Pivot Hinges for Cabinets

Pivot Hinges for Cabinets

  • Pivot hinges differ from other hinges in that they pivot around a point rather than along a longer hinge pin.
  • Pivot hinges can be made for inset doors, overlay doors and even partial inset doors.
  • Some pivot hinges can be installed as concealed hinges.
  • We have 56 different pivot hinges in this section.

Heavy Duty Reversible Pivot Hinge

Heavy Duty Reversible Pivot Hinge
  • For 1-1/8" to 1-3/8" thick doors
  • Reversible (non-handed) for Right Hand or Left Hand installations
  • For doors up to 60" high (75lb maximum weight)
  • For overlay type installations
  • Made from 0.125" steel
  • Wood screws are included
  • Horizontal piece (as shown in photo) measures 2-1/2" x 1"
  • Vertical flat piece (which mounts to wall) measures 3" x 7/8"
  • Rounded piece projects from wall 2-1/2"
  • Sold by the pair. A pair is what is required to install one door.

Finishes:

  • Satin Chrome
  • Polished Brass
Click here for Information & Pricing

Heavy Duty Pivot Hinge

Heavy Duty Pivot Hinge
  • For 1-1/8" to 1-3/8" thick door.
  • Heavy duty pivot hinge can be used for flush, recessed, or overlay type installations.
  • These pivot hinges are handed (Right Hand or Left Hand). Hinge in photo shows Left Hand set.
  • Made from 0.127" steel
  • Wood screws are included
  • Approximate measurements for top pivot: 2-1/2" long, 2-3/8" wide and 1" tall.
  • Approximate measurements for bottom pivot; 2-1/2" long, 2-5/16" wide and 1-1/2" tall.
  • Complete instructions are included.
  • Sold by the pair. A pair is what is needed to install one door.

Finishes:

  • Satin Chrome
  • Polished Brass
Click here for Information & Pricing

Heavy Duty Pivot Hinge w/Legs

Heavy Duty Pivot  Hinge w/Legs
  • For 1-1/8" to 1-3/8" thick door.
  • Heavy duty pivot hinge can be used for flush or recessed type installations.
  • These pivot hinges are handed (Right Hand or Left Hand). The hinge in the photo shows a Left Hand hinge.
  • Made from 0.125" steel.
  • Wood screws are included.
  • Approximate measurements for top pivot; 2-1/2" long by 2-1/8" wide.
  • Approximate measurements for bottom pivot; 2-1/2" long by 3" tall by 2-1/8" wide.
  • Complete instructions are included.
  • Sold by the pair. A pair is what is needed to install one door.

Finishes:

  • Satin Chrome
  • Polished Brass
Click here for Information & Pricing

Extra Heavy Duty Reversible Pivot Hinge

Extra Heavy Duty Reversible Pivot Hinge
  • For doors up to 159 lbs
  • For overlay doors 1-3/8" to 1-3/4" thick
  • Doors can be installed floor to ceiling
  • Full 180 degree opening
  • Made from 0.182" steel
  • Extra long screws are included
  • Horizontal piece (as shown in photo)measures 3" by 1-1/2"
  • Vertical flat piece (which mounts to wall) measures 3" x 1-1/8"
  • Rounded piece projects from wall 3"
  • Sold by the pair. A pair is what is needed to install one door.

Finishes:

  • Satin Chrome Plated (US26D)
Click here for Information & Pricing

Knife Type Pivot Hinge

Knife Type Pivot Hinge
  • Steel base material.
  • Size of each hinge is 1/8" thick, 3/8" wide, 2-1/4" long.
  • Each hinge uses 6 each #4 flat head screws (not included but offered for purchase during checkout). Order our SKU #286253.

Finishes:

  • Bronze plated
Click here for Information & Pricing

Right Angle Pivot Hinge

Right Angle Pivot Hinge
  • Right angle or "L" type pivot hinge.
  • Allows doors to be set back and swing clear of corner posts.
  • Hinge is handed and sold by the pair. You will receive one "left hand" and one "right hand" hinge for each pair ordered.
  • Steel base material.
  • Uses #4 flat head wood screws (not included but offered for purchase during checkout). Order our SKU 286253 for #4 x 5/8 bronze flat head wood screws. Order 8 screws for each pair of hinges ordered.
  • For dimensions click on link below

Finishes:

  • Bronze
Click here for Information & Pricing

Center Pivot Hinge

Center Pivot Hinge
  • Pivot hinge has two parts a leaf and pivot pin and a metal cup which holds the pivot pin.
  • The leaf measures 2" by 3/8" by 1/8" thick.
  • The cup is 3/8" tall by 3/8" in diameter.
  • Steel base material.
  • Uses a #5 flat head wood screw (not included but offered for purchase during checkout)
  • Order our SKU #286254 #5 x 5/8" bronze wood screw for this hinge. Each hinge takes 2 wood screws.

Finishes:

  • Bronze
Click here for Information & Pricing

Rear Pivot Hinge

Rear Pivot Hinge
  • Rear pivot hinge is made up of a wrap around leaf with a pivot pin and a knurled metal cup that holds the pivot pin.
  • The wrap around leaf measures 2" by 7/16" with a about a 1/2" distance to the wrap around.
  • The knurled metal cup is about 3/8" in diameter and fits in a 1/4" deep drilled hole.
  • The wrap around leaf mounts to the back of the door.
  • This hinge uses 2 each #6 x 5/8" Round Head Bronze plated screws per hinge (not included but offered for purchase during checkout). Order our SKU 286252 if you need screws.
  • Steel base material.

Finishes:

  • Bronze
Click here for Information & Pricing

Pivot Hinge 270 Degree

Pivot Hinge 270 Degree
  • Made for overlay cabinet doors up to 1" thick
  • Hinge pivots 270 degrees
  • The plate that attaches to the cabinet measures 1-1/4" x 1". The plate that attaches to the door measures 1-3/8" x 7/8". The pivot point projects out 1-7/16" from the cabinet surface
  • Steel base material
  • Screws not included
  • Uses 12 each #6 screws per pair of hinges(not included). We have not been able to find an exact finish match for the screws. We offer solid brass screws upon checkout which is fairly good match for the finish but not an exact match.

Finishes:

  • Antique Brass
Click here for Information & Pricing

Pivot Hinges, Corner Type, Stainless Steel

Pivot Hinges, Corner Type, Stainless Steel
  • Pivot hinge is made for use with 3/4" or 7/8" material.
  • Made from Type 430 stainless steel.
  • Natural finish.
  • Uses #5 flat head wood screws (not included)
  • Picture shown is right hand model.
  • These hinges will support a maximum door weight of 5.7lbs per two hinges.
  • When ordering hinges for your door order either 2 left hand hinges for the same door or two right hand hinges for the same door.
Click here for Information & Pricing

Wood Door Pivot Hinge

Wood Door Pivot Hinge
  • Pivot hinges for inset doors.
  • Can be used on trash receptacle doors, pet doors or any small pivot door.
  • Steel base metal, black finish.
  • 2 Sizes available.
Click here for Information & Pricing

Large Pivot Hinges

Large Pivot Hinges
  • For large cabinet doors and full size doors
  • Made of solid brass with steel pins
  • Flat head wood screws are included
  • For SKU numbers 838198 to 838242 the pivot screw is flush with the hinge (as shown in photo to left).
  • For SKU numbers 838250 to 838252, the pivot screw has a raised slotted head which measures about 3/4" in diameter and is 3/16" above the hinge surface. This large pivot hinge pivots on roller bearings. A pivot base is available for these 3 SKU numbers only. It is offered for purchase during checkout.
  • For tall doors an intermediate pivot hinge is recommended to keep the middle part of the door in alignment. Our SKU's 838204 through 838206 will work with any of the pivot hinges in this section. Intermediate pivots are offered for purchase during checkout.
  • The listed weight ratings are for a pair of hinges.

Finishes:

  • Polished Brass
  • Satin Nickel
  • Oil Rubbed Bronze
Click here for Information & Pricing

Variable Overlay Pivot Hinge

Variable Overlay Pivot Hinge
  • Variable overlay hinge for cabinet doors.
  • Made for 3/4" thick doors.
  • Hinge may be surface mounted or may be mortised into the surface (see install info link below).
  • This hinge is an exact duplicate of BP1242-2G Amerock hinge that was recently discontinued by Amerock.
  • The Amerock BP1242-2G was made in a zinc finish. Our hinge is a satin nickel finish.
  • The hinge is sold by the set. A set includes a top hinge and a bottom hinge as shown in the photo.
  • The horizontal leaf of this hinge attaches to the back of the door. The vertical leaf attaches to the front or face of the cabinet.
  • Wood screws are included.

PLEASE NOTE: this hinge is currently in limited supply. We reserve the right to limit purchase quantities.

.
Click here for Information & Pricing

Fast Food Hinge for Trash Receptacles

Fast Food Hinge for Trash Receptacles
  • Pivot hinge is used for fast food trash receptacles.
  • Hinges attach to the top of the pivoting trash receptacle door. Gravity returns the door to the closed position.
  • Hinge may also be used for pet doors or other cabinet doors.
  • If both leaves of the hinge are installed in a mortise (cutout) the hinge will be virtually invisible.
  • This hinge is also known as a Burger King hinge or a Mc Donald's hinge.
  • Hinge features a nylon bearing which produces a smooth closing action.
  • Normally used on 1" thick panels.
  • Click on link below for detailed hinge dimensions.
  • Hinge is made from steel, zinc chromate plated with nylon bearings.
  • Each hinge uses 4 each #10 flat head screws. Screws are not included but are offerered for purchase during checkout.
  • PLEASE NOTE: This hinge is sold by the each. Order two hinges per door.
Click here for Information & Pricing

Overlay Pivot Hinge

Overlay Pivot Hinge
  • Overlay pivot hinge
  • Made for frameless cabinets with 3/4" side panel thickness.
  • This hinge is a duplicate of Amerock's discontinued 1238 (BP1238) pivot hinge.
  • This hinge has a tab that fixes the overlay at 3/4". This is a full overlay for a 3/4" thick side panel.
  • Image shows one hinge leaf attached to a 3/4" side panel. The other hinge leaf would attach to the back of the door.
  • Installed as a full overlay hinge on a 3/4" side panel with a 3/4" thick door, the door would open 270 degrees.
  • The hinge can be used on face frame cabinets, but the overlay is fixed at 3/4".
  • Made from steel base material with a nickelor bronzefinish.
  • Hinge is sold by the pair, a pair is a Left hand and a Right hand (can also be considered a top and bottom) hinge.
  • Fasteners are not included but are offered for purchase during checkout. Each pair of hinges uses 12 each #6 flat head wood screws;
    • For hinge (nickel plated)SKU 286432 use screw SKU 652360
    • For hinge (bronze plated) SKU 286430 use screw SKU 286255

Finishes

  • Nickel
  • Bronze
Click here for Information & Pricing

Amerock Marathon Face Frame Pivot Hinge

Amerock Marathon Face Frame Pivot Hinge
  • For cabinets with a face frame
  • Steel base material with plastic spring mechanism
  • Matching wood screws are included
  • SKU numbers 399969, 399907 are for 1/4" overlay doors
  • SKU number 399961 is for a 3/8" partial inset door
  • These hinges are not handed
  • If you are trying to match an existing hinge look for the style number stamped on your hinge.
    • Style #4 (our SKU 399961)is for a 3/8" partial inset door (3/4" door thickness).
    • Style #5 (our SKU 399969)is for a 5/8" to 3/4" thick door with a 1/4" overlay.
    • Style #3 (our SKU 399907) is for a 1/2" thick door with a 1/4" overlay.

Please note: The #4 Marathon hinge has been discontinued by the manufacture and is no longer available.

    Finishes:

  • White
Click here for Information & Pricing

Amerock 1242 Pivot Hinge

Amerock 1242 Pivot Hinge
  • Pivot hinge for overlay doors.
  • Overlay is variable, no maximum overlay, minimum overlay is 1".
  • Hinge needs a minimum of 1" of width on the cabinet frame to install.
  • Made for 3/4" thick doors.
  • Made from steel base material andzinc chromateplated.
  • Each hinge uses up to 6 each #6 flat head wood screws (each pair of hinges uses up to 12 screws).
  • Screws are not included but are offered for purchase. Order our SKU 652360.
  • Elongated screw holes offer ease of adjustment during installation.
  • This hinge is sold by the pair. A pair is two hinges which means a top hinge and a bottom hinge.

Please note: this hinge has been discontinued by Amerock. Our SKU 732022 is a substitute for this hinge. You can click on the link below to go right to this hinge.

Click here for Information & Pricing

Pivot Base for Large Pivot Hinges

Pivot Base for Large Pivot Hinges
  • This pivot base is used with our Large Pivot Hinges (SKU numbers 838250, 838251 and 838252 only).
  • The pivot base replaces one leg of the pivot hinge (the non-door leg) to allow an easier installation if installing in concrete, marble, stone or any other material where a smaller cutout is desired.
  • Pivot base measures approximately 1.25" in height by 1" in diameter at the top and 3/4" in diameter at the bottom.
  • Made from solid brass.

Finishes:

  • Polished Brass
  • Oil Rubbed Bronze
  • Satin Nickel
Click here for Information & Pricing

Intermediate Pivot Hinge

Intermediate Pivot Hinge
  • These intermediate pivots work only with our pivot hinges in the SKU range from 838198 to 838252.
  • An intermediate pivot hinge is used for taller doors to keep the middle part of the door in alignment with the pivot hinges at the top and bottom of the door.
  • Made from solid brass material.
  • Includes matching wood screws.
  • Each hinge leaf measures 2-1/2" tall by 1-1/4" wide by 5/16" thick. Total width of hinge including hinge barrel is 2-1/2".

Finishes:

  • Satin Nickel
  • Polished Brass
  • Oil Rubbed Bronze
Click here for Information & Pricing

Small Spring Loaded Pivot Hinge

Small Spring Loaded Pivot Hinge
  • Small spring loaded pivot hinge for inset doors
  • The hinge is made of two parts; a spring loaded pin housing and a plastic bushing (pin receiver)
  • Both hinge parts install by drilling a hole and press fitting them in place
  • The spring loaded pin housing measures 1-3/8" long by 1/4" diameter. The pin diameter is 5/32" and projects 1/4"
  • The plastic bushing is 7/16" in outside diameter
  • Maximum door opening is approximately 140 degrees
  • This hinge will work on door thicknesses ranging from 1/2" to 13/16"
  • This hinge is made of plastic with a steel pin and spring.
  • Hinge is sold by the pair. Order 1 pair per door.
  • Tab adjustment screw is not included.
  • PLEASE NOTE: This hinge is not a "self-closing" hinge. The spring is in the pin receiver and is meant only to keep the pin in place after installation.

Finishes:

  • Black Plastic
Click here for Information & Pricing

Semi-Concealed Pivot Hinge

Semi-Concealed Pivot Hinge
  • Semi-concealed pivot hinge, only the tip shows through from the cabinet front.
  • To install cut an angled 7/32" slot through the edge of the door.
  • For door thickness of 5/8" to 3/4"
  • Door opens 270 degrees when installed on a 5/8" door.
  • Door opens 255 degrees when installed on a 3/4" door.
  • Hinges measures approximately 1-3/4" tall and 2" wide as shown in photo.
  • This hinge is sold by the pair. A pair includes a top hinge (as shown in photo) and a bottom hinge. The hinges are not handed, they will work on both a left hand and right hand door.
  • Steel base material.
  • Uses #6 Oval Head wood screws (not included). Order our SKU #400993 for a screw in an oil rubbed bronze finish that is a good match. Order 12 screws per pair of hinges. Screws are offered for purchase during checkout.

Finishes:

  • Dark Bronze Plated
Click here for Information & Pricing

Pivot Hinge, Wrap Around

Pivot Hinge, Wrap Around
  • This hinge is for a full overlay door with no cabinet face frame.
  • Works on door thicknesses up to 3/4"
  • Wrap around feature assures that all screws go into solid wood rather than end grain
  • Small leaf measures 2" by 3/8"
  • Large leaf measures approximately 1-7/8" by 1-1/8".
  • Hinge is sold by the pair. A pair includes a top pivot and a bottom pivot.
  • Photo shows the top pivot
  • Product uses 12 each #5 Flat Head wood screws per pair of hinges(not included but offered for purchase during checkout). Order our #5 x 5/8" Bronze plated flat head wood screw SKU # 286254.
  • Steel base material.
  • PLEASE NOTE: THIS HINGE IS NO LONGER AVAILABLE. IT IS NOT DISPLAYED. IT REMAINS ON THE WEBSITE AS REFERENCE. SKU NUMBER WAS 286406.

Finishes:

  • Bronze
Click here for Information & Pricing

Face Frame Pivot Hinge

Face Frame Pivot Hinge
  • For cabinets with a face frame
  • Steel base material with plastic spring mechanism
  • Matching wood screws are included
  • These hinges are not handed
  • If you are trying to match an existing hinge look for the style number stamped on your hinge.

PLEASE NOTE: The following versions of this hinge have been discontinued by the manufacture and are no longer available:

  • Style #4 (our SKU 399955) was for a 3/8" partial inset door (3/4" door thickness).
  • Style #5 (our SKU 399960) was made for a 5/8" to 3/4" thick door with a 1/4" overlay.
  • Style #3 (our SKU 399950)was for a 1/2" thick door with a 1/4" overlay.

Style #3 and Style #5 are still available in White, click HERE view these hinges.

Finishes:

  • Burnished Brass
Click here for Information & Pricing

Overlay Pivot Hinge, Stainless Steel

Overlay Pivot Hinge, Stainless Steel
  • Overlay door pivot hinge, made from Type 430 stainless steel.
  • IMPORTANT, PLEASE NOTE; These hinges are "handed". Order one left hand (SKU 658003)and one right hand hinge (SKU 658017) for each door you are installing.
  • PLEASE NOTE; the handing refers to where the hinge is located not whether the door is a left hand or right hand door. If you order a left hand hinge and a right hand hinge you can hinge either a right hand door or a left hand door.
  • Made for 3/4" thick doors.
  • Maximum door size: 17-23/32" wide 27-9/16" height.
  • These pivots are rated to hold 5.7 lbs per pair.
  • May be used as a 270 degree hinge if the pivot point is located just outside of the cabinet corner.
  • Each hinge uses 6 each #8 flat head screws. Not included but offered for purchase during checkout.

Finishes:

  • Stainless Steel, Natural
Click here for Information & Pricing

Amerock 1247 Pivot Hinge

Amerock 1247 Pivot Hinge
  • PLEASE NOTE:
  • Pivot hinge is made for 3/8" partial inset doors (also known as 3/8" inset doors with a 3/8" lip)
  • Fits doors that are 3/4" thick.
  • Sold as a pair which includes a left hand hinge right hand hinge.
    • The obsolete Amerock hinges were marked to show which hand the hinge was
    • The right hand hinge was marked "R", the left hand hinge was marked "L"..
    • If the hinges are used on horizontally swinging doors the left hand hinge is used as the top pivot and the right hand hinge is used as the bottom pivot..
    • The photo to the left shows the "Left Hand" hinge. The bottom leaf attaches to the edge of the face frame. The top leaf attaches to the back of the door.
  • The pivot point of the hinge installs in a 1/4" slot cut in the lip of the door from the backside of the door.
  • If you are replacing old hinges your hinge should have the number "1247" stamped on it (usually not visible when the hinge is installed).
  • Matching wood screws are included (8 screws per pair). Made from steel base material.

Finishes:

  • Burnished Brass
  • Zinc Chromate
  • Click here for Information & Pricing

    1247 Pivot Hinge for 3/8" Partial Inset Doors

    1247 Pivot Hinge for 3/8
    • Pivot hinge is made for face frame cabinets with a 3/8" partial inset door.
    • A 3/8" partial inset door is a door which partially insets into the cabinet opening and partially overlays the cabinet opening.
    • The door has a "rabbetted edge". The inset dimension measures 3/8" and the lip dimension measures 3/8".
    • This hinge is made for doors that are 3/4" thick.
    • The pivot point installs in a slot (approximately 1/4") cut into the door lip. When the door is closed, this slot is only visible from the side, and not from the front of the cabinet.
    • This hinge is a replica of a hinge that was once made by Amerock. It was Amerock's 1247 hinge and was available in two finishes: Burnished Brass and Zinc Chromate.
    • The hinge is sold by the pair. A pair includes a "Left Hand" hinge and a "Right Hand" hinge.
    • Can be used on doors that swing horizontally or doors that swing vertically.
    • Matching wood screws are included.
    • Installation:
      • The photo shows a Right hand and a Left hand hinge (one pair of hinges)
      • The bottom hinge leaf normally attaches to the edge of the face frame.
      • The top leaf normally attaches to the back of the door.

    Finishes:

    • Satin Nickel
    • Antique Brass
    Click here for Information & Pricing

    Large Center Pivot Hinge

    Large Center Pivot Hinge
    • Pivot hinge for windows and cabinet doors allows door to pivot up to 360 degrees depending on installation of door in frame.
    • Hinge is 4-5/8" long by 7/8" wide.
    • Hinge is 9/16" thick at thickest point.
    • The gap between the two leaves is 1/16". Hinge may be mortised into the bottom of the door and the frame for a minimum gap.
    • Made from 1/8" thick material.
    • Hinge pivots on an oilite, self-lubricating bearing.
    • Flat head wood screws are included.
    • Available in two models; solid brass or steel.
    • These hinges are sold by the pair (2 hinges) which is normally what you need to hinge one door.

    Finishes:

    • Steel, yellow zinc chromate plated
    • Solid Brass, natural, unfinished.
    Click here for Information & Pricing

    Pivot Hinges, Stainless Steel

    Pivot Hinges, Stainless Steel
    • Pivot hinges made from Type 430 stainless steel.
    • These pivot hinges are available in both Left Hand and Right Hand models and are available in two sizes.
    • May be used as 270 degree hinges if the pivot point is located just outside of the cabinet corner.
    • Available in two sizes; the small size fits up to a 11/16" thick door, the large size fits up to a 7/8" thick door.
    • For each door you are hinging order one left hand hinge and one right hand hinge.
    • Each hinge uses 4 to 6 each #4 flat head screws, not included but offered for purchase during checkout.

    Finishes:

    • Natural Stainless Steel
    Click here for Information & Pricing
    accredited business BBB
    Sign up for email updates from HardwareSource and get 5% OFF your next order!
    Email:

    see what customers are saying

    Over 10,000 Reviews
    5 Star Average

    Very reliable vendor - would do business with again. Very prompt shipping and the order was processed flawlessly! ...
    High quality, received them promptly without special shipping. Great quality, saved over 100.00 over Home Depot. ... (Read review)
    Guaranteed: All Valid Reviews Posted
    StatisticsReview of HardwareSource.com

    Related Products