• Folding shelf support allows shelf to fold down when not in use.
• Shelf will lock in place when in the horizontal (90 degree) position.
• There are also two other locking positions: 80 degrees and 70 degrees.
• Shelf can fold flat against the wall when not in use (0 degrees).
• Shelf releases from the locked position by pressing on a lever which is positioned inside and at the end of the horizontal piece (lift up slightly on the shelf and press the release lever).
• Two of these folding shelf supports will support up to a 750 lb load. when properly attached to a vertical surface. Proper attachment depends on the type of vertical surface (wood studs, masonary, etc). Proper attachment may require the use of fastener anchors, consult a fastener expert if necessary.
• Available in two sizes: a smallmodeland a large model.
  • Small model measurements;
    • The horizontal piece measures 11-3/4" long by 1-3/16" wide by 7/8" thick.
    • The vertical piece measures 7-7/8" tall by 3/4" wide by 7/8" thick.
    • It uses #10 pan or round head screws (8 per folding shelf support).
    • Screws are not included, but are offered for purchase during checkout.
    • After installation and when the shelf is folded in the down position, the gap between the bottom of the shelf and the wall it is attached to will be approximately 1".
  • Large model measurements;
    • The horizontal piece measures 15-3/4" long by 1-7/16" wide by 1-1/16" thick.
    • The vertical piece measures 10-11/16" tall by 15/16" wide by 1-1/16" thick.
    • It uses #12 pan or round head screws (8 per folding shelf support).
    • Screws are not included, but are offered for purchase during checkout.
    • After installation and when the shelf is folded in the down position, the gap between the bottom of the shelf and the wall it is attached to will be approximately 1-1/4".
• Made from steel. The latching lever and mechanism is zinc plated. Available in a choice of two finishes;
  • White Powder Coated (image shows this finish)
  • Zinc Chromate (a shiny chrome-like finish)
• This product is sold by the "each". You would normally order 2 or more for each shelf you are installing (depending on the shelf length).

• This hinged shelf support "locks in place" when in the horizontal position. Lifting shelf vertically allows shelf to fold down against wall when not in use.
• Horizontal piece measures 11" and vertical piece measures 5"
• There are 2 mounting holes on vertical piece that are 2" on center
• Steel base material
• Bracket spacing should not exceed 32"
• When the shelf is in the fold-down position the gap between the wall and the bottom of the shelf is 2-1/2"
• Screws are included
• Weight rating is for a pair of supports when spacing does not exceed 32"
• Product is sold by the pair. A pair is two shelf supports

Finishes:

• White Powder Coat

• Folding bench seat hinge is extra heavy duty.
• A pair of these bench seat hinges will hold up to 1100 lbs.
• May also be used as a folding shelf support.
• When not in use the seat or shelf folds up against the wall. In the up position the seat or shelf is held in place by gravity. If a more secure hold fast is needed, it will be necessary to add something such as a chain or other more positive holding device.
• Wall mounting plate measures 8" tall by approximately 3.5". Plate is slightly over 1/4" thick.
• Fold down arm projects out from wall 15".
• Fold down arm is made from U-shaped steel and measures 1.5" x 1.5"
• Wall mount uses 4 each 3/8" diameter fasteners (not included). Arm uses 4 each 1/4" diameter fasteners (not included).
• Because of the large load capacity of this device, it is important to use a proper method of attachment to your wall. Different wall types will use different attachment methods. Be sure to seek advice from a professional if you are not knowledgable in this area.
• This product is sold by the "EACH". You will normally need to order 2 each for each bench seat or shelf you are hanging.

Finishes:

• Heavy Zinc Chromate Plating

• Table leaf hinge allows table leaf to fold down into vertical position or to lock into horizontal position.
• Table leaf hinge is approximately 16" in length when in the "up" position. Click on link below for more specific dimensions.
• Features a release button which is located near the end of the table leaf. Release button releases the lock on the hinge and allows table leaf to be lowered into vertical position.
• For table leaves up to approximately 14" in front to back depth.
• Manufacturer recommends a maximum load capacity of 66lbs per pair.
• Photo shows table leaf hinge in the "down" or vertical position.
• Made from steel base material.
• Uses 7 each #8 pan head screws per hinge, not included but offered for purchase during checkout.
• These hinges are sold by the each. You would normally order 2 each hinges per table leaf.

Finishes:

• Yellow zinc plated

• This product fastens a shelf to a wall and allows the shelf to hinge down flat against the wall.
• Extra heavy duty construction
• Size of each bracket is 23-3/4" by 21"
• Maximum load is 200lbs per pair of brackets
• Bracket spacing should not exceed 32"
• When the shelf is in the down position there will be a gap of 1" between the underside of the shelf and the surface of the wall.
• This piece of hardware has a very easy-to-use release mechanism. To fold the shelf or table back down against the wall, lift the front edge of the shelf about 1" and push in on the diagonal supports slightly. The table will then fold down to its vertical position.
• Screws are included
• These brackets are sold by the pair. One pair is needed per shelf.

Finishes:

• Zinc Chromate Plated

• Product fastens a shelf to a wall and allows the shelf to hinge down flat against the wall.
• Product is sold by the pair, a pair is two shelf supports.
• Bracket spacing should not exceed 32".
• Made from steel base material.
• Weight rating is for a pair of supports when spacing does not exceed 32".
• The maximum shelf width for each size support is listed below.
• The "Hinge Gap" dimension listed below is the distance from the wall to the underside of the shelf after installation and when the shelf is in the "folded down" position.
• Screws are not included.

Finishes:

• White enameled

• Hinged shelf support allows shelf to fold down when not in use.
• Shelf will lock in place when in the horizontal position. Shelf releases by pressing a lever on the horizontal piece.
• Made from type 304 stainless steel (1/16" thick material)
• Vertical arm measures 6.5". Horizontal arm measures 12". Width of both arms is 7/8".
• After installation and when the shelf is in the folded down position, the gap between the bottom of the shelf and the wall it is attached to will be approximately 1-1/8".
• The manufacturer of this item does not provide any weight ratings for this product but it should be comparable to other similiar products that we stock.
• Uses 12 each #10 pan head screws, not included but offered for purchase during checkout.
• This product is sold by the pair. A pair is two shelf supports.

Finishes:

• Polished Stainless Steel

• This hinge is for use as with a drop panel on a wall unit. Two legs will support the drop panel for use as a table or work surface.
• The hinge allows a 1" x 2-1/2" leg to swing 270 degrees from vertical so that it can be folded into the wall with the drop panel. Legs are concealed when drop panel is raised.
• Works only with a 3/4" thick table top
• Hinge shown in photo is in the "folded up" position.
• Steel base material, uses 6 each #6 flat head screws per hinge (not included but offered for purchase during checkout)

Finishes:

• Zinc Chromate

• Allows table leg to fold up under table when not in use
• Spring activated trigger release provides positive locking in both open and closed position
• Accomodates 1-1/2" square leg without cutting or shaping
• Steel base material
• Each hinge uses 6 each #6 round head screws (not included but offered for purchase during checkout). Order our SKU 286252 for a matching finish.

Finishes:

• Bronze plated

• Allows table leg to fold up under table when not in use
• This table leg hinge works with any size table leg
• Spring activated trigger release provides positive locking in both open and closed position
• Steel base material
• Screws are not included. For matching screws order our SKU 286252 (order 11 per hinge). Screws are offered for purchase during checkout.
• Size is approximately 2-1/8" tall by 2-1/4" wide by 3" thick

Finishes:

• Bronze plated

• This hinge works well for hinging a bench seat
• It is available with springs (as shown in photo) or without springs
• SKU 796030 (with springs) will counter balance a seat or lid weighing between 17 and 26lbs (keeps the seat from slamming shut and makes it easier to open)
• SKU 796033 (without springs) works as a hinge without the counter balancing feature for lighter seats. Keep in mind that this model will not keep the seat from slamming shut
• Both models allow the seat to open to 95 degrees
• With both models the seat will move forward about 4" as it opens the full 95 degrees
• Both models are sold by the pair. A pair includes a left hand hinge and a right hand hinge
• Requires 8 each #12 Pan Head wood screws per pair (not included but offered for purchase during checkout)
• This hinge is not recommended for toy boxes as it could be a danger to small fingers

Finishes:

• Yellow chromated

• Hinged brace for folding table legs
• One end attaches to underside of table and the other end attaches to table leg
• Positive locking feature
• Steel construction
• Sold by the pair, a pair includes two braces (one right hand, one left hand)
• For a table with 4 legs order 2 pairs
• Screws are included
• Size is 13-1/2" by 5/8"

Finishes:

• Zinc Chromate Plated

• Length is 9-1/2" in the fully open position
• For supporting box lids or table legs
• Steel base material
• Wood screws are included
• They are sold by the pair which is two supports
• Non-handed

Finishes:

• Brass plated

• Extra heavy brace is ideal for use on tables with folding legs
• Designed with a positive, easily operated locking feature
• Legs lie flat against table when legs are folded
• Steel construction
• Sold by the pair, a pair includes two braces (one right hand, one left hand)
• Screws are included

• Size is 16-5/8" by 1-1/4"

  
  Finishes:

• Zinc Chromate Plated

• For drop leaf tables and folding shelves.
• This product works in conjunction with a hinge (purchased separately) to hold the table leaf in a horizontal position.
• Please click on the link below for mounting dimensions.
• The minimum width of the part of the shelf that folds down is 8".
• Spring tension holds brace open.
• Made from stamped steel construction.
• Overall length is 10-1/2".
• Two supports are needed per drop leaf (unless the drop leaf is very short).
• Screws are included.

Finishes:

• Black

• This hinge is used to raise and support a table leaf in the horizontal position without any other hardware except the hinge itself.
• This hinge is in use in many restaurants, by flipping up a rounded table leaf, a square or rectangular table can be turned into a round table. Hinge can also be used on square or other shaped leaves. Also known as a folding leaf hinge.
• The leaf will fold back 180 degrees under the table.
• Heavy duty built-in springs hold up the table leaf
• Strong heavy gauge steel
• Approximately 8" long by 5"
• We recommend using 10 each #8 flat head screws per hinge (not included). Flat head steel screws are offered for purchase during checkout.
• Order 2 hinges per table leaf
• Click on link below to see install instructions.
• Use caution when handling this hinge as the spring is very strong and can injure fingers.
• PLEASE NOTE: If you purchase 50 or more of this hinge you will receive a 25% discount on the price.

Finishes:

• Zinc Plated

• This hinged tilt-lift table support is used wherever you need to lift a horizontal surface to a certain angle and hold it in place
• It is used on beds, sofas and drafting tables
• Lift to the desired angle and it locks in place. Lift again to release and it folds back down
• It features 10 positive locking positions
• Maximum operating arc is 112 degrees
• It is sold in pairs (a pair is two devices)
• Approximate length is 8.5"
• A hinge must be used at the pivot point (not included). We recommend two butt hinges or a piano hinge.
• Steel base material
• Screws are not included but are offered for purchase during checkout. A pair of supports uses 4 each #8 pan heads screws and 4 each #10 pan head screws.

Finishes:

• Zinc Chromate

• Pantograph type mechanism which lifts a shelf holding an item such as a blender, slicer, mixer or other appliance from inside a desk or cabinet. Places item at working height.
• Two powerful springs aid the shelf as it is raised or lowered
• Automatically locks in the raised position
• Release the locks to lower the shelf
• Made from .125" steel
• Measures 28" in the fully extended raised position (as shown in the photo)
• Maximum recommended load is 44lbs
• Maximum usable height inside the cabinet (lowered position) is 16-1/2"
• Minimum front to back cabinet depth is 19"
• Minimum interiorcabinetheight needed is 19"
• Maximum shelf depth is 16"
• There is no maximum on the shelf width
• This item is sold by the pair which it what is needed to hang one shelf.
• Uses 28 each #6 Pan head screws for installation (not included but offered for purchase during checkout)

Finishes:

• White Epoxy Laquer

• Hinge is used in RV's, Mobile Homes, etc. to extend the surface of a table
• Hinge mounts on bottom surface of table and leaf and allows the leaf to fold back on top of the table
• Hinge is self-supporting, no other hardware is required
• Hinge is surface mounted but a mortise cut is required for hinging mechanism
• Steel base material
• Hinge is not handed
• Uses #4 flat head screws (not included but offered for purchase during checkout)
• Each leaf measures approximately 1-5/8" by 3/4"
• The gap between the top and bottom plate when the table is in the closed position (as shown in the photo) is 1-5/8".

Finishes:

• Brass plated

• made in England
• 1/2" length of joint
• 3" width open
• solid brass base material
• #6 x 3/4" flat head screws included

Finishes:

• Sanded Brass

• Mounts on the edge of the table and leaf
• Mortises into the edge of the table with a 3/8 straight router bit
• Allows table leaf to flip over and support itself
• Solid brass with steel pins
• Overall width is 1-1/4"
• #6 x 5/8" flat head screws included
• Order 1 pair of hinges per table leaf

Finishes:

• Polished Brass

• for heavy cabinet work, folding shelves and table drop leaves
• hinge is a surface mounted hinge (may be partially mortised into the surface)
• fast spun pins
• hole patterns and number may vary from picture depending on size of hinge
• steel base material
• maximum door weight for 1-1/2" hinge is30 lbs per pair, the 2" hinge is 35 lbs per pair.
• wood screws are included

Finishes:

• Zinc Plated

• Hinge measures 2-3/4" in the open position.
• Hinge measures 1-1/2" along the knuckle.
• Made from Type 304 stainless steel.
• Uses #8 flat head screws (not included). Stainless steel screws are offered for purchase during checkout.

Finishes:

• Polished