aluminum
• Flat Black

• Combine with a butt hinge to create the strength of a butt hinge and the look of a strap hinge
• Features decorative curls along edges
• Steel base material
• Screws are included
• Thickness of material is 5/32"

Finishes:

• Flat black

• False strap for use with butt hinges.
• Available in two lengths; 16" and 12". Actual lengths may vary by 1/4".
• The 12" is approximately 2-5/16" wide at the widest point.
• The 16" is approximately 4-3/8" wide at the widest point
• Made of rough iron with a flat black iron finish (Powder coated black)
• Matching fasteners are included.

Finishes:

• Black iron

• false straps for use with butt hinges.
• made of rough iron with a hammered flat black finish.
• strap is 3.5" wide at the widest point.
• uses a #7 flat or oval head screw (not included).

Finishes:

• flat black, hammered

• Combine with a butt hinge to create the strength of a butt hinge and the look of a strap hinge
• Overall length is 27-1/2"
• Pad end width is 1-9/16"
• Thickness is 7/32"
• Comes with decorative pyramid head screws (3/4" square head)

Finishes:

• smooth flat black

• Antique style strap hinge made for surface mounting (door and frame are flush with each other).
• Strap leaf measures 11-3/4" by 2-3/8" at widest point.
• Vertical leaf measures 4-5/16" by 1-1/8".
• Measurements are to center of hinge pin.
• Hinges are weight rated at 15 lbs. per hinge.
• Made from steel base material. Matching wood screws are included.

Finishes:

• Black Powder Coated

• Antique style shutter hinge made for surface mounting.
• Strap leaf measures 12-1/4" by 2-3/4" at widest point.
• Vertical leaf measures 5-1/4" by 1-3/8".
• Width measurements are to center of hinge pin.
• Hinges are weight rated at 15 lbs per hinge.
• Made from steel base material. Matching wood screws are included.

Finishes:

• Black powder coated

• This very high quality solid bronze strap hinge is made for use in coastal areas or anywhere a rustic old world design is desired. From our "Solid Bronze Collection".
• This product is sold in components. The components consist of 2 items; a strap which attaches to the gate surface and a pintle which attaches to the post. The pintle is available as either a "Plate Pintle" or a "Screw-in Pintle".
• Lag screws are included. The Lag Screws are made from stainless steel and coated black. Lag Screws are available in two lengths (1.5" or 2.5"). Please specify which length you prefer in the "Comment" section when you checkout.
• Two hinges will support a 150 lb. gate or door. Three hinges will support a 250 lb. gate or door.
• Bronze is an old world material that does not deteriorate in coastal or other regions. The Bronze finish, however, is a "living" finish. Please read more about this by clicking on the link.

Finishes:

• Natural Solid Bronze

• Dummy straps install on the face of any door or gate to give the look of a decorative strap hinge. They are normally used in combination with full mortise butt hinges.
• Dummy straps made of solid bronze are for use in coastal areas or anywhere a rustic old world design is desired. From our "Solid Bronze Collection".
• Matching wood screws are included.
• These beautiful dummy straps are available in 6 lengths.
• Bronze is an old world material that does not deteriorate in coastal or other regions. The Bronze finish, however, is a "living" finish. Please read more about this by clicking on the link.

Finishes:

• Solid Natural Bronze

• Solid bronze dummy strap hinge for use in coastal areas or anywhere a rustic old world design is desired. From our "Solid Bronze Collection".
• Dummy straps provide a decorative strap look to a gate or door hinged with full mortise butt hinges.
• Available in two lengths. Both sizes are made from 1/4" thick material. Both sizes are 2" wide and measure 4" at the widest part.
• Wood screws are included.
• Bronze is an old world material that does not deteriorate in coastal or other regions. The Bronze finish, however, is a "living" finish. Please read more about this by clicking on the link.

Finishes:

• Solid Natural Bronze

• Dummy strap has a unique hammered black finish
• Measures 14" long, 3-3/8" at wide end, 1-3/8" at narrow end and 7/32" thick
• This product is sold in pairs only
• Steel base material
• Matching wood screws included

Finishes:

• Hammered black finish

• False Strap for use with butt hinges
• Black square head screws are included
• 24 inches in length
• 10-1/2 inches at widest point
• made of 7/64" thick steel

Finishes:

• Black Iron

• English style dummy strap is available in two lengths; 12" and 16".
• The 12" strap measures 4.5" at its widest point.
• The 16" strap measures 6.25" at its widest point.
• Both are made from approximately 7/32" steel.
• Wood screws are included.

Finishes:

• Black Powder Coated

• Ornamental dummy strap is meant to be used with a butt type hinge.
• Strap measures 10" long by 2-1/4" at its widest point. Thickness is 3/16".
• Made of steel with rough texture to simulate wrought iron.
• Matching wood screws are included.

Finishes:

• Black Powder Coated

• Ornamental dummy strap is meant to be used with a butt type hinge.
• Strap measures 8.5" long by 2-3/8" at its widest point. Thickness is 1/4".
• Made of steel with rough texture to simulate wrought iron.
• Matching wood screws are included.

Finishes:

• Black Powder Coated

• Flat end dummy strap is used with a butt hinge to give the strap hinge appearance.
• Dummy strap is available in 4 lengths. All dummy straps are 1/4" thick and 1-1/2" in width.
• Made from steel.
• Includes wood screws for installation and round 1-3/8" clavos to cover up the wood screw heads and for additional detail.

Finishes:

• Flat Black Wrought Iron

• Dummy straps install on the face of any door, gate or shutter to give the look of decorative strap hinges.
• These dummy straps feature a black hammered or wrought iron look with an arrowhead style.
• Available in 4 lengths. They are 2" wide and 1/4" thick.
• Round decorative clavos (1-1/4" diameter) are included to cover up the attachment screws (which are included also).
• Made from steel base material.

Finishes:

• Hammered Black Iron

• Stainless steel strap hinge made for surface mounted installations.
• Hinge measures 3-1/8" tall by 5" wide.
• Made from type 304 stainless steel.
• Each hinge uses 4 each #14 pan head screws (not included but offered for purchase during checkout).

Finishes:

• Natural Stainless Steel

• Heavy duty strap hinge for gates, truck doors or anywhere a heavy duty stainless steel strap hinge is needed.
• Made for surface mounted flush installation.
• Made from 0.197" thick stainless steel.
• Horizontal strap measures 2.5" tall by 7-3/8" wide (measured from center of hinge pin).
• Vertical strap measures 4-1/8" tall by 2-1/4" wide (measured from center of hinge pin).
• Hinge pin is removable (held in place by a circlip). Hinge pin features a zerk fitting to allow lubrication.
• Each hinge uses 6 each 5/16" lag screws (not included but offered for purchase during checkout).

Finishes:

• Polished Stainless

• Beautifully polished stainless steel strap hinge, made from Type 304 stainless steel.
• Horizontal strap measures 3.5" from center of hinge pin to end of strap.
• Vertical strap measures 2-1/4" tall by 1-3/8" from center of hinge pin to edge of strap.
• Thickness is 0.135".
• Hinge is designed for flush installation (surface mounted).
• Each hinge uses 4 each #14 pan head screws (not included but offered for purchase during checkout).

Finishes:

• Polished Stainless Steel

• Decorative Tee strap for gates, large cabinets and full size doors.
• Tee strap measures 6" wide by 6" tall by 3/4" wide by 5/32" thick.
• Made from steel base material.
• Matching wood screws are included.

Finishes:

• Hammered Black

• Decorative "L" strap for gates, large cabinets and full size doors.
• Each leg of the "L" strap measures 6" by 3/4" wide by 5/32" thick.
• Made from steel base material.
• Matching wood screws are included.

Finishes:

• Hammered Black

• Decorative angled "L" strap for gates, large cabinets and full size doors.
• Each leg of the "L" strap measures 6" by 3/4" wide by 5/32" thick.
• Made from steel base material.
• Matching wood screws are included.

Finishes:

• Hammered Black

• Decorative arch strap for gates, large cabinets and full size doors.
• Strap measures 17" by 3/4" wide by 5/32" thick.
• Made from steel base material.
• Matching wood screws are included.

Finishes:

• Hammered Black

• Click on the link below to go to our main Strap Hinge section where you will find our complete selection of Strap Hinges.