Lift-off Hinges - Loose Joint Hinges

Lift-off Hinges - Loose Joint Hinges

  • Lift-off hinges allow the door to be easily removed from a piece of furniture or a box after the hinge has been installed.
  • There are over 50 different hinges in this section.
  • Made from stainless steel, brass and steel.

Lift-Off Hinge, Solid Brass with Bent Leaf

Lift-Off Hinge, Solid Brass with Bent Leaf
  • Beautifully finished solid brass lift off hinge.
  • Available in two finishes: Polished brass and Satin Nickel.
  • Hinge will "lift off" of the cabinet after installation.
  • Hinge dimensions (this is a metric designed hinge, these dimension are approximate, may vary by 1/32")
    • Height is 2"
    • Width is 3/4"
    • Bent leaf is 1/2"
    • Hinge thickness is 5/64"
    • Made to fit 3/4" or 13/16" thick door
  • Each hinge uses6 each #6 flat head wood screws. Screws are not included but are offered for purchase during checkout.
  • This hinge works well for installing an overlay door, minimum side panel thickness needed is 11/16".
  • If installedon an overlay door and such that the hinge pin is aligned just outside of the outside surface of the side panel, the door will open 270 degrees (and lay flat along side the side panel when in the fully open position).
  • Hinge is sold by the EACH. You would normally order 2 (each) hinges to hang one door.
  • Hinge shown in above image is the "Right Hand" version of this hinge.
  • This hinge is handed. Please consult the handing comparison before ordering. The handing comparison can be found by clicking on the link below.
Click here for Information & Pricing

Stainless Steel Take-Apart Hinge

Stainless Steel Take-Apart Hinge
  • Unique take-apart or lift-off hinge
  • Take-apart or lift-off hinges allow the door or lid to be removed without having to remove the fasteners
  • Made from investment cast 316 stainless steel
  • Features tab on hinge barrel which keeps the door or lid from lifting off unless the door is in the fully open position
  • Hinge can be used on a box lid or door (see important door usage information below)
  • Hinge is meant to be used as a "surface mounted" hinge
  • Hinge is approximately 1.5" tall and 3.5" wide when measured with the hinge leafs open
  • Hinge is sold by the each. You will normally order 2 hinges per door or lid.
  • Each hinge uses 4 each #10 flat head screws, not included but offered for purchase during checkout.

Information regard use of this hinge on a door

  • This hinge is only available in one model, a left hand hinge
  • If used as a door hinge, it can only be used on a door which is hinged on the left side of the cabinet.
  • If you are standing in front of the cabinet door, the door will be hinged on the left side.
  • It will not work on a door that is hinged on the right side.

Click here for Information & Pricing

Solid Brass Lift-Off Hinges

Solid Brass Lift-Off Hinges
  • Solid Brass "Lift-off" or "Loose Joint" hinges.
  • Allows opened door to be lifted off without removing the hinges.
  • Available in Left Hand or Right Hand models.
  • All hinges are 1/16" in thickness.
  • Screws are not included. All hinges use #6 flat head screws. Screws are offered for purchase during checkout.
  • 1-1/2" hinge uses 8 screws per pair
  • 2" hinge uses 12 screws per pair
  • 2-3/4" hinge uses 16 screws per pair

Finishes:

  • Polished Brass
  • Polished Chrome
Click here for Information & Pricing

1-3/4" Economy Lift Off Hinge

1-3/4
  • Our lowest priced lift-off hinge.
  • Hinges feature a loose joint so that door may be easily removed after installation.
  • Height is 1-3/4", width is 1-9/16".
  • Hinge is made from steel and brass plated.
  • Wood screws are included.
  • This hinge is only availablein handshown (left hand door while facing cabinet.) See link below for view of separated hinge.
  • Sold by the pair. A pair is normally what you need to hang one door.

    Please Note: This hinge is currently back ordered with the manufacture. We expect to have them back in stock by the end of October.
Click here for Information & Pricing

Drive-In Hinges

Drive-In Hinges
  • Drive in hinge is mounted by driving into pre-drilled holes.
  • Doors can be lifted off with ease.
  • Features a finial tipped barrel.
  • SKU #286-263 is 4-3/8" long by 11/32" diameter barrel.
  • Ribbed attachment pins are 7/32" diameter by 11/15" long.
  • Made from steel base material.
  • No screws are needed.

Finishes:

  • Bronze Plated

Click here for Information & Pricing

1-5/8" Stainless Steel Lift off Hinge

1-5/8
  • Hinges feature a loose joint so that door may be easily removed after installation
  • Hinges are available in a "left hand" or a "right hand" model
  • Hinge shown in photo is a "left hand" hinge
  • Stainless steel base material (type 304 stainless)
  • Hinges are metric so the inch dimensions listed below are approximate. Click on link below for exact metric dimensions.
  • Uses #4 flat head screws (not included but offered for purchase during checkout). Each hinge uses 4 screws.
  • Hinges are sold by "Each". Order 2 each per door.

Finishes:

  • Stainless Steel
Click here for Information & Pricing

Stainless Steel Lift off Hinges

Stainless Steel Lift off Hinges
  • Hinges feature a loose joint so that door may be easily removed after installation
  • Hinges are available in a "left hand" or a "right hand" model
  • Hinge shown in photo is a "left hand" hinge
  • Stainless steel base material (type 304 stainless)
  • Hinges are metric so the inch dimensions listed below are approximate. Click on link below for exact metric dimensions.
  • Uses #4 flat head screws (not included but offered for purchase during checkout). Each hinge uses 6 screws.
  • Hinges are sold by "Each". Order 2 each per door.

Finishes:

  • Stainless Steel
Click here for Information & Pricing

Hatch Hinge, Lift Off, Stainless Steel

Hatch Hinge, Lift Off, Stainless Steel
  • Made for boat hatches and other hatch covers.
  • Hinge is made for hatch covers that are flush with what they are hinged to.
  • Hinge may be taken apart by removing clevis pin.
  • Clevis pin is secured by a stainless ring.
  • Made from polished stainless steel (Type 316 Stainless Steel).
  • Uses #10 flat head stainless steel screws (not included but offered for purchase during checkout).
  • Hinge is sold by the each. You would normally order two hinges per hatch.
  • Click on link for hinge dimensions.
  • PLEASE NOTE: this hinge is designed with a fairly loose fit so that it is easy to remove the clevis pin.
Click here for Information & Pricing

Large Lift Off Hinge

Large Lift Off Hinge
  • Hinge measures 4-1/2" high by 4" wide
  • Loose joint hinge, opened door may be lifted off after installation
  • Comes in either a right hand or left hand model
  • Steel base material, comes complete with matching #12 wood screws
  • Hinge thickness is .139". Hinge Pin diameter is .308".

Finishes:

  • Satin Chrome
  • Oil Rubbed Bronze
  • Prime Coated
Click here for Information & Pricing

Large Lift-Off Hinges, Stainless Steel

Large Lift-Off Hinges, Stainless Steel
  • Loose joint hinge, opened door may be lifted off after installation.
  • Available in either a "Left Hand" or a "Right Hand" model.
  • Made from stainless steel (Type 304) with a satin stainless steel finish.
  • Available in a 4 x 4 inch model or a 4.5 x 4.5 inch model.
  • Hinge thickness is 0.14".
  • Hinge pin is 11/32" in diameter.
  • Stainless steel wood screws are included.
Click here for Information & Pricing

Stainless Steel Flag Lift-Off Hinges

Stainless Steel Flag Lift-Off Hinges
  • No mortise style hinge. Hinge installs as a normal full mortise butt hinge but no mortising is required.
  • Leaves only a 1/8" gap after installation.
  • Top leaf rides on a ball bearing located on the top of the hinge pin.
  • Hinge is not handed, may be used on left or right opening doors.
  • Hinge shown in photo is shown in the "door open" position.
  • Hinge is a lift off hinge, door may be lifted off after hinge is installed without removing any screws.
  • Made from solid type 304 stainless steel.
  • Available in two sizes, a 4" high hinge and a 5" high hinge.
  • The 4" hinge leaf is 1-5/8" wide not including the hinge barrel. The hinge barrel diameter is 5/8".
  • The 5" hinge leaf is 1-3/8" wide not including the hinge barrel. The hinge barrel diameter is 3/4".
  • Weight ratings listed below are for a pair of hinges.
  • Stainless steel flat head screws are included.

Finishes:

  • Satin Stainless Steel
Click here for Information & Pricing

Take-Apart Hinge, Steel

Take-Apart Hinge, Steel
  • Hinge lifts apart so lid or door may be easily removed.
  • Steel base material.
  • Joint length is 1-1/4".
  • Open width is 1-1/8".
  • Screw hole spacing is 3/4" both ways.
  • Uses #4 pan head screws (not included but offered for purchase during checkout). Uses 4 screws per hinge.

Finishes:

  • Nickel Plated
Click here for Information & Pricing

Steel Take-Apart Hinge

Steel Take-Apart Hinge
  • Steel base material.
  • Hinge lifts apart so lid or door may be easily removed.
  • Joint length is 1-5/16".
  • Open width is 1-7/8".
  • Used on cabinet or case where a removable cover is desired uses
  • Uses #6 pan head screws (not included included but offered for purchase during checkout).Uses 4 screws per hinge.

Finishes:

  • Nickel Plated
Click here for Information & Pricing

1-1/4" Steel Take-Apart Hinge

1-1/4
  • Hinge has 2 knuckle design.
  • Hinge slips apart at knuckle so lid or door may be easily removed.
  • Steel base material.
  • Joint length is 1-1/4".
  • Open width is 1-1/2".
  • Uses #6 pan head screws (not included but offered for purchase during checkout). Uses 4 screws per hinge.

Finishes:

  • Nickel Plated
Click here for Information & Pricing

2-1/4" Steel Take-Apart Hinge

2-1/4
  • Hinge lifts apart so lid or door may be easily removed.
  • Joint length is 2-1/4".
  • Open width is 1-7/8".
  • Steel base material.
  • Uses #8 pan head screws (not included but offered for purchase during checkout). Uses 4 screws per hinge.

Finishes:

  • Zinc Plated
Click here for Information & Pricing

1-3/4" Stainless Steel Quick Release Hinge

1-3/4
  • "Quick Release" hinge features a hinge pin release mechanism that allows door or lid to be easily removed.
  • Hinge pin is spring loaded to keep the door or lid safely locked on to the cabinet or box.
  • To remove the door or lid, the hinge pin may be retracted by pushing the knurled knob down and pivoting it into the unlocked position.
  • Hinge is designed to be surface mounted.
  • Hinge measures approximately 1-3/4" tall and 2" wide in the open position.
  • Made from solid stainless steel.
  • Uses #6 pan head screws (4 screws per hinge), not included, but offered for purchase during checkout.
  • PLEASE NOTE: These hinges are handed (Right Hand or Left Hand). Make sure to order one Right Hand AND one Left Hand hinge for each door or lid you are hanging. The image shown to the left is a "Right Hand" model.

Finishes:

  • Satin Stainless Steel
Click here for Information & Pricing

2-5/16 Inch Lift-Off Hinge

2-5/16 Inch Lift-Off Hinge
  • Small hinge for exterior shutters or doors.
  • "Lift-off" feature allows shutter or door to be easily removed after installation.
  • Hinge is made to be surface mounted.
  • Hinge is non-handed. Will work on either left hand or right hand shutters.
  • Hinge measures 2-5/16" tall by 1-7/8" wide in the open position as shown in the photo.
  • Made from steel and zinc chromate plated.
  • Wood screws are included.
  • Sold by the pair. A pair is two complete hinges which is normally what is needed to hang one shutter.
Click here for Information & Pricing
accredited business BBB
Sign up for email updates from HardwareSource and get 5% OFF your next order!
Email:

see what customers are saying

Over 10,000 Reviews
5 Star Average

High quality, received them promptly without special shipping. Great quality, saved over 100.00 over Home Depot. ... (Read review)
Thank you for helping us find the hinges no store had! We are were very happy to find the hinges we were looking for - they look great ...
Guaranteed: All Valid Reviews Posted
StatisticsReview of HardwareSource.com