Bolt, Screw, Strap & Pintle Hinges

Bolt, Screw, Strap & Pintle Hinges

  • Over 80 different bolt, screw, strap and pintle hinges are found in this section.
  • Pintle hinges have a vertical pintle which acts as the pivot point of the hinge.
  • Pintle hinges can be installed so that the gate may be lifted off of the post after installation.

Heavy Duty J-Bolt Pivot Hinge-

Heavy Duty J-Bolt Pivot Hinge-
  • This is a very heavy duty hinge specially made for heavy gates and doors.
  • This hinge will swing a full 180 degrees if installed without a stop.
  • Hinge is made up of a mounting plate (flange) and J-Bolt arm.
  • Hinge pivots on a steel ball bearing and includes a grease fitting to keep the bearing lubricated.
  • Mounts with 3/8" lag screws or bolts (not included).
  • The minimum gap between the post and edge of gate frame is 2-1/2" for SKU 783000 and 3-1/8" for SKU 783002.
  • The maximum spread between the two nuts on the threaded part is 2-3/4" for 783000 and 4-1/4" for 783002.
  • The thread size on our SKU 783000 is 5/8 x 11. The thread size on our SKU 783002 is 3/4 x 10.
  • Screw hole center to center measurement for SKU 783000 is 3-15/16".
  • Weight rating is for 2 hinges.

Finishes:

  • Black Coated

Click here for Information & Pricing

Pintle Hinge for Arched Top Gates

Pintle Hinge for Arched Top Gates
  • Hinge is made for gates with a curved or arched top.
  • Made for gates where the surface of the gate is flush with the post.
  • This is a pintle style hinge. Gate straps fit over vertical pintles that are installed on the gate post.
  • Made from steel and black coated.
  • Fasteners are included.
  • Dimensions:
    • Top Hinge is approximately 11.5" wide by 8.5" tall.
    • Each Pintle plate is approximately 5-3/8" tall by 1.5" wide, plate projection is 1-7/16".
    • Bottom Hinge is approximately 5-3/8" tall by 7-3/4" wide.
  • This hinge is sold by the set. A set includes a top hinge and a bottom hinge (as shown in the image).A set is what is needed to hang one gate.
  • IMPORTANT: These hinges are handed (left hand or right hand).
    • The hinge shown in the image above is a Right Hand set (SKU 215539).
    • To view an image of the Left Hand set (SKU 215537) click on link below.
Click here for Information & Pricing

Black Bolt & Strap Pintle Hinge

Black Bolt & Strap Pintle Hinge
  • Black Bolt & Strap Pintle Hinge
  • Available in 3 sizes
    • 12 Inch Strap
    • 18 Inch Strap
    • 24 Inch Strap
  • Sold by the pair
  • A pair includes
    • two straps
    • two pintle bolts
    • fasteners needed to install
  • A pair is normally whay you need to install one gate or door.
Click here for Information & Pricing

Pintle Type Strap Hinges with Wood Screws-

Pintle Type Strap Hinges with Wood Screws-
  • Heart style strap hinge with a pintle end
  • Pintle end fastens to wood or masonry (with masonry anchor not included)
  • Comes complete with black square head wood screws
  • This hinge can be used on a gate weighing up to 175lbs (per pair of hinges).
  • Pintle style mounting allows gate to be removed by lifting off pintle
  • With "pintle style mounting" your gate can be installed so it can swing both ways (in and out) or it can be installed so that it opens only one way (either in or out).
  • Normal installation requires two hinges per gate
  • "Hook Size" refers to the dimensions of the threaded portion.

Finishes:

  • Black Iron
Click here for Information & Pricing

Pintle Type Strap Hinges with Carriage Bolts-

Pintle Type Strap Hinges with Carriage Bolts-
  • Heart style strap hinge with a pintle end that fastens to wood or masonry (with masonry anchor, not included)
  • This strap hinge is for heavy duty use. It can be used on a gate weighing up to 250lbs (per pair of hinges). Comes complete with 3 black carriage bolts (plus nuts and washers) and a black square head wood screw
  • Pintle style mounting allows gate to be removed by lifting off pintle
  • With "pintle style mounting" your gate can be installed so it can swing both ways (in and out) or it can be installed so that it opens only one way (either in or out).
  • Normal installation requires two hinges per gate
  • "Hook Size" refers to the dimensions of the threaded portion. "Screw Size" refers to the carriage bolt dimensions.

Finishes:

  • Black Iron
Click here for Information & Pricing

Bean Style Pintle Strap Hinge

Bean Style Pintle Strap Hinge
  • Bean style strap hinge with a pintle end
  • Pintle end fastens to wood or masonry (with masonry anchor not included)
  • Comes complete with black wood screws to attach to gate side
  • This hinge can be used on a gate weighing up to 175lbs (per pair of hinges).
  • Pintle style mounting allows gate to be removed by lifting off pintle
  • With "pintle style mounting" your gate can be installed so it can swing both ways (in and out) or it can be installed so that it opens only one way (either in or out).
  • Normal installation requires two hinges per gate
  • "Hook Size" refers to the dimensions of the threaded portion.
  • Matches other "Bean" style products found on our website.

Finishes:

  • Black Iron
Click here for Information & Pricing

Bean Style Strap Hinge with Carriage Bolts

Bean Style Strap Hinge with Carriage Bolts
  • Bean style strap hinge with a pintle end that fastens to wood or masonry (with masonry anchor, not included).
  • This strap hinge is for heavy duty use. It can be used on a gate weighing up to 250lbs (per pair of hinges). Comes complete with 3 black carriage bolts (plus nuts and washers) and a black square head wood screw.
  • Pintle style mounting allows gate to be removed by lifting off pintle.
  • With "pintle style mounting" your gate can be installed so it can swing both ways (in and out) or it can be installed so that it opens only one way (either in or out).
  • Normal installation requires two hinges per gate.
  • "Hook Size" refers to the dimensions of the threaded portion. "Screw Size" refers to the carriage bolt dimensions.

Finishes:

  • Black Iron
Click here for Information & Pricing

Ornamental Heavy Duty Strap Hinge And Screw Hook

Ornamental Heavy Duty Strap Hinge And Screw Hook
    • Pintle style strap hinge.
    • Made from steel with a durable black finish.
    • Can be installed two ways
      • with both pintles facing up so the gate can be lifted off after installation.
      • with the pintles facing towards each other so the gate cannot be lifted off after installation.
    • Decorative styling.
    • Comes complete with matching lag screws.
    • Dimensions are shown below.
  • Finishes:

    • Black Coated
Click here for Information & Pricing

Ornamental Strap Hinge And Screw Hook

Ornamental Strap Hinge And Screw Hook
  • durable black finish and steel base material
  • decorative style
  • complete with lag screws

Finishes:

  • Black Coated
Click here for Information & Pricing

Screw Hook & Eye Hinge

Screw Hook & Eye Hinge
  • This hinge is made up of two parts: a "pintle" side and an "eye".
  • Made from malleable iron.
  • Hinge can be installed in masonry by using a masonry anchor.
  • SKU 504860 measures 8.5" tip-to-tip as shown in the photo to the left. The eye size and pintle diameter is 1/2". The screw is a 5/8" screw.
  • SKU 504861 measures 10.25" tip-to-tip as shown in the photo to the left. The eye size and pintle diameter is 5/8". The screw is a 3/4" screw.
  • These hinges are sold by the pair. A pair is two sets of hinges which is usually enough to hang one gate or door.
  • The weight rating listed is per pair of hinges.

Finishes:

  • Zinc Chromate plated
Click here for Information & Pricing

Screw Eye and Pintle Hinge

Screw Eye and Pintle Hinge
  • The "Screw Eye" and "Screw Pintle" for this hinge are ordered as separate components.
  • When ordering components make sure that the "pintle" sizes match. The pintle sizes available for these components are 1/2" (Small) and 5/8" (Large).
  • The weight ratings listed are for one hinge. For example, if the listed weight rating is 100 lbs. and you install 2 hinges, your 2 hinges would be rated at 200 lbs.
  • One hinge consists of one "Screw Eye" and one "Screw Pintle". You would normally order 2 screw eyes and 2 screw pintles to hang one gate or door.

PLEASE NOTE: the sizes listed as the "Pintle Diameter" (for example 3/4" Pintle) are nominal dimensions, meaning they do not measure exactly that dimension. Use our "nominal dimension" to match up our Straps with our Bolts, etc. when you are ordering our products. If you order one of our products to match a pintle diameter of something that you already own, you do so at your own risk.

Finishes:

  • Zinc Chromate
Click here for Information & Pricing

Heavy Duty Adjustable Band and Pintle Strap Hinge

Heavy Duty Adjustable Band and Pintle Strap Hinge
  • Heavy duty pintle type strap hinge for gates and doors.
  • Door or gate can be lifted-off after installation.
  • This hinge is adjustable horizontally. There is a 2" range of adjustment after installation.
  • Pintle plate measurements:
    • Pintle plate is 6-1/2" tall by 2-1/4" wide by 3/16" thick.
    • Pintle is 3/4" diameter by 1-1/2" tall.
    • Projection is approximately 2-1/4".
  • Straps are made from 3/16" thick heavy duty steel and have welded diagonal plates at the post end for additional strength. Straps are 2-3/16" tall. Projection at post end is approximately 2".
  • Available in 3 strap lengths
    • 14 Inch Strap Model (SKU 215514). Actual strap length is 13".
    • 18 Inch Strap Model (SKU 215516). Actual strap length is 17".
    • 24 Inch Strap Model (SKU 215518). Actual strap length is 22-1/2"
  • Listed weight ratings are per pair of hinges.
  • Fasteners are included. (Black matching wood screws and one black carriage bolt per strap) .
  • This hinge is sold by the pair. There are two hinges in a pair.
Click here for Information & Pricing

Strap for Pintle System of Gate Hinges

Strap for Pintle System of Gate Hinges
  • These straps are part of our pintle system of gate hinges.
  • This product will work with the Upright Pintle, Bolt Pintle or Screw Pintle.
  • When ordering the other part of this hinge make sure that the pintle sizes match. For example if you order a strap with a 5/8" pintle and bolt pintle to go with it your bolt pintle must have a 5/8" pintle also.
  • Made from steel base material.
  • Straps install with either lag screws or carriage bolts (not included).
  • The weight ratings listed are for one hinge. For example if the listed weight rating is 100 lbs and you use two hinges then your two hinges would be rated at 200 lbs.

PLEASE NOTE: the sizes listed as the "Pintle Diameter" (for example 3/4" Pintle) are nominal dimensions, meaning they do not measure exactly that dimension. Use our "nominal dimension" to match up our Straps with our Bolts, etc. when you are ordering our products. If you order one of our products to match a pintle diameter of something that you already own, you do so at your own risk.

Finishes:

  • Zinc Chromate
Click here for Information & Pricing

Bolt Pintle for Pintle System of Gate Hinges

Bolt Pintle for Pintle System of Gate Hinges
  • These bolt pintles are part of our pintle system of gate hinges.
  • This product will work with the Strap or Screw eye.
  • Maximum post sizes(maximum distance between the washers) for the "Bolt" are as follows; SKU 504820 is 4-5/8", SKU 504821 is 6-1/2", 504822 is 10-1/4", 504823 is 7-7/8", 504824 is 10" and 504825 is 9-7/8".
  • When ordering the other part of this hinge make sure that the pintle sizes match. For example if you order a strap with a 5/8" pintle and bolt pintle to go with it your bolt pintle must have a 5/8" pintle also.
  • Made from steel base material.
  • The weight ratings listed are for one hinge. For example if the listed weight rating is 100 lbs and you use two hinges then your two hinges would be rated at 200 lbs.

PLEASE NOTE: the sizes listed as the "Pintle Diameter" (for example 3/4" Pintle) are nominal dimensions, meaning they do not measure exactly that dimension. Use our "nominal dimension" to match up our Straps with our Bolts, etc. when you are ordering our products. If you order one of our products to match a pintle diameter of something that you already own, you do so at your own risk.

Finishes:

  • Zinc Chromate
Click here for Information & Pricing

Screw Pintle for Pintle System of Gate Hinges

Screw Pintle for Pintle System of Gate Hinges
  • The Screw Pintle is part of our pintle system of gate hinges.
  • This product will work with a strap or screw eye (sold separately).
  • When ordering the other part of this hinge make sure that the pintle sizes match. For example if you order an screw pintle with a 5/8" pintle your strap must have a 5/8" pintle also.
  • Made from steel base material.
  • The weight ratings listed are for one hinge. For example if the listed weight rating is 100 lbs and you use two hinges then your two hinges would be rated at 200 lbs.

PLEASE NOTE: the sizes listed as the "Pintle Diameter" (for example 3/4" Pintle) are nominal dimensions, meaning they do not measure exactly that dimension. Use our "nominal dimension" to match up our Straps with our Bolts, etc. when you are ordering our products. If you order one of our products to match a pintle diameter of something that you already own, you do so at your own risk.

Finishes:

  • Zinc Chromate
Click here for Information & Pricing

Upright Pintle for Pintle System of Gate Hinges

Upright Pintle for Pintle System of Gate Hinges
  • The Upright Pintle is part of our pintle system of gate hinges.
  • This product will work with a strap or screw eye.
  • When ordering the other part of this hinge make sure that the pintle sizes match. For example if you order an upright pintle with a 5/8" pintle your bolt must have a 5/8" pintle.
  • Made from steel base material.
  • Both the 1/2" and 5/8" Upright pintle use 2 each 3/8" lag screws per upright (not included).
  • The weight ratings listed are for one hinge. For example if the listed weight rating is 100 lbs and you use two hinges then your two hinges would be rated at 200 lbs.

PLEASE NOTE: the sizes listed as the "Pintle Diameter" (for example 3/4" Pintle) are nominal dimensions, meaning they do not measure exactly that dimension. Use our "nominal dimension" to match up our Straps with our Bolts, etc. when you are ordering our products. If you order one of our products to match a pintle diameter of something that you already own, you do so at your own risk.

Finishes:

  • Zinc Chromate
Click here for Information & Pricing

Screw Eye for Pintle System of Gate Hinges

Screw Eye for Pintle System of Gate Hinges
  • These Screw Eyes are part of our pintle system of gate hinges.
  • This product will work with a Screw Pintle, an Upright Pintle, or a Bolt Pintle.
  • SKU 504862 fits a 1/2" Pintle, is 4-5/8" long overall and has a 1/2" diameter screw thread.
  • SKU 504863 fits a 5/8" pintle, is 5-5/8" long overall and has a 5/8" diameter screw thread.
  • Made from steel base material.
  • When ordering the other part of this hinge make sure that the pintle sizes match.

PLEASE NOTE: the sizes listed as the "Pintle Diameter" (for example 3/4" Pintle) are nominal dimensions, meaning they do not measure exactly that dimension. Use our "nominal dimension" to match up our Straps with our Bolts, etc. when you are ordering our products. If you order one of our products to match a pintle diameter of something that you already own, you do so at your own risk.

Finishes:

  • Zinc Chromate
Click here for Information & Pricing

Upright Pintle & Strap Hinge

Upright Pintle & Strap Hinge
  • Upright pintle mounts to gate post and strap mounts to gate.
  • The "Upright" and the "Strap" are ordered as separate components.
  • When ordering components make sure that the pintle sizes match. The pintle sizes available for these components are 1/2" and 5/8".
  • The weight ratings listed are for one hinge. For example if the listed weight rating is 100 lbs. and you install 2 hinges, your 2 hinges would be rated for a 200lb gate.
  • Components install with lag screws or carriage bolts (not included).
  • The design of this product creates a small gap between the post and gate (approximately 3/8") after installation.

PLEASE NOTE: the sizes listed as the "Pintle Diameter" (for example 3/4" Pintle) are nominal dimensions, meaning they do not measure exactly that dimension. Use our "nominal dimension" to match up our Straps with our Bolts, etc. when you are ordering our products. If you order one of our products to match a pintle diameter of something that you already own, you do so at your own risk.

Finishes:

  • Zinc Chromate
Click here for Information & Pricing

Upright Pintle and Screw Eye

Upright Pintle and Screw Eye
  • Upright pintle mounts to gate post and screw eye mounts to gate. Or it can be mounted upside down with the screw eye going into the post and the upright pintle mounting to the gate.
  • The "Upright" and the "Screw Eye" are ordered as separate components.
  • When ordering components make sure that the pintle sizes match. The pintle sizes available for these components are 1/2" and 5/8".
  • The weight ratings listed are for one hinge. For example if the listed weight rating is 100 lbs. and you install 2 hinges, your 2 hinges would be rated for a 200lb gate.
  • Upright Pintle installs with lag screws or carriage bolts (not included).
  • Made from steel base material.

PLEASE NOTE: the sizes listed as the "Pintle Diameter" (for example 3/4" Pintle) are nominal dimensions, meaning they do not measure exactly that dimension. Use our "nominal dimension" to match up our Straps with our Bolts, etc. when you are ordering our products. If you order one of our products to match a pintle diameter of something that you already own, you do so at your own risk.

Finishes:

  • Zinc Chromate
Click here for Information & Pricing

Bolt & Strap Hinge

Bolt & Strap Hinge
  • The "bolt" and "strap" for this hinge are ordered as separate components.
  • When ordering components make sure that the "pintle" sizes match. The pintle sizes available for these components are 1/2", 5/8", 3/4" and 7/8".
  • Maximum post sizes(maximum distance between the washers) for the "Bolt" are as follows; SKU 504820 is 4-5/8", SKU 504821 is 6-1/2", 504822 is 10-1/4", 504823 is 7-7/8", 504824 is 10" and 504825 is 9-7/8".
  • The weight ratings listed are for one hinge. For example, if the listed weight rating is 100 lbs. and you install 2 hinges, your 2 hinges would be rated at 200 lbs.
  • One hinge consists of one "strap" and one "bolt". You would normally order 2 straps and 2 bolts to hang one gate or door.
  • The "straps" are normally installed using carriage bolts (not included).
  • Two washers and two nuts are included with each "bolt" ordered.

PLEASE NOTE: the sizes listed as the "Pintle Diameter" (for example 3/4" Pintle) are nominal dimensions, meaning they do not measure exactly that dimension. Use our "nominal dimension" to match up our Straps with our Bolts, etc. when you are ordering our products. If you order one of our products to match a pintle diameter of something that you already own, you do so at your own risk.

Finishes:

  • Zinc Chromate
Click here for Information & Pricing

Screw Hook And Strap Hinge

Screw Hook And Strap Hinge
  • The Screw Hook and Strap Hinges found in this section are only available in smaller sizes and are sold by the pair.
  • A pair is two complete hinges. A pair is what is normally required to hang one gate or door.
  • For surface mounted doors.
  • Heavy duty steel strap pivots on post of a malleable iron screw hook.
  • Uses 5/16" carriage bolts for the strap (not included)
  • For a selection of larger Screw Hook and Strap Hinges click on the link below.

Finishes:

  • Zinc Plate
Click here for Information & Pricing

Screw & Strap Hinge Components

Screw & Strap Hinge Components
  • The "screw" and "strap" for this hinge are ordered as separate components.
  • When ordering components make sure that the "pintle" sizes match. The pintle sizes available for these components are 1/2", 5/8", 3/4" and 7/8".
  • The weight ratings listed are for one hinge. For example, if the listed weight rating is 100 lbs. and you install 2 hinges, your 2 hinges would be rated at 200 lbs.
  • One hinge consists of one "strap" and one "screw". You would normally order 2 straps and 2 bolts to hang one gate or door.
  • The "straps" are normally installed using carriage bolts (not included).
  • Steel base material

PLEASE NOTE: the sizes listed as the "Pintle Diameter" (for example 3/4" Pintle) are nominal dimensions, meaning they do not measure exactly that dimension. Use our "nominal dimension" to match up our Straps with our Bolts, etc. when you are ordering our products. If you order one of our products to match a pintle diameter of something that you already own, you do so at your own risk.

Finishes:

  • Zinc Chromate
Click here for Information & Pricing

Pipe Mounted Pintle Hinge

Pipe Mounted Pintle Hinge
  • The pipe hinge is part of our pintle system of gate hinges.
  • This product will work with a screw pintle, bolt pintle or upright pintle. All are sold separately.
  • When ordering the other part of this hinge make sure that the pintle sizes match. For example if you order a Pipe Mounted Pintle Hinge with a 5/8" pintle make sure the other component has a 5/8" pintle size also.
  • Made from steel base material.
  • There are two models; one model fits a 1-5/8" diameter pipe and the other model fits a 2" diameter pipe (dimensions listed are actual outside diameter measurements of pipe or tubing).
  • The weight ratings listed are for one hinge. For example, if the listed weight rating is 70lbs for one hinge and you use two hinges then your combined hinge installation would be rated at 140lbs.

PLEASE NOTE: the sizes listed as the "Pintle Diameter" (for example 3/4" Pintle) are nominal dimensions, meaning they do not measure exactly that dimension. Use our "nominal dimension" to match up our Straps with our Bolts, etc. when you are ordering our products. If you order one of our products to match a pintle diameter of something that you already own, you do so at your own risk.

Finishes:

  • Zinc Chromate
Click here for Information & Pricing

Pintle Hinge for Livestock Gates, Medium

Pintle Hinge for Livestock Gates, Medium
  • Medium duty livestock gate hinge for use on 1-3/4"" (outside diameter) round tube gates.
  • Pintle side of hinge uses a "lag screw" thread to attach to the gate post with a 6.5" long bolt (11/16" diameter). Threaded portion of lag screw pintle is 4.5" so the minimum post width should be at least 4.5". Pintle size is 5/8" x 2".
  • Carriage bolts, nuts, and washers are included to attach brackets to round gate post.
  • These hinges are sold by the pair. A pair is usually what is required to hang one gate.
  • PLEASE NOTE: the green tubing and wooden post shown in the photo are for illustrative purposes and are not included with the hinge.

Finishes:

  • Zinc Chromate Plated
Click here for Information & Pricing

Pintle Hinge for Livestock Gates, Large

Pintle Hinge for Livestock Gates, Large
  • Heavy duty livestock gate hinge for use on 2" (outside diameter) round tube gates.
  • Pintle side of hinge "through-bolts" to the gate post with a 12.5" long bolt (3/4" diameter). Maximum post size is 9.5" in width. Pintle size is 7/8" x 2".
  • Carriage bolts, nuts, and washers are included.
  • These hinges are sold by the pair. A pair is usually what is required to hang one gate.
  • PLEASE NOTE: the green tubing and wooden post shown in the photo are for illustrative purposes and are not included with the hinge.

Finishes:

  • Zinc Chromate Plated
Click here for Information & Pricing
accredited business BBB
Sign up for email updates from HardwareSource and get 5% OFF your next order!
Email:

see what customers are saying

Over 10,000 Reviews
5 Star Average

High quality, received them promptly without special shipping. Great quality, saved over 100.00 over Home Depot. ... (Read review)
Very reliable vendor - would do business with again. Very prompt shipping and the order was processed flawlessly! ...
Guaranteed: All Valid Reviews Posted
StatisticsReview of HardwareSource.com

Related Products