Finishes:

• Primed for painting 600 (USP)
• Bright brass plated steel 632 (US3)
• Satin bronze plated, blackened, satin relieved, clear coated 643 (US11) (similar to oil rubbed bronze, but on steel)
• Satin chrome plated steel 652 (US26D)

Finishes:

• 605 (US3) polished brass
• 613 (US10B) oil rubbed bronze
• 625 (US26) bright chrome plated
• 626 (US26D) satin chrome plated
• 629 (US32) stainless steel, bright
• 630 (US32D) stainless steel, satin

Finishes:

• 605 (US3) polished brass
• 613 (US10B) oil rubbed bronze
• 625 (US26) bright chrome plated
• 626 (US26D) satin chrome plated
• 629 (US32) stainless steel, bright
• 630 (US32D) stainless steel, satin

• Dependable and versatile floor-concealed door closer made by Dorma. Model number is BTS80.
• For center hung doors (includes center hung door package B). Package B is for wood doors. It uses Dorma's spring #2.
• Door closer is double acting (opens in both directions unless a stop is installed in the door frame) and non-handed (works on both left hand and right hand opening doors).
• Compact body allows installation in thin slab concrete subfloor construction.
• Can control exceptionally heavy single and double acting doors.
• Includes an adjustable "hold open" feature at any point past 80 degrees (feature can be turned on or off).
• Product comes with the standard 74010 spindle which gives a 3/4" clearance between the bottom of the door and the floor surface. Other spindles may be special ordered if a different clearance is desired. Call our office for details.
• The range of door widths for exterior doors is 2'6" to 3'6". For interior doors 2'6" to 4'0". Maximum door weight is 660 lbs.
• Also available for special order is a "terrazo pan". The terrazo pan allows the closer to be concealed using your flooring material instead of the metal plate shown in the photo. Call our office to order this pan.
• For technical data click on the link below which will take you to the manufacturers website.

Finishes:

• Satin Chrome US26D
• Oil Rubbed Bronze US10B
• Polished Brass US3

Finishes:

• 605 (US3) polished brass
• 613 (US10B) oil rubbed bronze
• 625 (US26) bright chrome plated
• 626 (US26D) satin chrome plated

• For doors up to 150 lbs
• Designed for mullion or frame mounting
• For overlay doors 1-3/8" to 1-3/4" thick
• Doors can be installed floor to ceiling
• Full 180 degree opening
• Extra long screws are included
• Horizontal piece (as shown in photo)measures 3" by 1-1/2"
• Vertical flat piece (which mounts to wall) measures 3"
• Rounded piece comes out from wall 2-15/16"

Finishes:

• Satin Chrome Plated (US26D)

• Pivot hinges for Cafe Doors.
• Cafe doors are small lightweightdoors that swing open in both directions.
• Available only in brass plated finish.

• Pivot hinge set is made for arch top (curved top) doors.
• Set consists of two intermediate pivot hinges and a bottom pivot hinge.
• Hinge set allows door to swing up to 180 degrees (depending on trim).
• For door weights up to 500 lbs.
• For door heights ranging from 60" to 90" and door widths up to 3 feet 6 inches.
• Set includes wood screws, machine screws and masonary anchors for the bottom pivot.
• Hinge set us UL Listed.
• Bottom pivot attaches to floor.
• Pivot point of hinge set is 3/4" (measured to face of door).
• Door edges must be beveled (1/8" in 2").
• Made from solid brass and steel parts.
• Hinge sets are handed. Order either a Left Hand or Right Hand model depending on which way you want your door to open. Hinge in photo is a "Left Hand" model.

Finishes:

• Primed for painting 600 (USP)
• Satin brass plated steel 633 (US4)

• Spring pivots are typically used for half height doors (or doors of less than full height).
• The Spring Pivot Hinge is a double acting hinge. Hinge swings 90 degrees in both directions and returns to center.
• Spring tension is adjustable.
• Hinge is not handed, works on both right and left hand doors.
• Hinge does not have the "hold open" feature.
• Maximum door width is 36".
• Minimum door thickness is 1".
• Maximum door thickness is 2-1/2".
• Maximum door weight is 75 lbs.
• This hinge requires a minimum clearance of 4.5" from the bottom of the door to the floor and a minimum clearance of 1/2" from the top of the door to the door jamb.
• Picture shows one set (top and bottom pivot).
• Base material is malleable iron base.
• Screws are included.

Finishes:

• Primed for painting 600(USP)
• Satin brass 633(US4)
• Satin chrome 652(US26D)

• This Mortise Mount Spring Pivot differs from our Surface Mount Spring Pivot in that both the bottom and top units (pivots) may be mortised into the door. Note the difference in the placement of the door bracket on the spring cylinder.
• The 2.5" diameter spring cylinder on the bottom pivot can be mortised into the door. Since the maximum door thickness that the unit will accomodate is 2.5" the cylinder will show and be flush with a 2.5" thick door.
• The Spring Pivot Hinge is a double-acting hinge. The hinge swings 90 degrees in both directions and returns to center.
• Spring tension is adjustable.
• Hinge does not have "Hold Open" feature.
• Base is cast steel. Hinge sits on ball bearings.
• Hinge is non-handed, works on both left hand and right hand gates and doors.
• Maximum door width is 36". Maximum door thickness is 2.5". Maximum door weight is 75lbs.
• The door jamb bracket is 1-1/4" in width.
• Minimum doorthickness is 1" .
• Wood screws are included.
• Picture shows one set. A set is the top pivot and the bottom pivot. A set will hang one door or gate.

Finishes:

• Gear boxes are satin brass plated
• Pivots are prime coated

• Spring loaded pivot set, holds open at 90 degrees, self closes at 45 degrees.
• For use on wood or metal doors up to 135 lb., not larger than 3.5 feet wide and 7 feet tall.
• Camtrol action makes possible a snug application without rounding of the door edge.
• Cam box mortises into wood floor.
• For door thicknesses of 1-3/8" to 1-3/4".
• Cam boxes are brass, door brackets are steel (satin chrome plated), cam box trim plates are brass (satin chrome plated).
• Each cam box measures 3-7/8" by 1-1/4" by 29/32" tall.
• Mounting fasteners and instructions are included.

Finishes:

• Satin Chrome

• Spring loaded pivot set, holds open at 90 degrees, self closes at 45 degrees.
• This product is the same as our SKU 234024 except that the bottom pivot surface mounts instead of installing in a mortise (cutout) in the floor. Made for masonry installations. This application requires a 1" gap between the bottom of the door and the surface of your floor.
• For use on wood or metal doors up to 135lb, not larger than 3.5 feet wide and 7 feet tall.
• Camtrol action makes possible a snug application without rounding of the door edge.
• Cam boxes are solid brass, door brackets are steel (satin chrome plated). Cam box trim plates are brass (satin chrome plated).
• For door thicknesses of 1-3/8" to 1-3/4".
• Top cam box measures 3-7/8" by 1-1/4" by 29/32" tall.
• Bottom surface mount plate measures 3-7/8" by 3-1/4".
• Mounting fasteners and instructions are included.

Finishes:

• Satin Chrome

• For large cabinet doors and full size doors
• Made of solid brass with steel pins
• Flat head wood screws are included
• For SKU numbers 838198 to 838242 the pivot screw is flush with the hinge (as shown in photo to left).
• For SKU numbers 838250 to 838252, the pivot screw has a raised slotted head which measures about 3/4" in diameter and is 3/16" above the hinge surface.This large style pivot hinge pivots on roller bearings. A pivot base is available for these 3 SKU numbers only. It is offered for purchase during checkout.
• For tall doors an intermediate pivot hinge is recommended to keep the middle part of the door in alignment. Our SKU's 838204 through 838206 will work with any of the pivot hinges in this section. Intermediate pivots are offered for purchase during checkout.
• The listed weight ratings are for a pair of hinges.

Finishes:

• Polished Brass
• Satin Nickel
• Oil Rubbed Bronze

• This pivot base is used with our Large Pivot Hinges (SKU numbers 838250, 838251 and 838252 only).
• The pivot base replaces one leg of the pivot hinge (the non-door leg) to allow an easier installation if installing in concrete, marble, stone or any other material where a smaller cutout is desired.
• Pivot base measures approximately 1.25" in height by 1" in diameter at the top and 3/4" in diameter at the bottom.
• Made from solid brass.

Finishes:

• Polished Brass
• Oil Rubbed Bronze
• Satin Nickel

• These intermediate pivots work only with our pivot hinges in the SKU range from 838198 to 838252.
• An intermediate pivot hinge is used for taller doors to keep the middle part of the door in alignment with the pivot hinges at the top and bottom of the door.
• Made from solid brass material.
• Includes matching wood screws.
• Each hinge leaf measures 2-1/2" tall by 1-1/4" wide by 5/16" thick. Total width of hinge including hinge barrel is 2-1/2".

Finishes:

• Satin Nickel
• Polished Brass
• Oil Rubbed Bronze

• Pocket pivot hinge is also known as a Harmon hinge.
• This unique hinge is a "swing clear" type of hinge that allows a door to swing into a pocket at a right angle to the door frame.
• When the door is in the pocket it is completely clear of the door opening.
• The base material is made from solid stainless steel.
• Not handed, full mortise installation.
• Maximum door swing is 90 degrees.
• For doors weighing up to 270 lbs. use 3 hinges. For doors weighing up to 360 lbs use 4 hinges.
• Matching fasteners are included.
• PLEASE NOTE: THESE HINGES ARE A SPECIAL ORDER ITEM. THEY ARE PRODUCED AT THE TIME OF ORDER. THEY ARE NOT RETURNABLE AND THE LEAD TIME IS ABOUT 3-4 WEEKS.

Finishes:

• Polished Brass (US3)
• Satin Stainless Steel (US32D)
• Satin Bronze (US10)
• Polished Stainless Steel (US32)
• Oil Rubbed Bronze (US10B)