• Hettich Flap hinge, Markant 7.1 for overlay installations.
• For installation of "fold down" flaps.
• Fold Down Flaps are used on desks, drawers, etc. The hinge allows the front flap to fold down creating a horizontal work surface.
• Complete unit is made up of two hinges (a right hand and a left hand hinge) and two mounting plates. Flap can be removed from desk after installation by loosening the screw on the mounting plate.
• After installation both the depth and the height of the hinge may be adjusted plus or minus 2 mm.
• Made from steel base material and nickel plated.
• The hinges fit into a 35mm (1-3/8") cup drilled into the surface of the flap.
• Hinge in the photo shows the "Left Hand" hinge (SKU 306200)
• PLEASE NOTE:To hinge a flap you need to order 4 items:
  • one Right Hand Hinge (SKU 306202)
  • one Left Hand Hinge (SKU 306200) and
  • two mounting plates (SKU 306205)
• Fasteners
  • Each hinge requires 2 each #6 flat head wood screws, not included but offered for purchase during checkout. Order 2 each SKU 652360.
  • Each mounting plate comes with 2 system screws. System screws fit into 5 mm holes that are usually pre-drilled in the cabinet and spaced 32 mm apart. If you are not using the system screws you should order #10 pan head screws (2 for each mounting plate).
• PLEASE NOTE: Most of our products are not packaged for retail sale and as such do not contain instructions. We recommend that, if you are placing an order for this product, you print out the installation information found at the links below.

• High quality American made hinge
• Hinge measures 2" high (hinge pin length) by 3" wide by 1/8" thick
• Solid Brass base material
• Matching flat head wood screws are included

Finishes:

• Antique Brass

• Butt hinge has a polished brass finish.
• Clear coated for a lasting finish.
• Solid brass base material.
• "Joint length" is the distance from the top of the hinge pin to the bottom of the hinge pin.
• Wood screws are included.
• This hinge is sold by the pair. There are two complete hinges per pair.

Finishes:

• Polished brass

• High quality American made product
• Hinge measures 1-1/2" high (hinge pin length) by 2-3/8" wide by 3/32" thick
• Solid Brass base material
• Matching flat head wood screws are included

Finishes:

• Antique Brass

• for heavy cabinet work, folding shelves and table drop leaves
• hinge is a surface mounted hinge (may be partially mortised into the surface)
• fast spun pins
• hole patterns and number may vary from picture depending on size of hinge
• steel base material
• maximum door weight for 1-1/2" hinge is 30 lbs per pair, the 2" hinge is 35 lbs per pair.
• wood screws are included

Finishes:

• Zinc Plated

• hinge is used on the drop flap of a writing desk
• measures 3" long by 1/2" wide by 1/8" thick
• solid brass base material
• comes with matching flat head wood screws

Finishes:

• Antique Brass

• 3-1/8" open
• 1-3/16" wide
• 1/16" material thickness
• steel base material
• uses #8 flat head screws (not included but offered for sale during checkout).

Finishes:

• Brass plated

• 3-1/8" open
• 1-3/16" wide
• 1/16" material thickness
• Steel base material
• Uses #8 flat head screws (not included)

Finishes:

• Bronze plated

• Flap stays hold flap or desk top in horizontal position.
• They are meant to be used in conjunction with a hinge.
• By tightening the screws on the white plastic block, friction is increased to control how fast the flap drops.
• Available in 2 sizes.
• Screws are not included but are offered for purchase during checkout. Order 2 each #6 flat head screws for plastic blocks. Order 2 each #4 flat head screws for base attachment.

Finishes:

• Nickel plated steel, white plastic

• Drop stay gently lowers and holds drop down desk surfaces and flaps.
• Reversible, can be installed on left or right hand side.
• Length is approximately 9". For detailed dimensions, click on link below.
• This product is meant to be used with separate hinges.
• Click on the link below to see what flap sizes this product will support.
• Screws are included.

Finishes:

• Nickel plated steel, black plastic

• For secretary type desks.
• Hinge opens desk top to horizontal position.
• After installed, desk top will close to about 45 degrees (or 135 degrees from horizontal).
• Overall length of hinge is 7" in open position.
• Width of hinge is 3/4".
• Steel base material.
• Matching wood screws are included.

Finishes:

• Brass plated

• This device may be used for limiting the swing of a cabinet door anywhere from 0 to slightly more than 90 degrees depending on how you elect to install the mounting plates.
• A typical installation would be to mount the right angle swivel plate on the inside surface of the door and to mount the second plate on the underside of a shelf or the underside of the top of the cabinet.
• Available in a "Left Hand" or "Right Hand" model.
• Use a "Right Hand" model if your door is hinged on the right hand side of the cabinet as you are facing the cabinet.
• This device may also be used to support drop down desk tops. If ordering for use as a drop down desk support, order one "Left Hand" and one "Right Hand" model.
• Uses 2 each #4 flat head screws (not included but offered for purchase during checkout).
• PLEASE NOTE: the photos to the left show the product in a vertical position. When used as a cabinet restraint they will be installed in a horizontal positon.

Finishes:

• Nickel

• Lid support is convertible, reversible, adjustable and demountable.
• Can be used on a horizontal lid, a vertical lid or a drop down lid.
• The friction on the lid support is adjustable. It is active in one direction with no friction in the opposite direction.
• Both lid support attachments are demountable (they snap out) from from the lid support.
• The demountable feature allows you to reverse the direction that the friction is applied.
• The slide button near the hub of the lid support allows you to change the direction of the friction action from up-opening to down-opening.
• Overall length of lid support is approximately 8" not including attachment ends.
• Two lid supports can support a lid weighing up to 20 lbs.
• Made from die cast zamak
• Uses #6 flat head screws (not included but offered for purchase during checkout). Uses 4 screws per lid support.

Finishes:

• Nickel Plated

• Hettich flap stay supports fold down desk tops.
• Available in 6 sizes.
• Choose a size that fits your "Cabinet Internal Height" (see Installation Diagram #1).
• Features a brake adjustment screw to control braking action.
• Made from steel and die cast parts with nylon internal parts.
• Each flap stay uses 6 each #6 flat head screws (not included but offered for purchase during checkout).
• Non-handed; works on both right hand and left hand applications.
• Also offered for purchase during checkout is our "Metal Flap Hinge" used for hinging the drop down flap to the desk.
• For flap dimensions see "Click here for install diagram #2" link below.

• Flap hinge made by Hettich.
• For desks with a drop down front or flap.
• Allows flap to fold down and hold at 90 degrees creating a desklike worksurface.
• Hinge parts are mounted separately allowing disassembly of flap and bottom panel.
• Hinge is adjustable 3 ways after installation.
• Requires a 35mm (1-3/8") hole in the flap and bottom panel. See link below for exact hole dimensions.
• Hole edge breakout is covered by hinge lip.
• Hinge measures 2-9/16" by 1-9/16", measured at its widest points.
• Depth of hole that hinge fits into is 15/32".
• Made from precision die cast material.
• Matching wood screws are included.

Finishes

• Satin Nickel
• Satin Brass
• Dark Bronze

• Allows panel to fold down and hold at 90 degrees
• Fits a 35mm (1-3/8") hole
• Hinge is detachable and adjustable
• Zinc die cast material
• Hinge measures 2-3/16" by 1-1/2", measured at its widest points.
• Hinge thickness is 15/32"
• Screws are not included

Finishes:

• Dark Bronze
• Nickel

• flap opens 90 degrees, flush with inside shelf
• fits flush in door & shelf surfaces, concealed from exterior
• 30mm Forstner or flat boring bit needed to install
• for 3/4" thick doors
• hinge thickness is 7/16"
• linkage is brass and steel
• hinge is made from nylon material
• Uses #4 x 5/8" oval head wood screws (Not included)

Finishes:

• White nylon

• Flap opens 90 degree flush with inside shelf
• Fits flush in door & shelf surfaces, concealed from exterior
• Click on link below for more install information
• Uses #3 Flat head screws (not included)

Finishes:

• White plastic and Chrome plated

• Flap opens 90 degrees flush with inside shelf
• Fits flush in door & shelf surfaces, concealed from exterior
• Click on link below for more install information
• Uses #4 Flat Head screws (not included)

• Finishes:
  • Nickel plated