Glass Door Hinges

Glass Door Hinges

  • Hinges for doors made of glass.
  • There are over 50 different type of glass door hinges in this section.
  • Both non-bore and bore type glass door hinges.

European Glass Door Hinge

European Glass Door Hinge
  • Available in three types:
    • Straight Arm hinges for overlay doors
    • Half Cranked hinges for back to back doors
    • Full Cranked hinges for inset doors
  • Also available are plastic decorative cover caps
    • Round style in Gold, Silver, Chrome and Black
    • "D" shaped in Gold, Silver and Chrome
  • Also available are white or black hinge covers
Click here for Information & Pricing

Blum European Style Glass Door Hinges

Blum European Style Glass Door Hinges
  • European style glass door hinges for inset, overlay and twin overlay glass doors.
  • Hinges feature a 94 degree opening angle and 3 dimensional adjustment.
  • This hinge system requires that the glass door have a 26mm hole bored for each hinge used.
  • They work with glass thicknesses of 4.5mm to 7mm (slightly under 3/16 to slightly over 1/4 inch).
  • The hinge system is made up of 4 items which are ordered separately; the hinge, the cover cap, the mounting plate and the wood screws for the mounting plate.
  • The hinges come in 3 types; "Straight Arm" for overlay doors, "Half Cranked" for twin overlay doors (also known as "Back-to-Back" doors, and "Full Cranked" for inset doors.
  • The "Cover Caps" (required to hold glass door to hinge system) are available in 2 finishes; (Black andChrome), and two types (Roundand D-shaped). Screws to hold cover cap to hinge are included with hinge.
  • All parts of the hinge and cover cap that touch the glass are plastic material.
  • PLEASE NOTE: The hinges on this page require mounting plates (and screws) and cover caps to work. Please make sure to order one mounting plate and one cover cap for each hinge ordered. Cover caps are found on this page. Each mounting plate requires two screws.

Accessories available for this hinge (Offered for purchase at check-out):

  • Mounting plates for frameless applications, required for installation.
  • Hinge cover caps, covers adjustment screws, dresses up the hinge (SKU 268004)
  • Glass door pull.

Finishes:

  • Black Cover Cap
  • Chrome Cover Cap
Click here for Information & Pricing

Inset Glass Door Hinge, Bore Type

Inset Glass Door Hinge, Bore Type
  • Inset type glass door hinge.
  • Requires two holes (approximately 3/8") bored in glass to install.
  • Hinge measures approximately 1-7/8" tall.
  • Leaf that attaches to glass is about 1-3/8" wide.
  • Leaf that attaches to side panel is about 2" wide.
  • Screws to attach hinge to side panel are not included (uses #6 Pan Head, stainless steel screws are offered for purchase during checkout). All other fasteners are included.
  • The hinge body is polished stainless steel (type 304). The fixing plate (attaches to front of glass) is made from zinc allow and is polished chrome plated.
  • For glass thicknesses from 3/16" to 5/16".
  • For glass doors up to 26 lbs and 25.5" wide (per pair of hinges).

Finishes:

  • Polished Chrome and Polished Stainless Steel
Click here for Information & Pricing

Large Inset Non-Bore Glass Hinge

Large Inset Non-Bore Glass Hinge
  • Glass door hinge for inset doors. No boring of glass is required.
  • Made from Type 304 stainless steel.
  • For glass doors 5/32" to 5/16" thick and up to 51" tall and 17-3/4" wide.
  • Screws are included.
  • Hinge measures approximately 2-3/8" tall and 1-1/4" wide and 3/4" thick.
  • For exact dimension click on link below.

Finishes:

  • Polished Stainless Steel
Click here for Information & Pricing

Glass Door Hinge, Stainless Steel, Non-Bore Inset

Glass Door Hinge, Stainless Steel, Non-Bore Inset
  • Glass door hinge for inset applications
  • Fits glass thickness of 4 to 8 mm (5/32" to 5/16").
  • Hinge clamps to glass so no boring of glass is required. Clamp screws are included.
  • Type 304 stainless steel.
  • Maximum door size is 15-3/4" high by 23-5/8" wide.
  • Hinge measures approximately 1" high by 1-1/4" wide by 3/4" thick. See dimensional diagram for actual measurements.
  • Flat head wood screws are included.

Finishes:

  • Polished Stainless Steel
Click here for Information & Pricing

Glass Door Hinge, Non-Bore Inset

Glass Door Hinge, Non-Bore Inset
  • installs easily without boring through glass doors
  • positive self-locking feature eliminates the need for magnetic or touch latches
  • glass secured with large rubber tipped screw
  • opening angle is 160 degrees
  • hinge measures approximately 1-3/16" tall and each hinge wing is approximately 1-1/2" wide.
  • for left or right hand installations
  • glass thickness to 1/4"
  • steel base material
  • this hinge is sold by the "Pair". A pair is what is required to hang one door.
  • uses #6 round or pan head screws (not included). Uses 4 screws per pair of hinges.

Finishes:

  • Chrome plated
  • Brass plated
Click here for Information & Pricing

Glass Door Hinge, Non-Bore Inset, Side Mount

Glass Door Hinge, Non-Bore Inset, Side Mount
  • Installs easily without boring through glass doors.
  • Includes self adhesive pressure plates and screws.
  • Screw-mounts to side of cabinet.
  • Opening angle is 110 degrees.
  • For left or right hand installations.
  • For glass thicknesses of 3/16" to 1/4".
  • Side mount plate measures 1-1/2" by 5/8" by 5/8". Glass bracket measures 1-5/8" x 3/4" tall by 1/2" thick.
  • Made from steel base material.
  • Uses #4 pan or round head screws (not included). Uses 4 screws per pair of hinges.
  • PLEASE NOTE: The manufacturer of this hinge does not make or supply the wood screws for this hinge. We have searched the market for black round or pan head screws, brass round or pan head screws and chrome round or pan head screws without success. Our dilemma is that we can choose to not offer the hinge or we can choose to offer the hinge with screws that will work but are not perfect. We believe that it is best to offer the hinges, advise the consumer and let the consumer make the final choice. When you check out, you will be offered pan head stainless steel screws which will fit the hinge. If you buy the black or brass hinge and you want the screw head to match the hinge you will have to apply some sort of paint to the screw head. If you buy the chrome hinge,a stainless steel screw is only a fair match to chrome.

Finishes:

  • Chrome plated
  • Brass plated
  • Black
Click here for Information & Pricing

Small Glass Door Hinge, Non-Bore Inset

Small Glass Door Hinge, Non-Bore Inset
  • Installs easily without boring through glass doors.
  • Opening angle is 110 degrees.
  • For left or right hand installations.
  • For glass thicknesses to 1/4" (6.5mm).
  • Visible height is 20 mm (Approx. 25/32").
  • Outside diameter of pivot point bushing is 5/16".
  • Made from steel base material.
  • Includes self adhesive pressure plates, machine screws, press-fit black plastic bushings and set screws to hold glass.
  • PLEASE NOTE: Image shows the set screws that hold the glass in place. Normal installation of this hinge will have the set screws positioned on the inside of the cabinet so they will not be visible when the door is in the closed position.

Finishes:

  • Chrome plated
  • Black finish
Click here for Information & Pricing

Glass Door Hinge, Non-Bore Inset, 13.5mm

Glass Door Hinge, Non-Bore Inset, 13.5mm
  • Installs easily without boring through glass doors.
  • Includes self-adhesive pressure plates, machine screws, press-fit black plastic bushings, and set screws to hold glass.
  • Sold by the pair. A pair will hang one glass door.
  • Opening angle is 110 degrees.
  • For left or right hand installations.
  • To install the press-fit black plastic bushing, drill a 3/8" diameter hole (1/4" depth).
  • Glass thickness to 3/16" (5 mm).
  • Visible height is 13.5 mm (Approx. 17/32").
  • Made from steel base material.

Finishes:

  • Chrome plated
  • Brass plated
  • Black finish
  • Satin Nickel finish
Click here for Information & Pricing

Glass Door Pulls

Glass Door Pulls
  • Slide-on pulls for small glass doors.
  • Made for glass doors up to 3/16" thickness.
  • Pull features a built-in finger grip.
  • Made from steel base material.
  • Available in 4 finishes.
  • Pulls measure 1-9/16" tall by 7/8" wide by 3/8" thick (not including finger pull).
Click here for Information & Pricing

180 Degree, No-Bore, Inset Glass Door Hinge

180 Degree, No-Bore, Inset Glass Door Hinge
  • Glass door hinge for inset doors.
  • Opens 180 degrees.
  • For glass thicknesses of 4 to 6 mm (5/32" to 1/4").
  • Glass is held in place by nylon screw, no holes are required in glass.
  • Rated for a maximum door size of 800 mm tall by 350 mm wide.
  • Hinge features a built-in latch to hold the door in the closed position.
  • Uses 2 each #6 flat head wood screws (not included but offered for purchase during checkout).
  • Made from diecast material and nickel plated. Latching mechanism and holding screw aremade from black nylon.
  • Our SKU 701132 (Glass Door Pull, Nickel Plated) is made to go with this hinge. This item is offered for purchase during checkout.
  • IMPORTANT PLEASE NOTE: For each door that you are hanging, you need to order one "Right Hand" model hinge (SKU 701128) and one "Left Hand" hinge (SKU 701126). Image above shows Right Hand model (SKU 701128).
Click here for Information & Pricing

Compact Glass Door Hinge

Compact Glass Door Hinge
  • Compact hinge for stereo cabinet sized glass doors.
  • Made for Inset doors.
  • Bore information
    • Size of bore in glass is 19mm (3/4").
    • Bore dimension (distance from edge of glass to edge of 19mm hole) is 8mm (5/16").
  • Opening angle 90 to 105 degrees. Opening angle depends on glass thickness:
    • 4.5 mm glass will open to 105 degrees
    • 5 mm glass will open to 105 degrees
    • 5.5 mm glass will open to 100 degrees
    • 6mm glass will open to 95 degrees
    • 6.5 mm glass will open to 90 degrees
  • Weight rating
    • 14 lbs for 2 hinges per door
    • 22 lbs for 3 hinges per door
  • A cabinet catch is not required with this hinge. Hinge has a "detent" which holds the door in the closed position.
  • Hinge is solid brass, pivoting screw ismade from steel, plastic washers are included to cushion glass.
  • Each hinge uses 2 each #6 round head wood screws to mount the hinge to the cabinet side panel. Not included but offered for purchase during checkout. Use our SKU 286252.

Please Note: Unfortunately, this hinge has been discontinued by the manufacture.We are currently looking fora replacement.

Finish:

  • Antique Brass (SKU 701130)
Click here for Information & Pricing

Glass Door Hinge, Overlay Type, Non-Bore

Glass Door Hinge, Overlay Type, Non-Bore
  • Glass door hinge for overlay type doors.
  • For frameless type cabinets.
  • Hinge mounts in the upper corner and the lower corner of the cabinet and attaches to the inside of the side panel and to the top and bottom panel of the cabinet. See the support link below for an installation diagram.
  • Made for 3/16" to 1/4" thick glass. No boring or drilling of glass is necessary.
  • Hinge allows door to open to approximately 180 degrees.
  • After installation the glass will overlay the cabinet frame by 7/32".
  • Made from steel and available in three finishes
    • Polished Brass
    • Semi-Gloss Black
    • Polished Chrome
  • This hinge is sold by the "Pair". A pair means one top hinge and one bottom hinge, enough to hang one glass door.
  • Each pair of hinges attaches with 6 each, #6 or #7 wood screws. Screws are not included but are offered for purchase during checkout.
  • Since there are three different finishes, our reccommended screws are listed below
    • For SKU 286210 (Brass finish) use our SKU 135278
    • For SKU 286214 (Black finish) use our SKU 778159
    • For SKU 286212 (Chrome finish) use our SKU 135404
Click here for Information & Pricing

Glass Door Pull, Nickel Plated

Glass Door Pull, Nickel Plated
  • Glass door pull is made from diecast zinc material and is nickel plated.
  • Can be used with almost any insetglass door hinge, but is made as a match for our 180 Degree, No-Bore, Inset Glass Door Hinge (SKU #701128 and # 701126).
  • Pull slips over the glass and installs using a piece of double stick tape (included) and by tightening a nylon fixing screw.
  • Pull measures approximately 1" tall by 1" wide. The finger pull projects from the glass approximately 13/16".
  • Works on glass thicknesses of 4 mm to 6 mm.
  • For inset glass doors, there must be a minimum of 2mm of reveal between the edge of the glass and the side panel of the cabinet.
Click here for Information & Pricing

Stainless Steel 3/8" Overlay Glass Door Hinge

Stainless Steel 3/8
  • Glass door hinge for overlay doors.
  • Stainless steel base material with an aluminum cap screw.
  • Free swinging.
  • Uses #4 flat head wood screws (not included but offered for purchase during checkout.) Order 3 screws per hinge.
  • Overlay dimension is 3/8".
  • Requires a 7mm hole drilled in the glass.
  • Maximum door weight is 8.8 lbs per pair of hinges.
  • For glass thicknesses of 4mm (5/32"), 5mm (3/16") and 6mm (15/64")

Finishes:

  • Stainless Steel
Click here for Information & Pricing

Inset Glass Door Hinge

Inset Glass Door Hinge
  • Glass door hinge for inset doors
  • Requires a 7mm hole drilled in the glass
  • Free swinging
  • For glass thicknesses of 4mm (5/32"), 5mm (3/16"), and 6mm (15/64")
  • Maximum door weight for a pair of hinges is 8.8 lbs
  • Maximum door size is 17-3/4" wide by 27-1/2" high per pair of hinges
  • Uses #4 flat head wood screws (not included but offered for purchase during checkout) Order 3 each screws per hinge.
  • Made from steel base material.

Finishes:

  • Polished Chrome
  • Polished Brass
Click here for Information & Pricing

Glass Door Overlay Hinge, Bore Type

Glass Door Overlay Hinge, Bore Type
  • Glass door hinge for cabinets without a face frame.
  • Hinge overlays side panel.
  • Hinge requires small hole bored in glass to install
  • Steel base material. Snap catch is made from nylon.
  • Uses #4 flat head screws not included but offered for purchase during checkout. (for side panel attachment). Order 3 each screws per hinge.
  • Fasteners to attach hinge to glass are included.
  • Hinge features built in nylon snap catch to hold door in closed position.
  • Hinge shown in photo is chrome hinge. Hinge is show in 1/2 open position.

Finishes:

  • Chrome
  • Polished Brass
  • Flat Black
Click here for Information & Pricing

Magnetic Touch Latches and Plates for Glass Doors

Magnetic Touch Latches and Plates for Glass Doors
  • Magnetic touch latch and steel plate work together to provide a latch for glass doors.
  • To operate the touch latch simply push it in, it will then pop the glass door out so it can be easily opened.
  • Use the single touch latch where there is only one door.
  • Use the double touch latch where two doors close together in the middle of the cabinet.
  • Use the "Push-In" touch latch where you have a wooden horizontal shelf. The Push-In touch latch pushes into a hole drilled in the edge of the shelf.
  • The wrap around plates are available in 3 finishes.
  • The wrap around plate is made out of steel so as to work with the magnet in the touch latch.
  • The wrap around plates will work for 3/16" thick glass and include self adhesive plastic cushioning material for the glass. They are held in by pressure.
  • The wrap around plates will work for 1/4" glass if you shim the glass with a small piece of plastic tape. Discard the self adhesive plastic cushioning material.
  • IMPORTANT: Screws are not included but are offered for purchase during checkout:
    • The Double Touch Latch (SKU 796073) uses #4 Round Head Screws (4 each).
    • The Single Touch Latch (SKU 796071) uses #4 Round Head Screws (4 each).
    • The Push In Touch Latch (SKU 796075) uses #4 Flat Head Screws (2 each).
  • Be sure to order one wrap around plate for each glass door.

Finishes:

  • Black Plastic (Single Touch Latch)
  • Black Plastic (Double Touch Latch)
  • Black Plastic (Push-In Touch Latch)
  • Polished Brass (Plate)
  • Polished Chrome (Plate)
  • Black (Plate)
Click here for Information & Pricing

Shower Door Hinge, Glass to Wall

Shower Door Hinge, Glass to Wall
  • Used for standard wall to glass installation.
  • Solid brass drop forged construction.
  • Stainless steel reversible hinge pin.
  • Opens to 90 degrees
  • Hinge pin is reversible which allows it to be set at 0 degrees or 5 degrees. The 5 degree setting holds the door against a stop.
  • Springs are hardened stainless steel coil springs.
  • Fits tempered glass sizes from 3/8" to 1/2"
  • Wall plate measures 1-15/16" by 3-1/2" tall. Glass leaf measures 2-1/8" by 3-1/2" tall.
  • Hinge is designed to fit industry standard templates.
  • Comes complete with gaskets and allen wrench. Does not include wall mount screws.
  • PLEASE NOTE; installation of this hinge requires a cutout in the glass where the hinge is installed.

Weight rating using 3/8" glass; using 2 hinges maximum weight is 80lbs and 28" maximum width. Using 3 hinges maximum weight is 120lbs and 32" maximum width.

Weight rating using 1/2" glass; using 2 hinges maximum weight is 80lbs and 26" maximum width. Using 3 hinges maximum weight is 120lbs and 30" maximum width.

Finishes:

  • Bright Chrome
  • Brushed Nickel
Click here for Information & Pricing

Shower Door Hinges, 180 Degree, Glass to Glass

Shower Door Hinges, 180 Degree, Glass to Glass
  • Used for standard glass to glass installation.
  • Solid brass drop forged construction.
  • Stainless steel reversible hinge pin.
  • Opens to 90 degrees
  • Hinge pin is reversible which allows it to be set at 0 degrees or 5 degrees. The 5 degree setting holds the door against a stop.
  • Springs are hardened stainless steel coil springs.
  • Fits tempered glass sizes from 3/8" to 1/2"
  • Each glass leaf measures 2-1/4" wide by 3-1/2" tall.
  • Hinge is designed to fit industry standard templates.
  • Comes complete with gaskets, screws, allen wrench.
  • PLEASE NOTE; installation of this hinge requires a cutout in the glass where the hinge is installed.
  • Please Note: The photograph shows the Satin Nickel finish which has been discontinued.

Weight rating using 3/8" glass; using 2 hinges maximum weight is 80lbs and 28" maximum width. Using 3 hinges maximum weight is 120lbs and 32" maximum width.

Weight rating using 1/2" glass; using 2 hinges maximum weight is 80lbs and 26" maximum width. Using 3 hinges maximum weight is 120lbs and 30" maximum width.

Finishes:

  • Oil Rubbed Bronze
Click here for Information & Pricing

Shower Door Hinges, 135 Degree, Glass to Glass

Shower Door Hinges, 135 Degree, Glass to Glass
  • Used for standard glass to glass installation.
  • Solid brass drop forged construction.
  • Stainless steel reversible hinge pin.
  • Used to mount a door to a fixed glass side panel that runs at a 135 degree angle to the door.
  • Hinge pin is reversible which allows it to be set at 0 degrees or 5 degrees. The 5 degree setting holds the door against a stop.
  • Springs are hardened stainless steel coil springs.
  • Fits tempered glass sizes from 3/8" to 1/2"
  • Each leaf measures 2/1/8" wide by 3-1/2" tall.
  • Hinge is designed to fit industry standard templates.
  • Comes complete with gaskets, screws, allen wrench.
  • PLEASE NOTE; installation of this hinge requires a cutout in the glass where the hinge is installed.

Please Note: These hinges have been discontinued, the only finish we have left in stock is the oil rubbed bronze finish.

Weight rating using 3/8" glass; using 2 hinges maximum weight is 80lbs and 28" maximum width. Using 3 hinges maximum weight is 120lbs and 32" maximum width.

Weight rating using 1/2" glass; using 2 hinges maximum weight is 80lbs and 26" maximum width. Using 3 hinges maximum weight is 120lbs and 30" maximum width.

Finishes:

  • Oil Rubbed Bronze
Click here for Information & Pricing

Shower Door Hinges, 90 Degree, Glass to Glass

Shower Door Hinges, 90 Degree, Glass to Glass
  • Used for standard glass to glass installation.
  • Solid brass drop forged construction.
  • Stainless steel reversible hinge pin.
  • Opens to 90 degrees
  • Hinge pin is reversible which allows it to be set at 0 degrees or 5 degrees. The 5 degree setting holds the door against a stop.
  • Springs are hardened stainless steel coil springs.
  • Fits tempered glass sizes from 3/8" to 1/2"
  • Each leaf measures 2-1/4" wide by 3-1/2" tall.
  • Hinge is designed to fit industry standard templates.
  • Comes complete with gaskets and allen wrench. Does not include wall mount screws.
  • PLEASE NOTE; installation of this hinge requires a cutout in the glass where the hinge is installed.

Weight rating using 3/8" glass; using 2 hinges maximum weight is 80lbs and 28" maximum width. Using 3 hinges maximum weight is 120lbs and 32" maximum width.

Weight rating using 1/2" glass; using 2 hinges maximum weight is 80lbs and 26" maximum width. Using 3 hinges maximum weight is 120lbs and 30" maximum width.

Finishes:

  • Brushed Nickel
Click here for Information & Pricing
accredited business BBB
Sign up for email updates from HardwareSource and get 5% OFF your next order!
Email:

see what customers are saying

Over 10,000 Reviews
5 Star Average

Very reliable vendor - would do business with again. Very prompt shipping and the order was processed flawlessly! ...
High quality, received them promptly without special shipping. Great quality, saved over 100.00 over Home Depot. ... (Read review)
Guaranteed: All Valid Reviews Posted
StatisticsReview of HardwareSource.com