Door Stops, Holders,Restraints, Chain Bolts and Foot Bolts

Door Stops, Holders,Restraints, Chain Bolts and Foot Bolts

  • Hardware to control doors
    • Door Stops
    • Door Holders
    • Door Restraints
    • Overhead Door Holders
    • Hinge Pin Door Stops
    • Magnetic Door Stops
    • Chain Bolts
    • Foot Bolts

Overhead Door Holder & Stop

Overhead Door Holder & Stop
  • Door holders allow you to open the door to a set position between 85 and 110 degrees
  • The door then holds at that set position until you release it
  • Not handed, works on left or right hand opening doors
  • Designed for installation in virtually all types of doors and frames, including doors with conventional butt hinges, offset pivots, continuous hinges, swing clear hinges, Soss hinges and others.
  • Allows for variable mounting positions ranging from 85 degrees to 110 degrees of opening.
  • Available in two different types; One for door openings from 24"-30" and the other for door openings from 30"-36".
  • PLEASE NOTE; Overhead door holders are made from steel base material. The Satin Stainless steel model is made from stainless steel but has internal parts made from steel and other non-stainless steel materials.

Finishes:

  • Satin Stainless Steel
  • Oil Rubbed Bronze
  • Polished Brass
Click here for Information & Pricing

Chain Door Restraint with Springs

Chain Door Restraint with Springs
  • This heavy duty chain door restraint can be installed to restrict the swing of a full size door. For example in a windy area or in an area where the door would hit something if opened too far.
  • The chain door restraint is made up of two solid brass end brackets, each attached to a spring. The middle part is a heavy duty solid steel welded chain. The length of chain is covered by a grey vinyl covering.
  • Recommended for doors with a maximum width of 36".
  • Screws for the end brackets are included.
  • The total length of the chain door restraint is 26.5". The end bracket mounting plate measures 1.5" by 1.5

Finishes:

  • Oil Rubbed Bronze
Click here for Information & Pricing

Hinge Pin Door Stop, Adjustable

Hinge Pin Door Stop, Adjustable
  • adjustable doorstop installs in door hinge and is held in place by hinge pin
  • this hinge pin door stop is adjustable to stop the door at your choice of 5 different points
  • solid brass material
  • nylon hinge pin bearing (1/4" inside diameter)
  • rubber bumpers to protect door and door molding
  • size is approximately 3-1/2" x 2-1/4" as shown in the wide open position

Finishes:

  • Brass
  • Oil Rubbed Bronze
  • Satin Nickel
Click here for Information & Pricing

Hinge Pin Door Stop

Hinge Pin Door Stop
  • Installs under top of hinge pin on your door hinge to provide a door stop
  • Solid Brass base material
  • Adjustable
  • Rubber bumpers protect your door and molding around door jamb
  • Door stop has a nylon hinge pin bushing (not shown) with 1/4" inside diameter
  • The nylon hinge pin bushing can be removed which will provide a 5/16" inside diameter
  • Compact design (approximate size is 2-1/4" x 1-3/4")

Finishes:

  • Satin Nickel
  • Polished Brass
  • Oil Rubbed Bronze
Click here for Information & Pricing

Door Stops, Extra Tall

Door Stops, Extra Tall
  • This door stop is great for areas where you need an extra tall door stop (for example on out swinging doors)
  • Door stop measures about 6" from the floor to the top of the black rubber bumper
  • Base measures 3" in diameter, rubber bumper is about 1" in diameter
  • Made of solid brass base material
  • Includes all fasteners and masonary anchors needed for installation
  • Includes a hook plate to attach to your door to hold the door in the open position

Finishes:

  • Polished Brass
  • Oil Rubbed Bronze
  • Satin Nickel
Click here for Information & Pricing

Magnetic Door Holder, Flush Model

Magnetic Door Holder, Flush Model
  • Flush magnetic door holder is made up of two parts; a floor plate and a door plate. The door plate has a strong magnet installed on its underside. The Floor plate has a flat steel plate that is hinged on one side.
  • As the bottom of the door approaches the floor plate the magnet in the door plate pulls the steel lever up and grabs it to hold the door in place.
  • This magnetic door holder allows for a low profile less obtrusive magnetic door holder.
  • The floor plate is 2-7/16" in diameter and projects just 3/16".
  • The door plate measures 2-1/4' x 3/4" and projects 1".
  • For this device to work properly the bottom of your door must be no more than 7/8" from the surface of the floor below it.
  • Except for the steel lever plate and the magnet the entire device is made from solid brass.
  • Matching wood screws are included.

Finishes:

  • Satin Nickel
  • Oil Rubbed Bronze
  • Lifetime Polished Brass
Click here for Information & Pricing

Magnetic Door Holder

Magnetic Door Holder
  • These door holders are magnetic and will hold the door in the open position until it is pulled closed
  • The small 1-1/4" diameter button attaches to the back of the door with two wood screws (included)
  • The 3" tall magnetic holder attaches either to the floor in the vertical position or to the wall in the horizontal position.
  • The magnetic holder has a 1-3/4" diameter base
  • solid brass base material with some steel parts(necessary to make the magnet work) and internal steel attachment plates
  • Screws and plastic masonary anchors are included

Finishes:

  • Polished Brass
  • Oil Rubbed Bronze
  • Satin Nickel
  • Antique Brass
Click here for Information & Pricing

Magnetic Door Holder, Polycarbonate

Magnetic Door Holder, Polycarbonate
  • Magnetic door holder will hold the door in the open position until it is pulled closed.
  • Features a powerful magnet which has a 30lb pull.
  • Door holder is made up of two pieces; a door plate and a magnetic upright.
  • The door plate attaches to the back of the door. It is approximately 2" in diameter and projects 3/4".
  • The magnetic upright may be attached to either the floor in a vertical position or to the wall in a horizontal position. The magnetic upright measures 3" tall. Its baseplate is 2-1/8" in diameter.
  • This product is made from a very strong polycarbonate material. The magnet has a plated steel holder and receiver.
  • Mounting screws are included.

Finishes:

  • Brown
  • Ivory
Click here for Information & Pricing

Magnetic Door Holder, Small

Magnetic Door Holder, Small
  • Magnetic door holder will hold the door in the open position until it is pulled closed.
  • Features a magnet with an 18lb pull.
  • Door holder is made of two pieces; a door plate and a magnetic upright.
  • The door plate attaches to the back of the door. It measures 1-7/8" by 1-5/8" and projects 7/16".
  • The magnetic upright may be attached to either the floor in a vertical position or to the wall in a horizontal position. It measures 2-5/8" tall. Its base plate is approximately 1-3/4" by 2".
  • Product is made from plastic. The magnet is held in place by a steel holder and the wall plate has a steel plate to attract the magnet.
  • Mounting screws are included.

Finishes:

  • Brown
  • Ivory
Click here for Information & Pricing

Foot Bolt, Large

Foot Bolt, Large
  • Large Foot Bolt holds gates and doors in the open position.
  • Foot bolt easily engages and retracts by pressing your foot on one of two foot pads.
  • Made from steel, housing is blackcoated, bolt and foot pads are galvanized.
  • Includes 2" by 2" strike plate and black coated fasteners.
  • Housing measures 2" by 7-3/8". Projection is 3-1/4".
  • Bolt measures 5/8" by 5/8". Throw of bolt is 1".
Click here for Information & Pricing

5/8 Inch Chain Bolt

5/8 Inch Chain Bolt
  • Chain bolt for gates, doors, etc.
  • The chain bolt may be used on the top or bottom of the gate or door, or on both the top and bottom (if two are purchased).
  • Chain bolt provides a method of securing a gate or door in the open (or closed) position.
  • The bolt is made of 5/8" square steel. It is spring loaded and it is beveled on the latching end. The bevel allows the bolt to automatically retract and then lock when the bolt hits the strike.
  • The strike is also beveled to help the bolt retract.
  • An 18" chain is attached. The chain is used to release the bolt from the strike, thereby freeing the gate or door.
  • Dimensions of chain bolt:
    • Throw of bolt is 7/8".
    • Mounting plate measures 2" x 7-3/8".
    • Projection is 3/4"
  • Included are mounting screws, strike and chain bolt.
  • Mounting plate and its screws are black. Bolt, strike, chain and strike screws are zinc plated.
Click here for Information & Pricing

Spring Door Holder

Spring Door Holder
  • Spring door holder keeps door in the open position
  • Made up of two parts: the spring keeper and the post.
  • The post is solid brass. The spring keeper is plated spring steel.
  • After installation the door holder allows 2-5/8" clearance between surface of the door and the wall.
  • The spring keeper measures about 2" tall by 2-1/8" wide (base) by 3/4" thick.
  • The post measures 2" tall.
  • Wood screws are included.

Finishes:

  • Brass
  • Oil Rubbed Bronze
  • Satin Nickel
Click here for Information & Pricing
accredited business BBB
see what customers are saying

Over 10,000 Reviews
5 Star Average

Thank you for helping us find the hinges no store had! We are were very happy to find the hinges we were looking for - they look great ...
Very reliable vendor - would do business with again. Very prompt shipping and the order was processed flawlessly! ...
Guaranteed: All Valid Reviews Posted
StatisticsReview of HardwareSource.com

Related Products