• This hinged shelf support "locks in place" when in the horizontal position. Product allows shelf to fold down against wall when not in use.
 
• Horizontal piece measures 11" and vertical piece measures 5"
 
• Steel base material
 
• Bracket spacing should not exceed 32"
 
• When the shelf is in the fold-down position the gap between the wall and the bottom of the shelf is 2-1/2"
 
• Screws are included
 
• Weight rating is for a pair of supports when spacing does not exceed 32"
 
• Product is sold by the pair. A pair is two shelf supports

 
• White Powder Coat

 
• This product fastens a shelf to a wall and allows the shelf to hinge down flat against the wall.
 
• Extra heavy duty construction
 
• Size of each bracket is 23-3/4" by 21"
 
• Maximum load is 200lbs per pair of brackets
 
• Bracket spacing should not exceed 32"
• When the shelf is in the down position there will be a gap of 1" between the underside of the shelf and the surface of the wall.
• This piece of hardware has a very easy-to-use release mechanism. To fold the shelf or table back down against the wall, lift the front edge of the shelf about 1" and push in on the diagonal supports slightly. The table will then fold down to its vertical position.
• Screws are included
• These brackets are sold by the pair. One pair is needed per shelf.

 
• Zinc Chromate Plated

 
• Product fastens a shelf to a wall and allows the shelf to hinge down flat against the wall.
 
• Product is sold by the pair, a pair is two shelf supports.
 
• Bracket spacing should not exceed 32".
 
• Made from steel base material.
 
• Weight rating is for a pair of supports when spacing does not exceed 32".
 
• The maximum shelf width for each size support is listed below.
 
• The "Hinge Gap" dimension listed below is the distance from the wall to the underside of the shelf after installation.
 
• Screws are not included.

 
• White enameled

 
• Hinged shelf support allows shelf to fold down when not in use.
 
• Shelf will lock in place when in the horizontal position. Shelf releases by pressing a lever on the horizontal piece.
 
• Made from type 304 stainless steel.
 
• Vertical arm measures 6.5". Horizontal arm measures 12". Width of both arms is 7/8".
 
• After installation and when the shelf is in the folded down position, the gap between the bottom of the shelf and the wall it is attached to will be approximately 1-1/8".
 
• The manufacturer of this item does not provide any weight ratings for this product but it should be comparable to other similiar products that we stock.
 
• Uses 12 each #10 pan head screws, not included but offered for purchase during checkout.
 
• This product is sold by the pair. A pair is two shelf supports.

 
• Polished Stainless Steel

 
• Table leaf hinge allows table leaf to fold down into vertical position or to lock into horizontal position.
 
• Table leaf hinge is approximately 16" in length when in the "up" position. Click on link below for more specific dimensions.
 
• Features a release button which is located near the end of the table leaf. Release button releases the lock on the hinge and allows table leaf to be lowered into vertical position.
 
• For table leaves up to approximately 14" in front to back depth.
 
• Manufacturer recommends a maximum load capacity of 66lbs per pair.
 
• Photo shows table leaf hinge in the "down" or vertical position.
 
• Made from steel base material.
 
• Uses 7 each #8 pan head screws per hinge, not included but offered for purchase during checkout.
 
• These hinges are sold by the each. You would normally order 2 each hinges per table leaf.

 
• Yellow zinc plated

 
• Folding bench seat hinge is extra heavy duty.
 
• A pair of these bench seat hinges will hold up to 1100 lbs.
 
• May also be used as a folding shelf support.
 
• When not in use the seat or shelf folds up against the wall. In the up position the seat or shelf is held in place by gravity. If a more secure hold fast is needed, it will be necessary to add something such as a chain or other more positive holding device.
 
• Wall mounting plate measures 8" tall by approximately 3.5". Plate is slightly over 1/4" thick.
 
• Fold down arm projects out from wall 15".
• Fold down arm is made from U-shaped steel and measures 1.5" x 1.5"
• Wall mount uses 4 each 3/8" diameter fasteners (not included). Arm uses 4 each 1/4" diameter fasteners (not included).
 
• Because of the large load capacity of this device, it is important to use a proper method of attachment to your wall. Different wall types will use different attachment methods. Be sure to seek advice from a professional if you are not knowledgable in this area.
 
• This product is sold by the "EACH". You will normally need to order 2 each for each bench seat or shelf you are hanging.

 
• Heavy Zinc Chromate Plating

 
• This hinge is for use as with a drop panel on a wall unit. Two legs will support the drop panel for use as a table or work surface.
 
• The hinge allows a 1" x 2-1/2" leg to swing 270 degrees from vertical so that it can be folded into the wall with the drop panel. Legs are concealed when drop panel is raised.
 
• Works only with a 3/4" thick table top
 
• Hinge shown in photo is in the "folded up" position.
 
• Steel base material, uses 6 each #6 flat head screws per hinge (not included but offered for purchase during checkout)

 
• Zinc Chromate

 
• Allows table leg to fold up under table when not in use
 
• Spring activated trigger release provides positive locking in both open and closed position
 
• Accomodates 1-1/2" square leg without cutting or shaping
 
• Steel base material
 
• Each hinge uses 6 each #6 round head screws (not included but offered for purchase during checkout). Order our SKU 286252 for a matching finish.

 
• Bronze plated

 
• Allows table leg to fold up under table when not in use
 
• This table leg hinge works with any size table leg
 
• Spring activated trigger release provides positive locking in both open and closed position
 
• Steel base material
 
• Screws are not included. For matching screws order our SKU 286252 (order 11 per hinge). Screws are offered for purchase during checkout.
 
• Size is approximately 2-1/8" tall by 2-1/4" wide by 3" thick
 

 
• Bronze plated

 
• Hinged brace for folding table legs
 
• One end attaches to underside of table and the other end attaches to table leg
 
• Positive locking feature
 
• Steel construction
 
• Sold by the pair, a pair includes two braces (one right hand, one left hand)
 
• For a table with 4 legs order 2 pairs
 
• Screws are included
 
• Size is 13-1/2" by 5/8"

 
• Zinc Chromate Plated

 
• This hinge works well for hinging a bench seat
 
• It is available with springs (as shown in photo) or without springs
 
• SKU 796030 (with springs) will counter balance a seat or lid weighing between 17 and 26lbs (keeps the seat from slamming shut and makes it easier to open)
 
• SKU 796033 (without springs) works as a hinge without the counter balancing feature for lighter seats. Keep in mind that this model will not keep the seat from slamming shut
 
• Both models allow the seat to open to 95 degrees
 
• With both models the seat will move forward about 4" as it opens the full 95 degrees
 
• Both models are sold by the pair. A pair includes a left hand hinge and a right hand hinge
 
• Requires 8 each #12 Pan Head wood screws per pair (not included but offered for purchase during checkout)
 
• This hinge is not recommended for toy boxes as it could be a danger to small fingers

 
• Yellow chromated

 
• Length is 9-1/2" in the fully open position
 
• For supporting box lids or table legs
 
• Steel base material
 
• Wood screws are included
 
• They are sold by the pair which is two supports
 
• Non-handed

 
• Brass plated

 
• Extra heavy brace is ideal for use on tables with folding legs
 
• Designed with a positive, easily operated locking feature
 
• Legs lie flat against table when legs are folded
 
• Steel construction
 
• Sold by the pair, a pair includes two braces (one right hand, one left hand)
 
• Screws are included
 
• Size is 16-5/8" by 1-1/4"

 
• Zinc Chromate Plated

 
• For drop leaf tables and folding shelves
 
• This product works in conjunction with a hinge (purchased separately) to hold the table leaf in a horizontal position.
 
• Chart above shows mounting dimensions
 
• Spring tension holds brace open
 
• Made from steel base material
 
• Overall length is 10-1/2"
 
• Two supports are needed per drop leaf (unless the drop leaf is very short)
 
• Screws are included.

 
• Black

 
• Hinge measures 2-3/4” in the open position.
 
• Hinge measures 1-1/2” along the knuckle.
 
• Made from Type 304 stainless steel.
 
• Uses #8 flat head screws (not included). Stainless steel screws are offered for purchase during checkout.

 
• Polished

 
• for heavy cabinet work, folding shelves and table drop leaves
 
• hinge is a surface mounted hinge (may be partially mortised into the surface)
 
• fast spun pins
 
• hole patterns and number may vary from picture depending on size of hinge
 
• steel base material
 
• wood screws are included

 
• Zinc Plated

 
• This hinge is used to raise and support a table leaf in the horizontal position without any other hardware except the hinge itself.
 
• This hinge is in use in many restaurants, by flipping up a rounded table leaf, a square or rectangular table can be turned into a round table. Hinge can also be used on square or other shaped leaves.
• The leaf will fold back 180 degrees under the table.
 
• Heavy duty built-in springs hold up the table leaf
 
• Strong heavy gauge steel
 
• Approximately 8” long by 5”
 
• We recommend using 10 each #8 flat head screws per hinge (not included). Flat head steel screws are offered for purchase during checkout.
• Order 2 hinges per table leaf
• Click on link below to see install instructions.
• Use caution when handling this hinge as the spring is very strong and can injure fingers.

 
• Zinc Plated

 
• Mounts on the edge of the table and leaf
 
• Mortises into the edge of the table with a 3/8 straight router bit
 
• Allows table leaf to flip over and support itself
 
• Solid brass with steel pins
• Overall width is 1-1/4"
 
• #6 x 5/8” flat head screws included
 
• Order 1 pair of hinges per table leaf

 
• Polished Brass

 
• made in England
 
• 1/2” length of joint
 
• 3” width open
 
• solid brass base material
 
• #6 x 3/4” flat head screws included

 
• Sanded Brass

 
• Hinge is used in RV's, Mobile Homes, etc. to extend the surface of a table
 
• Hinge mounts on bottom surface of table and leaf and allows the leaf to fold back on top of the table
 
• Hinge is self-supporting, no other hardware is required
 
• Hinge is surface mounted but a mortise cut is required for hinging mechanism
 
• Steel base material
 
• Hinge is not handed
 
• Uses #4 flat head screws (not included but offered for purchase during checkout)
 
• Each leaf measures approximately 1-5/8" by 3/4"
 
• The gap between the top and bottom plate when the table is in the closed position (as shown in the photo) is 1-5/8".
 

 
• Brass plated

 
• Pantograph type mechanism which lifts a shelf holding an item such as a blender, slicer, mixer or other appliance from inside a desk or cabinet. Places item at working height.
 
• Two powerful springs aid the shelf as it is raised or lowered
 
• Automatically locks in the raised position
 
• Release the locks to lower the shelf
 
• Made from .125" steel
 
• Measures 28" in the fully extended raised position (as shown in the photo)
 
• Maximum recommended load is 44lbs
 
• Maximum usable height inside the cabinet (lowered position) is 16-1/2"
 
• Minimum front to back cabinet depth is 19"
 
• Maximum shelf depth is 16"
 
• There is no maximum on the shelf width
 
• This item is sold by the pair which it what is needed to hang one shelf.
 
• Uses 28 each #6 Pan head screws for installation (not included but offered for purchase during checkout)

 
• This hinged tilt-lift table support is used wherever you need to lift a horizontal surface to a certain angle and hold it in place
 
• It is used on beds, sofas and drafting tables
 
• Lift to the desired angle and it locks in place. Lift again to release and it folds back down
 
• It features 10 positive locking positions
 
• Maximum operating arc is 112 degrees
 
• It is sold in pairs (a pair is two devices)
 
• Approximate length is 8.5"
 
• A hinge must be used at the pivot point (not included). We recommend two butt hinges or a piano hinge.
 
• Steel base material
 
• Screws are not included but are offered for purchase during checkout. A pair of supports uses 4 each #8 pan heads screws and 4 each #10 pan head screws.

 
• Zinc Chromate

 
• Stop holds hinge flat in horizontal position.
 
• Hinge mortises flush into surface of table.
 
• Hinge folds up 90 degrees and stops.
 
• Hinge measures 2-29/32” long x 1-1/2” wide.
 
• Hinge is 5/64" thick (11/32" at the thickest point). Thickest point measurement is taken with the hinge in its flat position.
 
• Solid brass base material.
 
• Flat head wood screws are included.

 
• Polished Brass
 
• Antique Brass

 
• Hinge measures 2” in the open position.
 
• Hinge is 1-1/2” wide.
 
• Hinge is 3/64" thick (9/32" at the thickest point). Thickest point measurement is taken with the hinge in its flat position.
 
• Made from Type 304 stainless steel.
 
• The hinge incorporates a stop which holds the hinge flat in the horizontal position.
 
• Hinge mortises flush into surface of table.
 
• Hinge folds back a full 180 degrees onto the table.
 
• Uses #6 flat head screws (not included). Stainless steel screws are offered for purchase during checkout.

 
• Polished

 
• Hinge measures 3-1/4” in the open position.
 
• Hinge measures 1-3/16” wide.
 
• Hinge is 1/16" thick (11/32" at the thickest point). Thickest point measurement is taken with the hinge in its flat position.
 
• Made from Type 304 stainless steel.
 
• Hinge incorporates a stop which holds the hinge flat in the horizontal position.
 
• Hinge mortises flush into surface of table.
 
• Hinge folds back a full 180 degrees onto the table.
 
• Uses #6 flat head screws (not included). Stainless steel screws are offered for purchase during checkout.

 
• Polished

 
• Hinge measures 3” in the open position.
 
• Hinge measures 1-1/2” wide.
 
• Hinge is 1/16" thick (5/16" at the thickest point). Thickest point measurement is taken with the hinge in its flat position.
 
• Made from Type 304 stainless steel.
 
• Hinge has a stop which holds the hinge flat in the horizontal position.
 
• Hinge mortises flush into surface of table.
 
• Hinge folds back a full 180 degrees onto the table.
 
• Uses #6 flat head screws (not included). Stainless steel screws are offered for purchase during checkout.

 
• Polished

 
• Hinge measures 3” in the open position.
 
• Hinge measures 1-1/2” wide.
 
• Hinge is 1/16" thick (11/32" at the thickest point). Thickest point measurement is taken with the hinge in its flat position.
 
• Made from Type 304 stainless steel.
 
• Hinge has a stop which holds the hinge flat in the horizontal position.
 
• Hinge mortises flush into surface of table.
 
• Hinge folds back a full 180 degrees onto the table.
 
• Uses #8 flat head screws (not included). Stainless steel screws are offered for purchase during checkout.

 
• Polished

 
• Stop holds hinge flat in horizontal position.
 
• Hinge mortises flush into surface of table.
 
• Hinge folds back a full 180 degrees onto the table.
 
• Rounded corners.
 
• Hinge measures 2-3/4” long x 1-37/64” wide.
 
• Hinge is 5/64" thick (5/16" at the thickest point). Thickest point measurement is taken with the hinge in its flat position.
 
• Solid brass base material.
 
• Flat head screws (#6 x 5/8”) are included.

 
• Polished Brass

 
• Hinge is an English reproduction.
 
• Locks open in flat position.
 
• Holds vertical at 90 degrees.
 
• Square ends.
 
• Hinge measures 2-1/2” long x 1-1/2” wide.
 
• Hinge is 1/8" thick (3/8" at the thickest point). Thickest point measurement is taken with the hinge in its flat position.
 
• Solid brass base material.
 
• Uses #6 flat head screws (not included). Flat head brass screws are offered for purchase during checkout.

 
• Satin Brass

 
• Hinge is an English reproduction.
 
• Locks open in flat position.
 
• Holds vertically at 90 degrees.
 
• Round ends.
 
• Hinge measures 3” long x 1-1/2” wide.
 
• Hinge is 5/32" thick (11/32" at the thickest point). Thickest point measurement is taken with the hinge in its flat position.
 
• Solid brass base material.
 
• Uses #6 flat head screws (not included). Flat head brass wood screws are offered for purchase during checkout.

 
• Satin Brass

 
• Measures 2-1/2" by 1-1/2".
 
• Hinge is 1/8" thick (5/16" at the thickest point). Thickest point measurement is taken with the hinge in its flat position.
 
• Solid brass base material.
 
• Spring loaded stop at 90 degrees.
 
• Screws are included.

 
• Dark antique brass

 
• Stop holds hinge flat in horizontal position.
 
• Hinge mortises flush into surface of table.
 
• Hinge folds back a full 180 degrees onto the table.
 
• Round ends.
 
• Hinge measures 2-3/4” long x 1-3/16” wide.
 
• Hinge is 5/64" thick (5/16" at the thickest point). Thickest point measurement is taken with the hinge in its flat position.
 
• Solid brass base material.
 
• Flat head screws (#6 x 5/8”) are included

 
• Polished Brass

 
• Butler tray table hinge with narrow dimension.
 
• Hinge measures 2-1/2" by 1/2". The hinge is 11/32" thick at its thickest point. The hinge leafs are 3/32" thick.
 
• Made from solid brass.
 
• Uses #5 or #6 flat head screws. #5 is the best choice and #6 is acceptable if #5 is not available. Screws are not included but are offered for puchase during checkout.
 
• These hinges are sold by the pair. A pair of hinges is what is needed to hinge one table leaf.

 
• Polished Brass
 
• Polished Chrome

 
• Very high quality, solid brass hinge. Designed for full mortise installation.
• This hinge works well on doors that are from 3/4" to 1" thick.
• Overall size is 2-1/2" tall by 1-11/16" (open).
• Tip-to-tip measurement is 3-1/2"
• Matching wood screws are included.
• One leaf is swaged to allow a smaller mortise.
• Middle screwholes are elongated to allow for vertical and horizontal adjustment during installation.
• Each leaf measures 11/16" by 2-1/2"
• Click on link to view a chart of available finishes for this hinge.
 
• PLEASE NOTE: the manufacturer of the "Satin Nickel, Matt" hinge calls it "Silver Satin". We believe that the term "Satin Nickel, Matt" is more in line with industry wide descriptions. The finish is a Satin Nickel finish that is slightly duller than a typical Satin Nickel finish.

• Flat Black
• Gloss Oil Rubbed Bronze
• Oil Rubbed Bronze
• Antique Copper
• Polished Brass
• Polished Nickel
• Polished Chrome
• Satin Nickel, Matt
• Iron / Pewter
• Venetian Bronze

 
• Very high quality, solid brass hinge. Designed for full mortise installation but can be used as a surface mounted hinge.
• This hinge works well on doors that are from 3/4" to 1" thick.
• Nominal size is 2" tall by 1-5/8" (open). The actual measurements are 1-31/32" x 1-19/32" (open).
• Tip-to-tip measurement is 2-3/4"
• Matching wood screws are included.
• Four screwholes are elongated to allow for vertical and horizontal adjustment during installation.
• Each leaf measures 1-31/32" by 11/16".
• Click on link to view a chart of available finishes for this hinge.
 
• PLEASE NOTE: the manufacturer of the "Satin Nickel, Matt" hinge calls it "Silver Satin". We believe that the term "Satin Nickel, Matt" is more in line with industry wide descriptions. The finish is a Satin Nickel finish that is slightly duller than a typical Satin Nickel finish.

• Flat Black
• Gloss Oil Rubbed Bronze
• Oil Rubbed Bronze
• Old Copper
• Polished Brass
• Polished Nickel
• Polished Chrome
• Satin Nickel, Matt
• Iron / Pewter
• Venetian Bronze

 
• Excellent quality solid brass full mortise hinge
 
• Measures 4-3/4" tip-to-tip
 
• Each leaf measures 3/4" wide by 2-1/4" tall (measurement does not include hinge barrel)
 
• Hinge barrel is approximately 7/16" in diameter
 
• One hinge leaf is offset to provide a minimum gap when the door is closed
 
• Matching wood screws are included

 
• Satin Nickel
 
• Polished Brass
 
• Oil Rubbed Bronze
 
• Antique Pewter
 
• Antique English
 
• Polished Nickel

 
• Excellent quality solid brass full mortise hinge made for doors that range from 3/4" to 1" thick.
 
• Measures 3-1/2" tip-to-tip.
 
• Each leaf measures 5/8" wide by 2-1/4" tall (measurement does not include hinge barrel).
 
• Hinge barrel is approximately 5/16" in diameter.
 
• One hinge leaf is offset to provide a minimum gap when the door is closed.
 
• Matching wood screws are included.

 
• Satin Nickel
 
• Polished Brass
 
• Oil Rubbed Bronze
 
• Antique Pewter
 
• Antique English
 
• Polished Nickel

 
• Beautifully finished solid brass hinge is made in Italy.
 
• Hinge is a lift-off hinge. Door can be removed without removing hinges.
 
• Each hinge plate measures approximately 2" by 11/16".
 
• Matching wood screws are included.
 
• Hinge measures 6" tip to tip.
 
• Hinge barrel is slightly offset and measures 1/2" in diameter.
 
• These hinges are handed. Order Left Hand hinges for left hand doors and Right Hand hinges for right hand doors.
 
• When viewing your cabinet from the front, your left hand doors are on the left side of the cabinet and your right hand doors are on the right side.
 
• Hinge shown in photo is a right hand hinge.
 
• PLEASE NOTE: the manufacturer of the "Satin Nickel, Matt" hinge calls it "Silver Satin". We believe that the term "Satin Nickel, Matt" is more in line with industry wide descriptions. The finish is a Satin Nickel finish that is slightly duller than a typical Satin Nickel finish.

 
• Satin Nickel, Matt
 
• Antique Brass
 
• Polished Brass
 
• Oil Rubbed Bronze

 
• Beautiful solid brass hinge, made in Italy.
 
• Measures 6-1/8" tip-to-tip, top hinge plate is 2-1/8" tall, bottom hinge plate is 2" tall.
 
• Fits cabinet doors with a 3/8" inset and a 3/8" lip.
 
• This hinge is a "lift off" hinge. After the hinges are installed the door may be lifted off the cabinet without uninstalling the hinges.
 
• These hinges are handed. Order Left Hand hinges for left hand doors and Right Hand hinges for right hand doors.
 
• When viewing your cabinet from the front, your left hand doors are on the left side of the cabinet and your right hand doors are on the right side.
 
• Hinge shown in photo is a left hand hinge.
 
• Free swinging hinge.
 
• Matching wood screws are included.
 
• PLEASE NOTE: the manufacturer of the "Satin Nickel, Matt" hinge calls it "Silver Satin". We believe that the term "Satin Nickel, Matt" is more in line with industry wide descriptions. The finish is a Satin Nickel finish that is slightly duller than a typical Satin Nickel finish.

 
• Oil Rubbed Bronze
 
• Satin Nickel, Matt
 
• Polished Brass
 
• Antique Brass

 
• Hinge is made of steel base material.
 
• Decorative finial tips.
 
• Size is 2" tall by 1-1/2 inch wide.
 
• Tip-to-tip measurement is 2-13/16".
 
• Flat head matching wood screws are included.
 
• Hinge is shown in polished brass finish. To view other finishes click on link below.

 
• Polished Brass
 
• Antique Copper
 
• Satin Nickel
 
• Polished Nickel
 
• Oil Rubbed Bronze

 
• Decorative finial tips on each pin end.
 
• Centered in-line wings require mortising only on the door.
 
• Steel base material.
 
• Each hinge uses 6 each #6 flat head screws (not included but offered for purchase during checkout). We are not able to obtain Antique English finished screws so we are offering brass screws as our best match for this finish.

 
• Antique English
 
• Polished Brass

 
• Very good quality solid brass full mortise hinge
 
• Made for door thicknesses of 3/4" to 1-1/8".
 
• Measures 4-3/4" tip-to-tip.
 
• Each leaf measures 13/16" wide by 2-1/4" tall (measurement does not include hinge barrel).
 
• Hinge barrel is approximately 7/16" in diameter.
 
• One hinge leaf is swagged to provide a minimum gap when the door is closed.
 
• Matching wood screws are included.
 
• Made from solid brass material.
 
• Hinge shown in photo is the Antique Brass finish.

 
• Polished Brass
 
• Antique Brass

 
• Very good quality solid brass hinge for armoires, cabinets, etc. Hinge is designed for full mortise installation on inset doors. Hinge is swagged to minimize gap between hinge leaves.
 
• Measures 12" tip-to-tip.
 
• Each leaf measures 13/16" wide by 2-1/4" tall (measurement does not include hinge barrel).
 
• Hinge barrel is approximately 7/16" in diameter.
 
• Length of hinge barrel between leaves is 3-7/8".
 
• Matching wood screws are included.

 
• Antique Brass
 
• Polished Brass

 
• Size is 2-1/2" tall by 1-5/8" wide
 
• Tip-to-tip measurement is 3-9/16"
 
• Decorative finial tips
 
• Steel base material
 
• Matching flat head screws are included
 
• Finish shown in photo is Satin Nickel

 
• Satin Nickel
 
• Statuary Bronze
 
• Antique Brass
 
• Polished Brass
 
• Oil Rubbed Bronze

 
• Excellent quality solid brass hinge
 
• Measures 8-3/8" tip to tip
 
• Each leaf measures 3/4" wide by 2-1/4" tall (measurement does not include hinge barrel)
 
• Hinge barrel is approximately 7/16" in diameter
 
• Matching wood screws are included.

 
• Oil Rubbed Bronze
 
• Antique Pewter
 
• Antique English
 
• Polished Nickel

 
• made in Italy
 
• beautifully polished finish
 
• solid brass
 
• upper half “lifts-off” of lower half
 
• hinges are handed left or right
 
• to determine which "hand" hinge you need, stand with your back to the side of the door which shows the hinge pins: the right hand hinge will be on your right hand side and the left hand hinge will be on your left hand side
 
• uses #7 flat head screws (not included)
 
• PLEASE NOTE; THESE HINGES HAVE BEEN DISCONTINUED BY THE MANUFACTURER. WE HAVE LIMITED STOCK ON HAND. DISCONTINUED HINGES ARE NOT RETURNABLE.

 
• Polished Brass

 
• made in Italy
 
• beautifully polished finish
 
• solid brass
 
• upper half “lifts-off” of lower half
 
• hinges are handed left or right
 
• to determine which "hand" hinge you need, stand with your back to the side of the door which shows the hinge pins: the right hand hinge will be on your right hand side and the left hand hinge will be on your left hand side
 
• uses #7 flat head screws (not included)
 
• PLEASE NOTE; THESE HINGES HAVE BEEN DISCONTINUED BY THE MANUFACTURER. WE HAVE LIMITED STOCK ON HAND. DISCONTINUED HINGES ARE NOT RETURNABLE.

 
• Polished Brass

 
• Very nice ball tip hinge made from steel.
 
• Available in five finishes.
 
• Hinge thickness is 0.040".
 
• Joint length means distance along hinge pin not including ball tips.
 
• Matching flat head screws are included.
 
• PLEASE NOTE: SKU 504525 is actually made from solid brass but since the screws that come with it are made from steel we must include this hinge in the steel hinge section.

 
• Polished Brass
 
• Oil Rubbed Bronze
 
• Satin Nickel
 
• Polished Nickel
 
• Antique Brass

 
• Drive in hinge is mounted by driving into pre-drilled holes.
 
• Doors can be lifted off with ease.
 
• Features a finial tipped barrel.
 
• SKU #286-262 is 2-3/4” long by 11/32” diameter barrel.
 
• SKU #286-263 is 4-3/8” long by 11/32” diameter barrel.
 
• Ribbed attachment pins are 7/32” diameter by 11/15” long.
 
• Made from steel base material.
 
• No screws are needed.

 
• Bronze Plated

• hinge is mounted by driving it into predrilled holes
 
• doors can be lifted off with ease
• features a finial tipped barrel
• ribbed pins are 7/32" diameter by 15/16"
• hinge is 2-5/8" long by 11/32" diameter
• steel base material
• no screws needed

• Brass plated

 
• steel base material
 
• decorative finial tip at each pin end
 
• 6 knuckle design
 
• flat head screws are included

 
• Antique English

 
• Available in two sizes; large (2-1/2" x 2-1/2") and small (2" x 2")
 
• Tip-to-tip measurements are 4-1/2" (large size) and 4" (small size)
 
• Hinge pin is loose and may be removed
 
• Photo to left shows the large size
 
• To see the small size click on the link below
 
• Screws (#6 flat head) are not included and are not available. We suggest using zinc plated screws. Sand the finish off the screw heads with very fine grain sandpaper and oxidize them with a mild acid so they match the natural look of these unique hinges.

 
• Natural Cast Iron, Unfinished

 
• Beautifully finished with ball tips on each end
 
• Made from Solid brass
 
• Number of screw holes varies with hinge size
 
• Matching flat head screws are included

 
• Polished Brass
 
• Antique Brass

 
• Best quality extruded hinges.
 
• Designed for installation on cabinets with a minimum 3/4” thickness.
 
• The tips on these hinges screw on and off and the hinge pins are removable.
 
• Hole patterns vary according to size of hinge.
 
• Solid brass.
 
• Flat head screws are included

The 3" x 2-1/2" hinges are thinner (0.093" rather than 0.125") than similiar sized hinges so they can be used as "screen door" hinges which tend to be installed as full surface hinges.

 
• Polished Brass
 
• Dark Bronze
 

 
• Very nice ball tipped hinge made from steel.
 
• Available in four finishes. The upper left hand hinge shown in the photo is the Oil Rubbed Bronze, (moving clockwise) Polished Brass, Polished Nickel, Satin Nickel.
 
• Hinge thickness is 0.059".
• Joint length means distance along hinge pin not including the ball tips.
• Photos to left show the 2-7/16" tall hinge with 6 screw holes per hinge. The 1-15/16" hinge has 4 screw holes per hinge.
 
• Matching flat head screws are included.
 
• PLEASE NOTE: These hinges have a loose pin. If the hinge is installed with the hinge pin in a vertical position, install the hinge so that the hinge pin can be pulled out from the top of the hinge rather than the bottom.

 
• Oil Rubbed Bronze
 
• Polished Brass
 
• Satin Nickel
 
• Polished Nickel

 
• Beautiful ball tipped cabinet hinge available in 10 different finishes.
 
• Made from solid brass.
 
• May be installed as a surface mounted hinge or as a full mortise hinge (3/4" to 1" door thickness).
 
• Hinge measures 1-15/16" tall by 1-9/16" wide.
 
• Features oblong holes which allow vertical and horizontal adjustment of hinge.
 
• Click on "Finish Chart" to view available finishes.
 
• Matching wood screws are included.

 
• Iron / Pewter
 
• Satin Nickel
 
• Oil Rubbed Bronze
 
• Polished Nickel
 
• Old Copper
 
• Flat Black
 
• Polished Brass
 
• Venetian Bronze
 
• Gloss Oil Rubbed Bronze
 
• Polished Chrome

 
• Click on the link below to go to our 'No-Mortise Hinge' section where you will find more Finial Tipped Hinges.

 
• High quality American made hinge
 
• Hinge measures 2" high (hinge pin length) by 3" wide by 1/8" thick
 
• Solid Brass base material
 
• Matching flat head wood screws are included
 

 
• Antique Brass

 
• High quality American made product
 
• Hinge measures 1-1/2" high (hinge pin length) by 2-3/8" wide by 3/32" thick
 
• Solid Brass base material
 
• Matching flat head wood screws are included
 

 
• Antique Brass

 
• for heavy cabinet work, folding shelves and table drop leaves
• hinge is a surface mounted hinge (may be partially mortised into the surface)
 
• fast spun pins
 
• hole patterns and number may vary from picture depending on size of hinge
 
• steel base material
 
• wood screws are included

 
• Zinc Plated

 
• hinge is used on the drop flap of a writing desk
 
• measures 3" long by 1/2" wide by 1/8" thick
 
• solid brass base material
 
• comes with matching flat head wood screws

 
• Antique Brass

 
• 3-1/8” open
 
• 1-3/16” wide
 
• 1/16” material thickness
 
• steel base material
 
• uses #8 flat head screws (not included but offered for sale during checkout).

 
• Brass plated

 
• 3-1/8" open
 
• 1-3/16" wide
 
• 1/16” material thickness
 
• Steel base material
 
• Uses #8 flat head screws (not included)
 

• Bronze plated
 

 
• Flap stays hold flap or desk top in horizontal position.
 
• They are meant to be used in conjunction with a hinge.
 
• By tightening the screws on the white plastic block, friction is increased to control how fast the flap drops.
 
• Available in 2 sizes.
 
• Screws are not included but are offered for purchase during checkout. Order 2 each #6 flat head screws for plastic blocks. Order 2 each #4 flat head screws for base attachment.

 
• Nickel plated steel, white plastic

 
• Flap stay supports fold down desk tops.
 
• Available in two sizes; 7-7/8" and 9-7/8". Choose the size that fits your "Inside Cabinet Height". See installation diagram below for more information on this.
• Features a brake adjustment screw to control braking action.
 
• Made from steel and die cast parts with nylon internal parts.
 
• Each flap stay uses 6 each #6 flat head screws (not included but offered for purchase during checkout).
 
• Non-handed; works in both right hand and left hand applications.

 
• Nickel Plated

 
• Drop stay gently lowers and holds drop down desk surfaces and flaps.
 
• Reversible, can be installed on left or right hand side.
 
• Length is approximately 9". For detailed dimensions, click on link below.
 
• This product is meant to be used with separate hinges.
 
• Click on the link below to see what flap sizes this product will support.
 
• Screws are included.

 
• Nickel plated steel, black plastic

 
• For secretary type desks.
 
• Hinge opens desk top to horizontal position.
 
• After installed, desk top will close to about 45 degrees (or 135 degrees from horizontal).
 
• Overall length of hinge is 7" in open position.
 
• Width of hinge is 3/4".
 
• Steel base material.
 
• Matching wood screws are included.

 
• Brass plated

 
• Lid support is convertible, reversible, adjustable and demountable.
• Can be used on a horizontal lid, a vertical lid or a drop down lid.
• The friction on the lid support is adjustable. It is active in one direction with no friction in the opposite direction.
 
• Both lid support attachments are demountable (they snap out) from from the lid support.
 
• The demountable feature allows you to reverse the direction that the friction is applied.
 
• The slide button near the hub of the lid support allows you to change the direction of the friction action from up-opening to down-opening.
 
• Overall length of lid support is approximately 8" not including attachment ends.
 
• Two lid supports can support a lid weighing up to 20 lbs.
 
• Made from die cast zamak
 
• Uses #6 flat head screws (not included but offered for purchase during checkout). Uses 4 screws per lid support.

 
• Nickel Plated

 
• This device may be used for limiting the swing of a cabinet door anywhere from 0 to slightly more than 90 degrees depending on how you elect to install the mounting plates.
 
• A typical installation would be to mount the right angle swivel plate on the inside surface of the door and to mount the second plate on the underside of a shelf or the underside of the top of the cabinet.
 
• Available in a "Left Hand" or "Right Hand" model.
 
• Use a "Right Hand" model if your door is hinged on the right hand side of the cabinet as you are facing the cabinet.
 
• This device may also be used to support drop down desk tops. If ordering for use as a drop down desk support, order one "Left Hand" and one "Right Hand" model.
 
• Uses 2 each #4 flat head screws (not included but offered for purchase during checkout).
 
• PLEASE NOTE: the photos to the left show the product in a vertical position. When used as a cabinet restraint they will be installed in a horizontal positon.

 
• Allows drop panel to fold down and hold at 90 degrees
 
• Fits a 35mm (1-3/8") hole
 
• Hinge is detachable and adjustable
 
• Zinc die cast material
 
• Hinge thickness is 1/2"
 
• Uses #5 Flat head screws (not included)

 
• Dark bronze
 
• Satin Brass
 
• Nickel

 
• Allows panel to fold down and hold at 90 degrees
 
• Fits a 35mm (1-3/8") hole
 
• Hinge is detachable and adjustable
 
• Zinc die cast material
 
• Hinge thickness is 15/32"
 
• Screws are not included

 
• Dark Bronze
 
• Nickel

 
• flap opens 90 degrees, flush with inside shelf
 
• fits flush in door & shelf surfaces, concealed from exterior
 
• 30mm Forstner or flat boring bit needed to install
 
• for 3/4” thick doors
 
• hinge thickness is 7/16"
 
• linkage is brass and steel
 
• hinge is made from nylon material
 
• Uses #4 x 5/8” oval head wood screws (Not included)

 
• White nylon

 
• Flap opens 90 degree flush with inside shelf
 
• Fits flush in door & shelf surfaces, concealed from exterior
 
• Click on link below for more install information
 
• Uses #3 Flat head screws (not included)
 
• Hinge is 3-way adjustable and detachable

 
• White plastic and Chrome plated

 
• Flap opens 90 degrees flush with inside shelf
 
• Fits flush in door & shelf surfaces, concealed from exterior
 
• Click on link below for more install information
 
• Uses #4 Flat Head screws (not included)
 
• Hinge is 3-way adjustable and detachable

 
• Dark Bronze plated
 
• Nickel plated

 
• Hinge is completely concealed when door is closed
 
• Maximum door opening is 180 degrees
 
• Click on specification link below for detailed dimensions
 
• Hinge is sold by the each. Usually two each are needed per door.
 
• Made entirely of type 304 stainless steel
 
• Flat head stainless wood screws are included
 
• Maximum door size is 17-23/32" wide by 27-9/16" tall with a 7/8" door thickness. Maximum door weight for a pair of hinges is 5.72 lbs.

 
• Satin stainless steel

 
• hinge is completely concealed when door is closed
 
• opens 180 degrees
 
• steel base material
 
• hinge shown in photo is SKU 900016
 
• screws included

 
• Satin Brass
 
• Satin Chrome
 
• Black Epoxy

 
• hinge is completely concealed when door is closed
 
• opens 180 degrees
 
• made from high strength plated steel and heavy duty zinc allow castings
 
• hinge shown in photo is SKU 900020
 
• matching screws are included

 
• Satin Brass
 
• Satin Chrome
 
• Black Epoxy

 
• Solid stainless steel hinges made by Soss. Suitable for marine environments, yachts, etc.
 
• For doors with a minimum door thickness of 1/2" or 3/4".
 
• Hinge is completely concealed when door is closed.
 
• Hinge opens a maximum of 180 degrees.
 
• Made from solid stainless steel.
 
• Matching stainless steel screws are included.
 
• Hinge shown in photo shows the polished stainless finish.
 
• PLEASE NOTE; Soss stainless steel hinges are sold by the each. You would normally need to order 2 or 3 hinges per door.

 
• Satin Stainless Steel
 
• Polished Stainless Steel

 
• Hinge is completely concealed when door is closed.
 
• Hinge opens a maximum of 180 degrees.
 
• Hinge shown in photo is SKU 900024.
 
• Hinges are made from high strength plated steel and heavy duty zinc alloy castings.
 
• Matching screws are included.
 
• PLEASE NOTE: THESE HINGES ARE NOW SOLD BY THE EACH (FORMERLY SOLD BY THE PAIR). FOR A TYPICAL DOOR YOU WOULD NORMALLY ORDER 2 OR 3 EACH.

 
• Satin Brass
 
• Satin Chrome
 
• Black Epoxy

 
• Light duty nylon hinge with steel linkages
 
• Affordable price
 
• Measures 1-1/4" by 1-1/4" by 15/32" thick (with hinge in closed position)
 
• Incorporated set screws expand wedge locks to secure in wood. No wood screws are necessary.
 
• For wood up to 13/16" thick
 
• Make mortise with a 12mm drill bit
 
• Sold by the each. Order 2 hinges per door.

 
• Black nylon

 
• Large (approx 3.25" tall) concealed hinge.
 
• Body is made of white polyamide, hinge face and linkage is made from Type 304 stainless steel.
 
• Excellent hinge for marine applications.
 
• Load capacity is 66lbs per pair of hinges and 110lbs for 3 hinges.
 
• Maximum door opening of 180 degrees.
 
• Uses 4 each #10 flat head screws per hinge (Not included but offered for purchase during checkout).

 
• White Polyamide with Stainless Face

 
• Large (approx 3.5" tall) concealed hinge.
 
• Body is made of brown polyamide, hinge face and linkage is made from Type 304 stainless steel.
 
• Excellent hinge for marine applications.
 
• Load capacity is 88lbs per pair of hinges and 132lbs for 3 hinges.
 
• Maximum door opening of 180 degrees.
 
• Uses 4 each #12 flat head screws per hinge (Not included but offered for purchase during checkout).

 
• Brown Polyamide with Stainless Face

 
• for right or left hand installations
 
• completely invisible from either side of the door when closed
 
• easy installation
 
• for light applications
 
• adjustable tensioning screw
 
• accurate drilling essential
 
• solid brass base material with brass links
 
• no screws needed
 
• PLEASE NOTE: these hinges are not recommended for vertical or load bearing applications. The manufacturer does not provide weight ratings on this product.

 
• Opens to 90 degrees.
 
• Made for use with frameless cabinets.
 
• Approximate size of hinge is 1-7/8" x 4-1/2".
 
• For full-overlay, half-overlay, or inset doors.
 
• When open, inside of door is flush cabinet style.
 
• No hole boring or mounting plates required.
 
• Maximum full overlay is 25/32”.
 
• For door thicknesses 5/8" to 3/4" and side panel thicknesses of 5/8" to 7/8"
 
• Available in free swinging or self closing models.
 
• Steel base material
 
• Uses 8 each #6 pan head screws (not included. Screws are offered for purchase during checkout)
 
• For hinges with bronze finish, order 8 each #286-252 per hinge (#6 x 5/8” pan head bronze screws).

 
• Bronze plated
 
• Nickel plated

 
• Self-closing, concealed hinge.
 
• Made for cabinets whose doors open back-to-back. Both doors will open without interfering with each other.
 
• Made for use on frameless cabinets
 
• Opening angle is 90 degrees.
 
• Approximate size of hinge is 1-3/4" x 4-1/8".
 
• No hole boring or mounting plates required.
 
• For full-overlay, half-overlay, or inset doors.
 
• When open, the door is offset 1/2".
 
• Maximum full overlay is 25/32".
 
• When used on inset doors the maximum door thickness is 3/4".
 
• Steel base material.
 
• Uses 6 each #6 pan head screws per hinge(not included but offered for purchase during checkout).

 
• Nickel plated

 
• Swing up hinge for overlay cabinet doors. Hinge allows door to swing up and hold in the open position.
 
• For overlay doors on frameless cabinets (cabinets without a face frame).
 
• Spring tension is adjustable to accomodate different size and weight doors.
 
• Final open position may be set at either 75 degrees or 90 degrees.
 
• Elongated screw slots allow door to be adjusted after installation.
 
• Please note; the manufacturer of this product does not provide any weight rating or door size information.
 
• Screws are included.
 
• These hinges are handed. Order one "Left Hand" model and one "Right Hand" model for each door. Hinge in photo is the "Right Hand" model.

 
• White epoxy coated

 
• For "up opening" lids
 
• Use on hampers, piano benches, chest lids, etc.
 
• Surface mounted
 
• In the fully open position the hinge measues 6" long by 13/16" wide.
 
• Hinge will hold lid open at 90 degrees
 
• Steel base material
 
• Uses #4 flat head screws (not included but offered for purchase during checkout). Uses 4 screws per hinge.
 
• Spring action holds lid in closed position
 
• When lid is closed hinge is completely concealed.

 
• Nickel plated

 
• Heavy duty Lift-up hinge for overhead compartments
 
• Used in RV's, Kitchens, Buses, Trains, Aircraft and Furniture Built-ins
 
• Click on link below to see usage illustration
 
• Use for either 5/8" or 3/4" door thicknesses
 
• Recommended door size per pair of hinges is 20" by 11"
 
• Suggested weight capacity per pair of hinges is from 1-1/2 lbs to 8-1/8 lbs
 
• Hinge features positive stops in both the open and closed positions
• Surface mounted and completely invisible when installed
• Hinge holds open at 75 degrees
• Screws are not included but are offered for purchase during checkout. Each hinge uses 8 each #6 pan head screws.

 
• Nickel finish

 
• This heavy duty hinge allows smooth, silent, sag-free opening to 175 degrees
 
• Hinge surface mounts to the inside of your frameless cabinet. Small screw holes are the only holes you need to drill.
 
• Hinge works on 5 different applications: full overlay doors, half-overlay doors, full inset doors, and mitered corner doors (click on link below for illustrations) It also works on 3/8" inset doors with a 3/8" lip (no illustration available)
 
• For normal use the hinge can be used on door thicknesses up to 1"
 
• If used on "back-to-back" cabinets a maximum of 13/16" is recommended
 
• Hardened steel construction (.082 gauge steel)
 
• Features spring closing mechanism so cabinet latches are not necessary
 
• Cabinet must have at least a 4-1/8" depth. Hinge measures approximately 4" long by 1-5/8" by 2".
• Screws are not included but are offered for purchase during checkout. Each hinge uses 10 each #6 pan head screws.

 
• Nickel Plated

 
• Allows drop panel to fold down and hold at 90 degrees
 
• Fits a 35mm (1-3/8") hole
 
• Hinge thickness is 1/2"
 
• Hinge is detachable and adjustable
 
• Zinc die cast material
 
• Uses #5 Flat head screws (not included)

 
• Dark bronze
 
• Satin Brass
 
• Nickel

 
• Allows panel to fold down and hold at 90 degrees
 
• Fits a 35mm (1-3/8") hole
 
• Hinge is detachable and adjustable
 
• Zinc die cast material
 
• Hinge thickness is 15/32"
 
• Screws are not included

 
• Dark Bronze
 
• Nickel

 
• flap opens 90 degrees, flush with inside shelf
 
• fits flush in door & shelf surfaces, concealed from exterior
 
• 30mm Forstner or flat boring bit needed to install
 
• for 3/4” thick doors
 
• linkage is brass and steel
 
• hinge is made from nylon material
 
• Uses #4 x 5/8” oval head wood screws (Not included)

 
• White nylon

 
• Flap opens 90 degree flush with inside shelf
 
• Fits flush in door & shelf surfaces, concealed from exterior
 
• Click on link below for more install information
 
• Uses #3 Flat head screws (not included)
 
• Hinge is 3-way adjustable and detachable

 
• White plastic and Chrome plated

 
• Flap opens 90 degrees flush with inside shelf
 
• Fits flush in door & shelf surfaces, concealed from exterior
 
• Click on link below for more install information
 
• Uses #4 Flat head screws (not included)
 
• Hinge is 3-way adjustable and detachable

 
• Dark Bronze plated
 
• Nickel plated

 
• Heavy duty Lift-up hinge for overhead compartments
 
• Used in RV's, Kitchens, Buses, Trains, Aircraft and Furniture Built-ins
 
• Click on link below to see usage illustration
 
• Use for either 5/8" or 3/4" door thicknesses
 
• Recommended door size per pair of hinges is 20" by 11"
 
• Suggested weight capacity per pair of hinges is from 1-1/2 lbs to 8-1/8 lbs
 
• Hinge features positive stops in both the open and closed positions
• Surface mounted and completely invisible when installed
• Hinge holds open at 75 degrees
• Screws are not included but are offered for purchase during checkout. Each hinge uses 8 each #6 pan head screws.

 
• Nickel finish

 
• Hinge is designed as a hinge for boat ladders.
 
• May be used anywhere a long hinge with a strong hinge knuckle is needed.
 
• Hinge is 6-3/4" long by 3/4" wide by 3/16" thick.
 
• Hinge knuckle is 1/2" diameter.
 
• Uses #10 flat head screws, not included but offered for purchase during checkout.

 
• Polished Stainless Steel

 
• double acting
 
• for folding screens that fold in and out
 
• hinges use flat head screws (not included)
 
• steel base material

 
• brass plated
 
• statuary bronze plated

 
• 2-7/8” open
 
• 1-1/2” wide
 
• 304 stainless steel
 
• uses #6 flat head screws (not included)

 
• Polished

 
• made in England.
 
• surface mounted
 
• 1-1/2” joint length
 
• 2-1/2” width open
 
• solid brass base material
 
• #6 x 3/4” flat head screws are included

 
• Polished Brass

 
• Narrow mounting leaves measure 1/2” wide x 1-1/4” long.
• Tight-lock friction discs enable firm adjustments.
 
• Solid brass base material.
 
• Uses #4 flat head screws (not included but offered for purchase during checkout). Uses 4 screws per hinge.
 

 
• Dull Brass

 
• Brake-action pivots.
 
• For vanity type mirrors.
 
• Wedge action permits tight secure fastening and easy removal.
 
• Hinge measures 1-11/16” long by 13/16” wide by 7/16” thick.
 
• Steel base material.
 
• Uses 4 each #4 flat head screws (not included but offered for purchase during checkout).

 
• Nickel plated
 
• Brass plated

 
• Mirror hinge screws hold an oval or round framed mirror on dresser uprights
 
• Also known as a "Toilet Screw"
 
• Sold by the pair which is enough hardware to install one mirror
 
• Includes 2 inserts which thread into the wooden mirror frame
 
• Includes a 1/4" spacer for each screw which goes between the mirror and the upright
 
• The screw will fit up to a 2-1/8" wide upright
 
• The threaded part can easily be cut with a hacksaw for narrower upright widths
 
• Made of brass, steel and die cast parts

 
• Polished Brass

 
• Mirror pivot hinges for attaching a mirror between posts.
 
• Each pivot unit measures 2" by 1-1/4".
 
• Made from steel base material.
 
• Matching round head wood screws are included.

 
• Brass plated

 
• For flush mounted, 180 degree opening doors.
 
• Overall length is 3-1/2”.
 
• Solid brass.
 
• #5 x 1/2” flat head screws are included.

 
• Polished Brass

 
• 3/8” offset for offset doors.
 
• Overall length is 4”.
 
• Solid brass.
 
• #6 x 3/4” flat head screws are included.

 
• Polished Brass

 
• steel base material
 
• concealed pivot hinge for inset doors
 
• drill 7mm hole for plastic bushing
 
• for wood doors up to 1" thick
 
• #6 x 1/2” pan head screws included

 
• Black

 
• stamped stainless steel
 
• grade 304
 
• light duty utility hinge
 
• small plate measures 3/4" x 1-1/2"
 
• large plate measures 1-1/2" x 1-1/2"
 
• uses #6 flat head screws (not included)

 
• Polished

 
• These hinges feature a loose joint which allows the door to be easily removed after the hinges are installed
 
• #5 x 3/4" flat head screws are included
 
• When ordering please note that these hinges come in Left Hand or Right Hand. (for example a pair of Left Hand hinges is 2 Left Hand hinges)
 
• Solid brass base material
 
• Click on the link below for more handing information
 

 
• Dark antique brass

 
• Hinge measures 4-1/2" high by 4" wide
 
• Loose joint hinge, opened door may be lifted off after installation
 
• Comes in either a right hand or left hand model
 
• Steel base material, comes complete with matching #12 wood screws
 
• Hinge thickness is .139". Hinge Pin diameter is .308".

 
• Satin Nickel
 
• Oil Rubbed Bronze
 
• Prime Coated

 
• Solid Brass "Lift-off" or "Loose Joint" hinges.
 
• Allows opened door to be lifted off without removing the hinges.
 
• Available in Left Hand or Right Hand models.
 
• All hinges are 1/16" in thickness.
 
• Screws are not included. All hinges use #6 flat head screws. Screws are offered for purchase during checkout.
 
• 1-1/2" hinge uses 8 screws per pair
 
• 2" hinge uses 12 screws per pair
 
• 2-3/4" hinge uses 16 screws per pair

 
• Polished Brass
 
• Polished Chrome

 
• No mortise style hinge. Hinge installs as a normal full mortise butt hinge but no mortising is required.
• Leaves only a 1/8" gap after installation.
 
• Top leaf rides on a ball bearing located on the top of the hinge pin.
 
• Hinge is not handed, may be used on left or right opening doors.
 
• Hinge shown in photo is shown in the "door open" position.
 
• Hinge is a lift off hinge, door may be lifted off after hinge is installed without removing any screws.
 
• Made from solid type 304 stainless steel.
 
• Available in two sizes, a 4" high hinge and a 5" high hinge.
 
• The 4" hinge leaf is 1-5/8" wide not including the hinge barrel. The hinge barrel diameter is 5/8".
 
• The 5" hinge leaf is 1-3/8" wide not including the hinge barrel. The hinge barrel diameter is 3/4".
• Weight ratings listed below are for a pair of hinges.
 
• Stainless steel flat head screws are included.

 
• Satin Stainless Steel

 
• "Quick Release" hinge features a hinge pin release mechanism that allows door or lid to be easily removed.
 
• Hinge pin is spring loaded to keep the door or lid safely locked on to the cabinet or box.
 
• To remove the door or lid, the hinge pin may be retracted by pushing the knurled knob down and pivoting it into the unlocked position.
 
• Hinge is designed to be surface mounted.
 
• Hinge measures approximately 1-3/4" tall and 2" wide in the open position.
 
• Made from solid stainless steel.
 
• Uses #6 pan head screws (4 screws per hinge), not included, but offered for purchase during checkout.
 
• PLEASE NOTE: These hinges are handed (Right Hand or Left Hand). Make sure to order one Right Hand AND one Left Hand hinge for each door or lid you are hanging. The image shown to the left is a "Right Hand" model.

 
• Satin Stainless Steel

 
• Hinges feature a loose joint so that door may be easily removed after installation
 
• Hinges are available in a "left hand" or a "right hand" model
 
• Hinge shown in photo is a "left hand" hinge
 
• Stainless steel base material (type 304 stainless)
 
• Hinges are metric so the inch dimensions listed below are approximate. Click on link below for exact metric dimensions.
 
• Uses #4 flat head screws (not included but offered for purchase during checkout). Each hinge uses 4 screws.
 
• Hinges are sold by "Each". Order 2 each per door.

 
• Stainless Steel

 
• Hinges feature a loose joint so that door may be easily removed after installation
 
• Hinges are available in a "left hand" or a "right hand" model
 
• Hinge shown in photo is a "left hand" hinge
 
• Stainless steel base material (type 304 stainless)
 
• Hinges are metric so the inch dimensions listed below are approximate. Click on link below for exact metric dimensions.
 
• Uses #4 flat head screws (not included but offered for purchase during checkout). Each hinge uses 6 screws.
 
• Hinges are sold by "Each". Order 2 each per door.

 
• Stainless Steel

 
• Hinge lifts apart so lid or door may be easily removed.
 
• Steel base material.
 
• Joint length is 1-5/16”.
 
• Open width is 1-5/16”.
 
• Uses #4 pan head screws (not included but offered for purchase during checkout). Uses 4 screws per hinge.

 
• Nickel Plated

• hinge is mounted by driving it into predrilled holes
 
• doors can be lifted off with ease
 
• features a finial tipped barrel
 
• ribbed pins are 7/32" diameter by 15/16"
 
• hinge is 2-5/8" long by 11/32" diameter
 
• steel base material
 
• no screws needed

 
• Brass plated

 
• Steel base material.
 
• Hinge lifts apart so lid or door may be easily removed.
 
• Joint length is 1-5/16”.
 
• Open width is 1-7/8”.
 
• Used on cabinet or case where a removable cover is desired uses
 
• Uses #6 pan head screws (not included included but offered for purchase during checkout).Uses 4 screws per hinge.

 
• Nickel Plated

 
• Drive in hinge is mounted by driving into pre-drilled holes.
 
• Doors can be lifted off with ease.
 
• Features a finial tipped barrel.
 
• SKU #286-262 is 2-3/4” long by 11/32” diameter barrel.
 
• SKU #286-263 is 4-3/8” long by 11/32” diameter barrel.
 
• Ribbed attachment pins are 7/32” diameter by 11/15” long.
 
• Made from steel base material.
 
• No screws are needed.

 
• Bronze Plated

 
• Hinge has 2 knuckle design.
 
• Hinge slips apart at knuckle so lid or door may be easily removed.
 
• Steel base material.
 
• Joint length is 1-1/4”.
 
• Open width is 1-1/2”.
 
• Uses #6 pan head screws (not included but offered for purchase during checkout). Uses 4 screws per hinge.

 
• Nickel Plated

 
• Hinge lifts apart so lid or door may be easily removed.
 
• Joint length is 2-1/4”.
 
• Open width is 1-7/8”.
 
• Steel base material.
 
• Uses #8 pan head screws (not included but offered for purchase during checkout). Uses 4 screws per hinge.

 
• Zinc Plated

 
• made in Italy
 
• beautifully polished finish
 
• solid brass
 
• upper half “lifts-off” of lower half
 
• hinges are handed left or right
 
• to determine which "hand" hinge you need, stand with your back to the side of the door which shows the hinge pins: the right hand hinge will be on your right hand side and the left hand hinge will be on your left hand side
 
• uses #7 flat head screws (not included)
 
• PLEASE NOTE; THESE HINGES HAVE BEEN DISCONTINUED BY THE MANUFACTURER. WE HAVE LIMITED STOCK ON HAND. DISCONTINUED HINGES ARE NOT RETURNABLE.

 
• Polished Brass

 
• made in Italy
 
• beautifully polished finish
 
• solid brass
 
• upper half “lifts-off” of lower half
 
• hinges are handed left or right
 
• to determine which "hand" hinge you need, stand with your back to the side of the door which shows the hinge pins: the right hand hinge will be on your right hand side and the left hand hinge will be on your left hand side
 
• uses #7 flat head screws (not included)
 
• PLEASE NOTE; THESE HINGES HAVE BEEN DISCONTINUED BY THE MANUFACTURER. WE HAVE LIMITED STOCK ON HAND. DISCONTINUED HINGES ARE NOT RETURNABLE.

 
• Polished Brass

 
• European style glass door hinges for inset, overlay and twin overlay glass doors.
 
• Hinges feature a 94 degree opening angle and 3 dimensional adjustment.
 
• This hinge system requires that the glass door have a 26mm hole bored for each hinge used.
 
• They work with glass thicknesses of 4.5mm to 7mm (slightly under 3/16 to slightly over 1/4 inch).
 
• The hinge system is made up of 4 items which are ordered separately; the hinge, the cover cap, the mounting plate and the wood screws for the mounting plate.
 
• The hinges come in 3 types; "Straight Arm" for overlay doors, "Half Cranked" for twin overlay doors (also known as "Back-to-Back" doors, and "Full Cranked" for inset doors.
 
• The "Cover Caps" (required to hold glass door to hinge system) are available in 3 finishes; flat black, chrome and gold. Screws to hold cover cap to hinge are included with hinge. The outside diameter of the cover cap is 1-1/4".
 
• All parts of the hinge and cover cap that touch the glass are plastic material.
 
• Order hinges and cover caps on this page. Mounting plates and wood screws are offered for purchase during checkout.
 
• Please check out information link to find SKU number for hinge mounting plates.

 
• Flat Black Cover Cap
 
• Chrome Cover Cap
 
• Gold Cover Cap

 
• Glass door hinge for inset applications
 
• Fits glass thickness of 4 to 8 mm (5/32" to 5/16").
 
• Hinge clamps to glass so no boring of glass is required. Clamp screws are included.
 
• Type 304 stainless steel.
 
• Maximum door size is 15-3/4" high by 23-5/8" wide.
• Hinge measures approximately 1" high by 1-1/4" wide by 3/4" thick. See dimensional diagram for actual measurements.
 
• Flat head wood screws are included.

 
• Polished Stainless Steel

 
• Glass door hinge for inset doors. No boring of glass is required.
 
• Made from Type 304 stainless steel.
 
• For glass doors 5/32" to 5/16" thick and up to 51" tall and 17-3/4" wide.
 
• Screws are included.
 
• Hinge measures approximately 2-3/8" tall and 1-1/4" wide and 3/4" thick.
 
• For exact dimension click on link below.

 
• Polished Stainless Steel

 
• Inset type glass door hinge.
 
• Requires two holes (approximately 3/8") bored in glass to install.
 
• Hinge measures approximately 1-7/8" tall.
 
• Leaf that attaches to glass is about 1-3/8" wide.
 
• Leaf that attaches to side panel is about 2" wide.
 
• Screws to attach hinge to side panel are not included (uses #6 Pan Head, stainless steel screws are offered for purchase during checkout). All other fasteners are included.
 
• The hinge body is polished stainless steel (type 304). The fixing plate (attaches to front of glass) is made from zinc allow and is polished chrome plated.
 
• For glass thicknesses from 3/16" to 5/16".
 
• For glass doors up to 26 lbs and 25.5" wide (per pair of hinges).

 
• installs easily without boring through glass doors
 
• positive self-locking feature eliminates the need for magnetic or touch    latches
 
• glass secured with large rubber tipped screw
 
• opening angle is 160 degrees
 
• hinge measures approximately 1-3/16" tall and each hinge wing is approximately 1-1/2" wide.
 
• for left or right hand installations
 
• glass thickness to 1/4”
 
• steel base material
 
• uses #6 round or pan head screws (not included). Uses 4 screws per pair of hinges.

 
• Chrome plated
 
• Brass plated

 
• Installs easily without boring through glass doors.
 
• Includes self adhesive pressure plates and screws.
 
• Screw-mounts to side of cabinet.
 
• Opening angle is 110 degrees.
 
• For left or right hand installations.
 
• For glass thicknesses of 3/16” to 1/4".
 
• Side mount plate measures 1-1/2" by 5/8" by 5/8". Glass bracket measures 1-5/8" x 3/4" tall by 1/2" thick.
 
• Made from steel base material.
 
• Uses #6 pan or round head screws (not included). Uses 4 screws per pair of hinges.

 
• Chrome plated
 
• Brass plated
 
• Black

 
• Installs easily without boring through glass doors.
 
• Opening angle is 110 degrees.
 
• For left or right hand installations.
 
• For glass thicknesses to 1/4” (6.5mm).
 
• Visible height is 20 mm (Approx. 25/32”).
 
• Outside diameter of pivot point bushing is 5/16".
 
• Made from steel base material.
 
• Includes self adhesive pressure plates, machine screws, press-fit black plastic bushings and set screws to hold glass.

 
• Chrome plated
 
• Brass plated
 
• Black finish

 
• installs easily without boring through glass doors
 
• includes self adhesive pressure plates, machine screws, press-fit black plastic bushings, and set screws to hold glass
 
• opening angle is 110 degrees
 
• for left or right hand installations
 
• to install the press-fit black plastic bushing drill a 3/8" diameter hole which is 1/4" deep
 
• Glass thickness to 3/16” (5 mm)
 
• Visible height is 13.5 mm (Approx. 17/32”)
 
• steel base material

 
• Chrome plated
 
• Brass plated
 
• Black finish

 
• Glass door hinge for overlay doors.
 
• Stainless steel base material with an aluminum cap screw.
 
• Free swinging.
 
• Uses #4 flat head wood screws (not included but offered for purchase during checkout.) Order 3 screws per hinge.
 
• Overlay dimension is 3/8".
 
• Requires a 7mm hole drilled in the glass.
 
• For glass thicknesses of 4mm (5/32"), 5mm (3/16") and 6mm (15/64")

 
• Stainless Steel

 
• Glass door hinge for inset doors
 
• Requires a 7mm hole drilled in the glass
 
• Free swinging
 
• For glass thicknesses of 4mm (5/32"), 5mm (3/16"), and 6mm (15/64")
 
• Maximum door weight for a pair of hinges is 8.8 lbs
 
• Maximum door size is 17-3/4" wide by 27-1/2" high per pair of hinges
 
• Uses #4 flat head wood screws (not included but offered for purchase during checkout) Order 3 each screws per hinge.
 
• Made from steel base material.

 
• Polished Chrome
 
• Polished Brass

 
• Glass door hinge for cabinets without a face frame.
 
• Hinge overlays side panel.
 
• Hinge requires small hole bored in glass to install
 
• Steel base material. Snap catch is made from nylon.
 
• Uses #4 flat head screws not included but offered for purchase during checkout. (for side panel attachment). Order 3 each screws per hinge.
 
• Fasteners to attach hinge to glass are included.
 
• Hinge features built in nylon snap catch to hold door in closed position.
 
• Hinge shown in photo is chrome hinge. Hinge is show in 1/2 open position.

 
• Chrome
 
• Polished Brass
 
• Flat Black

 
• Aximat hinge for glass door with wood side panel.
 
• Includes plastic spacer plates to protect glass.
• For glass thickness of 5 mm to 6 mm.
 
• Available in two sizes; SKU 796604 is for a door overlay of 12 mm and a side panel thickness of 16 mm. SKU 796606 is for a door overlay of 15 mm and a side panel thickness of 19 mm.
 
• Each hinge uses two types of screws. One #5 or #6 flat head screw to attach to the side panel and two "System screws" to attach the the side panel. The screw holes for the "System screws" are located under the black plastic cover shown in the photo.  Screws are not included but offered for purchase during checkout.
 
• Hinge will allow door to open 270 degrees.
 
• Made from steel base material.

 
• Nickel plated

 
• Magnetic touch latch and steel plate work together to provide a latch for glass doors.
 
• To operate the touch latch simply push it in, it will then pop the glass door out so it can be easily opened.
 
• Use the single touch latch where there is only one door.
 
• Use the double touch latch where two doors close together in the middle of the cabinet.
 
• Use the "Push-In" touch latch where you have a wooden horizontal shelf. The Push-In touch latch pushes into a hole drilled in the edge of the shelf.
 
• The wrap around plates are available in 3 finishes.
 
• The wrap around plate is made out of steel so as to work with the magnet in the touch latch.
 
• The wrap around plates will work for 3/16" thick glass and include self adhesive plastic cushioning material for the glass. They are held in by pressure.
 
• The wrap around plates will work for 1/4" glass if you shim the glass with a small piece of plastic tape. Discard the self adhesive plastic cushioning material.
 
• Touch latches use a #4 Round head screw (not included) Screws are offered for purchase during checkout.
 
• Be sure to order one wrap around plate for each glass door.

 
• Black Plastic (Single Touch Latch)
 
• Black Plastic (Double Touch Latch)
 
• Black Plastic (Push-In Touch Latch)
 
• Polished Brass (Plate)
 
• Polished Chrome (Plate)
 
• Black (Plate)

 
• Used for standard wall to glass installation.
 
• Solid brass drop forged construction.
 
• Stainless steel reversible hinge pin.
 
• Opens to 90 degrees
 
• Hinge pin is reversible which allows it to be set at 0 degrees or 5 degrees. The 5 degree setting holds the door against a stop.
 
• Springs are hardened stainless steel coil springs.
 
• Fits tempered glass sizes from 3/8" to 1/2"
 
• Wall plate measures 1-15/16" by 3-1/2" tall. Glass leaf measures 2-1/8" by 3-1/2" tall.
 
• Hinge is designed to fit industry standard templates.
 
• Comes complete with gaskets, screws, allen wrench.
 
• PLEASE NOTE; installation of this hinge requires a cutout in the glass where the hinge is installed.

Weight rating using 3/8" glass; using 2 hinges maximum weight is 80lbs and 28" maximum width. Using 3 hinges maximum weight is 120lbs and 32" maximum width.

Weight rating using 1/2" glass; using 2 hinges maximum weight is 80lbs and 26" maximum width. Using 3 hinges maximum weight is 120lbs and 30" maximum width.

 
• Bright Chrome
 
• Brushed Nickel

 
• Used for standard glass to glass installation.
 
• Solid brass drop forged construction.
 
• Stainless steel reversible hinge pin.
 
• Opens to 90 degrees
 
• Hinge pin is reversible which allows it to be set at 0 degrees or 5 degrees. The 5 degree setting holds the door against a stop.
 
• Springs are hardened stainless steel coil springs.
 
• Fits tempered glass sizes from 3/8" to 1/2"
 
• Each glass leaf measures 2-1/4" wide by 3-1/2" tall.
 
• Hinge is designed to fit industry standard templates.
 
• Comes complete with gaskets, screws, allen wrench.
 
• PLEASE NOTE; installation of this hinge requires a cutout in the glass where the hinge is installed.

Weight rating using 3/8" glass; using 2 hinges maximum weight is 80lbs and 28" maximum width. Using 3 hinges maximum weight is 120lbs and 32" maximum width.

Weight rating using 1/2" glass; using 2 hinges maximum weight is 80lbs and 26" maximum width. Using 3 hinges maximum weight is 120lbs and 30" maximum width.

 
• Brushed Nickel
 
• Oil Rubbed Bronze

 
• Used for standard glass to glass installation.
 
• Solid brass drop forged construction.
 
• Stainless steel reversible hinge pin.
 
• Used to mount a door to a fixed glass side panel that runs at a 135 degree angle to the door.
 
• Hinge pin is reversible which allows it to be set at 0 degrees or 5 degrees. The 5 degree setting holds the door against a stop.
 
• Springs are hardened stainless steel coil springs.
 
• Fits tempered glass sizes from 3/8" to 1/2"
 
• Each leaf measures 2/1/8" wide by 3-1/2" tall.
 
• Hinge is designed to fit industry standard templates.
 
• Comes complete with gaskets, screws, allen wrench.
 
• PLEASE NOTE; installation of this hinge requires a cutout in the glass where the hinge is installed.

Weight rating using 3/8" glass; using 2 hinges maximum weight is 80lbs and 28" maximum width. Using 3 hinges maximum weight is 120lbs and 32" maximum width.

Weight rating using 1/2" glass; using 2 hinges maximum weight is 80lbs and 26" maximum width. Using 3 hinges maximum weight is 120lbs and 30" maximum width.

 
• Bright Chrome
 
• Brushed Nickel
 
• Polished Brass
 
• Oil Rubbed Bronze

 
• Used for standard glass to glass installation.
 
• Solid brass drop forged construction.
 
• Stainless steel reversible hinge pin.
 
• Opens to 90 degrees
 
• Hinge pin is reversible which allows it to be set at 0 degrees or 5 degrees. The 5 degree setting holds the door against a stop.
 
• Springs are hardened stainless steel coil springs.
 
• Fits tempered glass sizes from 3/8" to 1/2"
 
• Each leaf measures 2-1/4" wide by 3-1/2" tall.
 
• Hinge is designed to fit industry standard templates.
 
• Comes complete with gaskets, screws, allen wrench.
 
• PLEASE NOTE; installation of this hinge requires a cutout in the glass where the hinge is installed.

Weight rating using 3/8" glass; using 2 hinges maximum weight is 80lbs and 28" maximum width. Using 3 hinges maximum weight is 120lbs and 32" maximum width.

Weight rating using 1/2" glass; using 2 hinges maximum weight is 80lbs and 26" maximum width. Using 3 hinges maximum weight is 120lbs and 30" maximum width.

 
• Bright Chrome
 
• Brushed Nickel
 
• Polished Brass